Effect of Hydroentanglement on Structures and Properties of Wet-Laid Paper Sheets

2019 ◽  
Vol 821 ◽  
pp. 201-205
Author(s):  
Chao Deng ◽  
Xian Gyu Jin
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Air Permeability ◽  
Water Absorbency ◽  
Structures And Properties ◽  
Before And After ◽  
Properties Of Materials ◽  
Scanning Electron

In this work, pulp/lyocell wet-laid paper sheets have been consolidated by hydroentanglement techniques. Scanning electron microscopy has been used to evaluate the structures of wet-laid paper sheets before and after hydroentanglement. Wet tensile strength along longitudinal (preferential) and transverse directions show the effect of hydroentanglement techniques on the mechanical properties of wet-laid paper sheets. In addition, the air permeability and water absorbency properties of materials have been evaluated. The results show that the structures of wet-laid paper sheets become fluffy and fiber entanglements increase after consolidation. The wet tensile strength values of wet-laid paper sheets at the longitudinal and transverse directions are increased by 109.0% and 78.7%, respectively after hydroentanglement. The air permeability and water absorbency of wet-laid paper sheets are increased by 957.6% and 137.0%.

scholarly journals STRUCTURES AND PROPERTIES OF NATURAL RUBBER/ORGANOCLAY NANOCOMPOSITES

2011 ◽  
Vol 14 (1) ◽  
pp. 30-38
Author(s):  
Hien Quang Pham ◽  
Son Thanh Thanh Do ◽  
Nieu Huu Nguyen
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Natural Rubber ◽  
Abrasion Resistance ◽  
X Ray Diffraction ◽  
X Ray ◽  
Structures And Properties ◽  
Scanning Electron

Natural rubber (NR), 30% epoxidized natural rubber (ENR30) and organoclays (Nanomer I28E and I30E) are blended in Brabender. Dispersions of the organoclay in NR are investigated by X – ray diffraction (XRD) and scanning electron microscopy (SEM). The results revealed the increase of dispersion efficiency by the addition of ENR30 as a compatibilizer. The existence of organoclay I28E reduces the vulcanization time, while torque value increases slightly and mechanical properties (abrasion resistance, modulus M100, modulus M300, tensile strength, tear strength) are improved considerably.

scholarly journals Analysis of PLA Composite Filaments Reinforced with Lignin and Polymerised-Lignin-Treated NFC

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2174
Author(s):  
Diana Gregor-Svetec ◽  
Mirjam Leskovšek ◽  
Blaž Leskovar ◽  
Urška Stanković Elesini ◽  
Urška Vrabič-Brodnjak
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Glassy State ◽  
Nanofibrillated Cellulose ◽  
Dynamic Mechanical Properties ◽  
Initial Modulus ◽  
Surface Modified ◽  
Scanning Electron

Polylactic acid (PLA) is one of the most suitable materials for 3D printing. Blending with nanoparticles improves some of its properties, broadening its application possibilities. The article presents a study of composite PLA matrix filaments with added unmodified and lignin/polymerised lignin surface-modified nanofibrillated cellulose (NFC). The influence of untreated and surface-modified NFC on morphological, mechanical, technological, infrared spectroscopic, and dynamic mechanical properties was evaluated for different groups of samples. As determined by the stereo and scanning electron microscopy, the unmodified and surface-modified NFCs with lignin and polymerised lignin were present in the form of plate-shaped agglomerates. The addition of NFC slightly reduced the filaments’ tensile strength, stretchability, and ability to absorb energy, while in contrast, the initial modulus slightly improved. By adding NFC to the PLA matrix, the bending storage modulus (E’) decreased slightly at lower temperatures, especially in the PLA samples with 3 wt% and 5 wt% NFC. When NFC was modified with lignin and polymerised lignin, an increase in E’ was noticed, especially in the glassy state.

scholarly journals Effect of Annealing Process on the Mechanical Properties of X70 Pipeline Steel

2018 ◽  
Vol 186 ◽  
pp. 02001
Author(s):  
Teng-wei Zhu ◽  
Cheng-liang Miao ◽  
Zheng Cheng ◽  
Zhipeng Wang ◽  
Yang Cui ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Annealing Temperature ◽  
Pipeline Steel ◽  
Annealing Process ◽  
X70 Pipeline Steel ◽  
Grain Sizes ◽  
Scanning Electron

The influence of the mechanical properties of X70 pipeline steel under different annealing temperature was studied. The corresponding microstructure was investigated by the Field Emission Scanning Electron Microscopy. The results showed that the yield strength and the tensile strength both experienced from rise to decline with the increase of annealing temperature. The grain sizes were coarse and a large amount of cementite precipitated due to preserving temperature above 550 °, which induced matrix fragmentation and deteriorate the -10 ° DWTT Toughness. There were little changes on the microstructure and mechanical properties when the annealing temperature was under 500 °.

scholarly journals Effect of Different Cooling Regimes on the Mechanical Properties of Cementitious Composites Subjected to High Temperatures

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Jiangtao Yu ◽  
Wenfang Weng ◽  
Kequan Yu
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
High Temperature ◽  
Significant Influence ◽  
Microstructural Characterization ◽  
Cementitious Composite ◽  
Engineered Cementitious Composite ◽  
Before And After ◽  
Scanning Electron

The influence of different cooling regimes (quenching in water and cooling in air) on the residual mechanical properties of engineered cementitious composite (ECC) subjected to high temperature up to 800°C was discussed in this paper. The ECC specimens are exposed to 100, 200, 400, 600, and 800°C with the unheated specimens for reference. Different cooling regimens had a significant influence on the mechanical properties of postfire ECC specimens. The microstructural characterization was examined before and after exposure to fire deterioration by using scanning electron microscopy (SEM). Results from the microtest well explained the mechanical properties variation of postfire specimens.

