Mechanical Properties of PM CNT-Dispersed Cu Composite

2017 ◽  
Vol 737 ◽  
pp. 320-325 ◽  
Author(s):  
Hisashi Imai ◽  
Katsuyoshi Kondoh ◽  
Junko Umeda

Microstructural and mechanical properties of powder metallurgy (PM) with carbon nanotube (CNTs) dispersed copper (Cu) composites were investigated in detail. Pure copper powder was coated with un-bundled CNTs by using the zwitterionic surfactant solution containing CNTs. The powder rolling process was applied to increase the powder surface area to be coated with CNTs. The total rolling reduction of Cu-CNT composite powder by 5 steps rolling was about 75%. With increasing the number of rolling steps, the content of CNTs coated on the Cu powder surface increased because of the increment of the flat surface area of flaky Cu rolled powder. As a result, the CNT content was 0.67mass% after 5 steps powder rolling. It was about twice as that of as-coated Cu-CNT composite powder without rolling. The grain size of PM extruded Cu-CNT composite was about one fifth of that of the extruded monolithic Cu material without CNT. Yield stress of the extruded Cu-CNT composite via the rolling process was 192 MPa, which is about twice that of the extruded monolithic Cu material (88 MPa). CNTs distributed at primary particle boundaries were effective to prevent the grain coarsening by their pinning effects, and this grain refinement was the main strengthening factor of the Cu-CNT composite via rolling process.

2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
Saeed Tamimi ◽  
Mostafa Ketabchi ◽  
Nader Parvin ◽  
Mehdi Sanjari ◽  
Augusto Lopes

Severe plastic deformation is a new method to produce ultrafine grain materials with enhanced mechanical properties. The main objective of this work is to investigate whether accumulative roll bonding (ARB) is an effective grain refinement technique for two engineering materials of pure copper and interstitial free (IF) steel strips. Additionally, the influence of severely plastic deformation imposed by ARB on the mechanical properties of these materials with different crystallographic structure is taken into account. For this purpose, a number of ARB processes were performed at elevated temperature on the materials with 50% of plastic deformation in each rolling pass. Hardness of the samples was measured using microhardness tests. It was found that both the ultimate grain size achieved, and the degree of bonding depend on the number of rolling passes and the total plastic deformation. The rolling process was stopped in the 4th cycle for copper and the 10th cycle for IF steel, until cracking of the edges became pronounced. The effects of process temperature and wire-brushing as significant parameters in ARB process on the mechanical behaviour of the samples were evaluated.


Alloy Digest ◽  
2008 ◽  
Vol 57 (3) ◽  

Abstract Ansonia alloy C14500 has unique fabrication properties while maintaining both physical and mechanical properties close to pure copper. The addition of Tellurium makes the alloy free machining. This datasheet provides information on composition, physical properties, hardness, tensile properties, and shear strength. It also includes information on forming, heat treating, machining, and joining. Filing Code: CU-752. Producer or source: Ansonia Copper & Brass Inc.


Metals ◽  
2019 ◽  
Vol 9 (3) ◽  
pp. 345 ◽  
Author(s):  
Lianzan Yang ◽  
Yongyan Li ◽  
Zhifeng Wang ◽  
Weimin Zhao ◽  
Chunling Qin

High-entropy alloys (HEAs) present excellent mechanical properties. However, the exploitation of chemical properties of HEAs is far less than that of mechanical properties, which is mainly limited by the low specific surface area of HEAs synthesized by traditional methods. Thus, it is vital to develop new routes to fabricate HEAs with novel three-dimensional structures and a high specific surface area. Herein, we develop a facile approach to fabricate nanoporous noble metal quasi-HEA microspheres by melt-spinning and dealloying. The as-obtained nanoporous Cu30Au23Pt22Pd25 quasi-HEA microspheres present a hierarchical porous structure with a high specific surface area of 69.5 m2/g and a multiphase approximatively componential solid solution characteristic with a broad single-group face-centered cubic XRD pattern, which is different from the traditional single-phase or two-phase solid solution HEAs. To differentiate, these are named quasi-HEAs. The synthetic strategy proposed in this paper opens the door for the synthesis of porous quasi-HEAs related materials, and is expected to promote further applications of quasi-HEAs in various chemical fields.


2010 ◽  
Vol 168-170 ◽  
pp. 969-972
Author(s):  
Jian Qing Qian ◽  
Ji Ping Chen ◽  
Bao Qiao Wu ◽  
Jie Ca Wu

The application of vanadium-nitrogen alloy to develop a certain low carbon high strength H-beam steel was determined through the combination of theoretical study, product requirements and existing practical conditions. The specific rolling process was further defined through laboratory experiments. The developed low carbon high strength H-beam steel was trial produced and its properties were also analyzed. The results showed that the newly developed low carbon high strength H-beam steel had excellent mechanical properties and good weldability.


2015 ◽  
Vol 60 (4) ◽  
pp. 2821-2826 ◽  
Author(s):  
A. Wierzba ◽  
S. Mróz ◽  
P. Szota ◽  
A. Stefanik ◽  
R. Mola

The paper presents the results of the experimental study of the three-layer Al-Mg-Al sheets rolling process by the ARB method. The tests carried out were limited to single-pass symmetric and asymmetric rolling processes. An Al-Mg-Al package with an initial thickness of 4 mm (1-2-1 mm) was subjected to the process of rolling with a relative reduction of 50%. To activate the shear band in the strip being deformed, an asymmetry factor of av=2 was applied. From the test results, an increase in the tensile strength of the multi-layer Al-Mg-Al sheets obtained from the asymmetric process was observed. Microhardness tests did not show any significant differences in aluminium layer between respective layers of sheets obtained from the symmetric and the asymmetric process. By contrast, for the magnesium layer, an increase in microhardness from 72 HV to 79 HV could be observed for the asymmetric rolling. The analysis of the produced Al-Mg-Al sheets shows that the good bond between individual layers and grain refinement in the magnesium layer contributed to the obtaining of higher mechanical properties in the multi-layer sheets produced in the asymmetric process compared to the sheets obtained from the symmetric process.


1994 ◽  
Vol 67 (2) ◽  
pp. 342-347
Author(s):  
Moira Marx Nir ◽  
Robert E. Cohen

Abstract Tensile failure properties of syndiotactic 1,2 polybutadiene/trans 1,4 polybutadiene crystalline blends are improved by addition of 5–10% amorphous 1,2 polybutadiene/1,4 polybutadiene diblock copolymer. The effect of block molecular weight and microphase behavior of the diblock copolymer was investigated. Heterogeneous diblocks enhance blend properties to a greater extent than homogeneous diblocks. In blends with enhanced properties, percent coverage of interfacial surface area by diblock is on the order of 10%.


Sign in / Sign up

Export Citation Format

Share Document