Effects of Geometrical Parameters on Performances of Wind Energy Harvester with a Chamber

2013 ◽  
Vol 562-565 ◽  
pp. 1075-1079
Author(s):  
Xue Feng He ◽  
Yi Fu Fang ◽  
Zhi Gang Du
Keyword(s):  
Wind Speed ◽  
Wind Energy ◽  
Output Power ◽  
Energy Harvester ◽  
Maximum Output Power ◽  
Geometrical Parameters ◽  
Flexible Beam ◽  
Front Wall ◽  
Maximum Output ◽  
Critical Wind Speed

To improve the performances under low speed wind, a wind energy harvester similar to harmonicas was proposed. The harvester mainly includes a cuboid chamber and a cantilevered beam. The front wall of the chamber is opened as the air entrance and a rectangular hole is opened on the sidewall as the exit. The cantilever composed of a piezoelectric sheet and a flexible beam was fixed onto the sidewall of the chamber near the exit. Experimental results show that the width and height of the chamber significantly affect critical wind speed and output power, respectively. The initial attack angle of the cantilever has important influence on the critical wind speed. Blunt body at the air entrance could remarkably decrease the critical wind speed. For a prototype with a 60 mm×20 mm×13 mm chamber, the length of the cantilever of 30 mm and the length of the piezoelectric sheet of 8 mm, the measured maximum output power is 1.1 mW under 17 m/s wind.

scholarly journals Bidirectional Piezoelectric Energy Harvester

Sensors ◽  
2019 ◽  
Vol 19 (18) ◽  
pp. 3845 ◽  
Author(s):  
Andrius Čeponis ◽  
Dalius Mažeika ◽  
Artūras Kilikevičius
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Maximum Output Power ◽  
Geometrical Parameters ◽  
Maximum Output ◽  
Electrical Characteristics ◽  
Harmonic Vibrations ◽  
Piezoelectric Energy ◽  
Out Of Plane ◽  
Bending Modes

This paper represents a numerical and experimental investigation of the bidirectional piezoelectric energy harvester. The harvester can harvest energy from the vibrating base in two perpendicular directions. The introduced harvester consists of two cantilevers that are connected by a particular angle and two seismic masses. The first mass is placed at a free end of the harvester while the second mass is fixed at the joining point of the cantilevers. The piezoelectric energy harvester employs the first and the second out of plane bending modes. The numerical investigation was carried out to obtain optimal geometrical parameters and to calculate the mechanical and electrical characteristics of the harvester. The energy harvester can provide stable output power during harmonic and impact-based excitation in two directions. The results of the investigations showed that energy harvester provides a maximum output power of 16.85 µW and 15.9 4 µW when the base has harmonic vibrations in y and z directions, respectively. Maximum output of 4.059 nW/N and 3.1 nW/N in y and z directions were obtained in case of impact based excitation

Effect of Wind Speed and Blade Deflection Angle on the Output Power of Horizontal-Axis Wind Turbines

2018 ◽  
Vol 6 (2) ◽  
pp. 75-81
Author(s):  
Muhammad Al Badri
Keyword(s):  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
Output Power ◽  
Deflection Angle ◽  
Maximum Output Power ◽  
Simulation Software ◽  
Horizontal Axis ◽  
Maximum Output ◽  
Horizontal Axis Wind Turbine

This study is aimed to optimize the conversion of kinetic wind energy into electrical energy. Wind energy is a sustainable energy that is preferred to generate electricity for its low generation cost and low CO2 emissions. The considerations of physical principles of a horizontal axis wind turbine were involved in the study. Controlling of the blade angle deviation and the turbine rotation direction was also considered. For this purpose, a complete wind turbine system was setup by using the computerized simulation software (PSCAD). The system was running at five different cases with different wind speeds and different angles of the blade. The system was successfully generating a maximum output power from the wind turbine based on the changing of the deflection angle of the blade. Also the system would shut down if there were no matching between the wind speed and its direction with the angle of the blade.

scholarly journals Study of the Properties of a Hybrid Piezoelectric and Electromagnetic Energy Harvester for a Civil Engineering Low-Frequency Sloshing Environment

Energies ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 391
Author(s):  
Nan Wu ◽  
Yuncheng He ◽  
Jiyang Fu ◽  
Peng Liao
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Civil Engineering ◽  
Maximum Output Power ◽  
Low Frequency ◽  
Electromagnetic Energy ◽  
Maximum Output ◽  
Piezoelectric Film ◽  
Hybrid Energy ◽  
Level Height

In this paper a novel hybrid piezoelectric and electromagnetic energy harvester for civil engineering low-frequency sloshing environment is reported. The architecture, fabrication and characterization of the harvester are discussed. The hybrid energy harvester is composed of a permanent magnet, copper coil, and PVDF(polyvinylidene difluoride) piezoelectric film, and the upper U-tube device containing a cylindrical fluid barrier is connected to the foundation support plate by a hinge and spring. The two primary means of energy collection were through the vortex street, which alternately impacted the PVDF piezoelectric film through fluid shedding, and the electromotive force (EMF) induced by changes in the magnetic field position in the conducting coil. Experimentally, the maximum output power of the piezoelectric transformer of the hybrid energy harvester was 2.47 μW (circuit load 270 kΩ; liquid level height 80 mm); and the maximum output power of the electromagnetic generator was 2.72 μW (circuit load 470 kΩ; liquid level height 60 mm). The low-frequency sloshing energy collected by this energy harvester can drive microsensors for civil engineering monitoring.

Modelling of Mechanical Nonlinearity in an Electromagnetic Vibration Energy Harvester Using a Forced Duffing Equation

2012 ◽  
Author(s):  
S. D. Moss ◽  
L. A. Vandewater ◽  
S. C. Galea
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Duffing Oscillator ◽  
Maximum Output Power ◽  
Vibration Energy ◽  
Maximum Output ◽  
Vibration Energy Harvesting ◽  
Vibration Energy Harvester ◽  
Homotopy Analysis ◽  
Wire Coil

This work reports on the modelling and experimental validation of a bi-axial vibration energy harvesting approach that uses a permanent-magnet/ball-bearing arrangement and a wire-coil transducer. The harvester’s behaviour is modelled using a forced Duffing oscillator, and the primary first order steady state resonant solutions are found using the homotopy analysis method (or HAM). Solutions found are shown to compare well with measured bearing displacements and harvested output power, and are used to predict the wideband frequency response of this type of vibration energy harvester. A prototype harvesting arrangement produced a maximum output power of 12.9 mW from a 12 Hz, 500 milli-g (or 4.9 m/s2) rms excitation.

scholarly journals Study on the Efficiency and Dynamic Characteristics of an Energy Harvester Based on Flexible Structure Galloping

Energies ◽  
2021 ◽  
Vol 14 (20) ◽  
pp. 6548
Author(s):  
Peng Liao ◽  
Jiyang Fu ◽  
Wenyong Ma ◽  
Yuan Cai ◽  
Yuncheng He
Keyword(s):  
Numerical Simulation ◽  
Wind Speed ◽  
Physical Model ◽  
Energy Harvester ◽  
High Efficiency ◽  
Lateral Displacement ◽  
Maximum Output Power ◽  
Flexible Structure ◽  
Maximum Output ◽  
Cfd Numerical Simulation

According to the engineering phenomenon of the galloping of ice-coated transmission lines at certain wind speeds, this paper proposes a novel type of energy harvester based on the galloping of a flexible structure. It uses the tension generated by the galloping structure to cause periodic strain on the piezoelectric cantilever beam, which is highly efficient for converting wind energy into electricity. On this basis, a physical model of fluid–structure interaction is established, and the Reynolds-averaged Navier–Stokes equation and SST K -ω turbulent model based on ANSYS Fluent are used to carry out a two-dimensional steady computational fluid dynamics (CFD) numerical simulation. First, the CFD technology under different grid densities and time steps is verified. CFD numerical simulation technology is used to simulate the physical model of the energy harvester, and the effect of wind speed on the lateral displacement and aerodynamic force of the flexible structure is analyzed. In addition, this paper also carries out a parameterized study on the influence of the harvester’s behavior, through the wind tunnel test, focusing on the voltage and electric power output efficiency. The harvester has a maximum output power of 119.7 μW/mm3 at the optimal resistance value of 200 KΩ at a wind speed of 10 m/s. The research results provide certain guidance for the design of a high-efficiency harvester with a square aerodynamic shape and a flexible bluff body.

Micro-power-generator for energy harvesting from vortex induced vibration

2020 ◽  
Vol 64 (1-4) ◽  
pp. 573-580 ◽  
Author(s):  
Yuansheng Chen ◽  
Cong Gu ◽  
Hao Wang ◽  
Jinhao Qiu ◽  
Sunchong Zhao
Keyword(s):  
Wind Speed ◽  
Output Power ◽  
Maximum Output Power ◽  
Sensor Nodes ◽  
Structural Vibration ◽  
Maximum Output ◽  
Power Generator ◽  
Piezoelectric Energy ◽  
Micro Power ◽  
Micro Power Generator

A micro-power-generator is developed with piezoelectric ceramics, which can convert the structural vibration energy generated by wind power into electricity to provide energy for micro-devices such as wireless sensor nodes. The vibration modes of the device are analyzed. The standard interface circuit for piezoelectric energy recovery and LTC3588-1 voltage stabilization circuit are selected, and the hardware circuit of the device is designed. The output voltage and power characteristics of micro-power-generator were analyzed under different loads, frequencies and amplitudes. The experimental results show that under the same wind speed, When the blunt body is a cuboid, the power generation effect of this device is the best under the optimal load, with the maximum output power of 350.7 μW. Under the same load with the same shape and structure, the load voltage and output power increase with the increase of wind speed.

scholarly journals Topology Selection and Parametric Design of Electromagnetic Vibration Energy Harvesters by Combining FEA-in-the-Loop and Analytical Approaches

Energies ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 627 ◽  
Author(s):  
Seong-yeol Yoo ◽  
Young-Woo Park ◽  
Myounggyu Noh
Keyword(s):  
Output Power ◽  
Permanent Magnets ◽  
Energy Harvester ◽  
Maximum Output Power ◽  
Electromagnetic Energy ◽  
Vibration Energy ◽  
Maximum Output ◽  
Primary Concern ◽  
Energy Harvesters ◽  
Analytical Approaches

Electromagnetic energy harvesters have been used to capture low-frequency vibration energy of large machines such as diesel generators. The structure of an electromagnetic energy harvester is either planar or tubular. Past research efforts focus on optimally designing each structure separately. An objective comparison between the two structures is necessary in order to decide which structure is advantageous. When comparing the structures, the design variations such as magnetization patterns and the use of yokes must also be considered. In this study, extensive comparisons are made covering all possible topologies of an electromagnetic energy harvester. A bench mark harvester is defined and the parameters that produce maximum output power are identified for each topology. It is found that the tubular harvesters generally produce larger output power than the planar counterparts. The largest output power is generated by the tubular harvester with a Halbach magnetization pattern (94.7 mW). The second best is the tubular harvester with axial magnetization pattern (79.1 mW) when moving yokes are inserted between permanent magnets for flux concentration. When cost is of primary concern, the tubular harvester with axial pattern may become a best option.

Complex Impedance Matching for Power Improvement of a Circular Piezoelectric Energy Harvester

2011 ◽  
Vol 148-149 ◽  
pp. 169-172 ◽  
Author(s):  
Hong Yan Wang ◽  
Xiao Biao Shan ◽  
Tao Xie
Keyword(s):  
Output Power ◽  
Power Output ◽  
Energy Harvester ◽  
Impedance Matching ◽  
Maximum Output Power ◽  
Complex Impedance ◽  
Complex Conjugate ◽  
Maximum Output ◽  
Piezoelectric Energy ◽  
Matching Load

The impedance matching and the optimization of power from a circular piezoelectric energy harvester with a central-attached mass are studied. A finite element model is constructed to analyze the electrical equivalent impedance of the circular piezoelectric energy harvester. Furthermore, the complex conjugate matching load is used to extract the maximum output power of the energy harvester. The power output from complex conjugate matching load is compared with the power output from the resistive matching load and a constant resistance, separately. The results suggest that the complex conjugate matching can result in a significant increase of the output power for all frequencies. The effective bandwidth of the piezoelectric energy harvester is extended significantly.

System Parameter Optimization for a Frequency-Up-Conversion Piezoelectric Energy Harvester With Backward Mechanical-Electric Coupling Effect

2020 ◽  
Vol 142 (4) ◽  
Author(s):  
Fengxia Wang
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Coupling Effect ◽  
Maximum Output Power ◽  
Harmonic Excitation ◽  
Maximum Output ◽  
Piezoelectric Energy ◽  
Dynamic Damping ◽  
The Galerkin Method ◽  
The Relationship

Abstract In this work, a parametric model for a frequency-up-conversion piezoelectric energy harvester (PEH) was developed based on the Galerkin method. The PEH is composed of a piezoelectric bimorph and a stopper, which was subjected to a harmonic excitation. Although backward coupling results in a structure dynamic damping, models with neglected backward coupling were often adopted to estimate the output power of a piezoelectric energy harvester. The purpose of this work is to examine the effect of backward coupling on the dynamic response and the output power generation for a frequency-up-conversion PEH. With the same base excitations, we compared the dynamics and output energies of two cases: (1) neglecting the backward coupling effect (BCE) in the model and (2) including the BCE in the model. To obtain the optimum gap with maximum output power, we studied the relationship between the output power and the gap of the steady-state solutions. From the analytical results, it was found that the BCE can be neglected as long as there is no impact or the output power is small. However, once impacts get involved, the piezoelectric backward effect dominates the total damping due to small mechanical damping which is true for most PEH. The backward coupling will significantly diminish both the vibration and output power. Therefore, if the BCE is neglected in an impact-driven frequency-up-conversion PEH, the simplified model will exaggerate the output power.

Sign in / Sign up

Export Citation Format

Share Document