Analysis of Applicability of the Hollow Carbon Fibres for Self-Repairing Composites

2012 ◽  
Vol 729 ◽  
pp. 246-251 ◽  
Author(s):  
Sándor Kling ◽  
Tibor Czigány
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Tensile Tests ◽  
Single Fibre ◽  
Internal Diameter ◽  
Carbon Fibres ◽  
Hollow Carbon ◽  
Scanning Electron

The geometry and mechanical properties of solid and hollow carbon fibres were investigated by light-and scanning electron microscopy, and by single fibre tensile tests. The hollowness factor of fibres was determined by their external and internal diameter. The tensile strength was determined by single fibre tensile break tests. It was shown that the bigger the diameter of the fibres the lower the mechanical properties is. It was found that the hollow carbon fibres are suitable for preparation of a self-repairing composite with the advantage over other solutions because of their geometrical and mechanical properties.

Microstructures and Mechanical Properties of Melt Spinning Spandex

2014 ◽  
Vol 1048 ◽  
pp. 36-40
Author(s):  
Wei Lai Chen ◽  
Lin Yan Wan ◽  
Hong Qin
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Heat Treatment ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Melt Spinning ◽  
Scanning Electron

Microstructures and mechanical properties of melt spinning spandex were studied in this article.Cross section and longitudinal surface were observed and analyzed by JSM-5610LV scanning electron microscopy. Q2000 DSC differential scanning calorimeter was used to test the glass transition temperature and melting temperature which indicated glass transition temperature is about 44°C and melting temperature is about 200°C. We employed JSM-5610LV scanning electron microscopy to observe adhesion of melt spinning spandex with nylon filament after different time and temperature processing. It concluded that after 150°C90s、160°C60s、160°C90s、170°C30s heat treatment, the adhesive of melt spinning spandex with nylon is good. At the same time,tensile strength and elastic properties of melt spinning spandex which was processed under different time and temperature were tested, tensile strength and elastic recovery of melt spinning spandex after160°C 90s heat treatment is the best.

Effect of Nanocellulose Loading on Tensile Properties of Nitrile Rubber

2017 ◽  
Vol 264 ◽  
pp. 112-115
Author(s):  
Erfan Suryani Abdul Rashid ◽  
Wageeh Abdulhadi Yehye ◽  
Nurhidayatullaili Muhd Julkapli ◽  
Sharifah Bee O.A. Abdul Hamid
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Tensile Test ◽  
Tensile Properties ◽  
Mechanical Performance ◽  
Butadiene Rubber ◽  
Fracture Surfaces ◽  
Scanning Electron

Nanocellulose (NCC) is incorporated into nitrile butadiene rubber (NBR) latex with the composition 0 to 5 phr using dipping method. Mechanical properties of NBR/NCC composites using tensile test was used to characterize their mechanical performance and the fracture surfaces post tensile test were studied. The tensile strength of NBR/NCC composites increase significantly with the addition of nanocellulose. This could be anticipated due to the presence of Van der Waals interaction between hydrophilic natures of nanocellulose with hydrophobic of NBR consequently limits the tearing propagation. The result was supported with the fracture surfaces morphology viewed under Fourier Emission Scanning Electron Microscopy (FESEM).

scholarly journals Simultaneous Improvement in the Tensile and Impact Strength of Polypropylene Reinforced by Graphene

2020 ◽  
Vol 2020 ◽  
pp. 1-5
Author(s):  
Li Juan
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Fracture Surface ◽  
Impact Strength ◽  
Melt Blending ◽  
Elongation At Break ◽  
Morphological Behavior ◽  
Scanning Electron

The nanocomposites of polypropylene (PP)/graphene were prepared by melt blending. The effects of the dosage of graphene on the flow and mechanical properties of the nanocomposites were investigated. The morphologies of fracture surfaces were characterized through scanning electron microscopy (SEM). The graphene simultaneous enhanced tensile and impact properties of nanocomposites. A 3.22% increase in tensile strength, 39.8% increase in elongation at break, and 26.7% increase in impact strength are achieved by addition of only 1 wt.% of graphene loading. The morphological behavior indicates the fracture surface of PP/graphene is more rough than that of pure PP.

scholarly journals Impact of High Temperature on the Compressive Strength of ECC

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Xingyan Shang ◽  
Zhoudao Lu
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Compressive Strength ◽  
High Temperature ◽  
Microstructural Characterization ◽  
Cementitious Composites ◽  
Strengthening Effect ◽  
Before And After ◽  
Scanning Electron

The influence of different cooling regimes (quenching in water and cooling in air) on the residual mechanical properties of ECC (engineered cementitious composites) exposed to high temperature up to 800°C was discussed in this paper. The specimens quenching in water gained better mechanical properties than the ones cooling in air. The strengthening effect of quenching for specimens subjected to 800°C was more significant than for the ones subjected to 400°C. The microstructural characterization is examined before and after exposure to fire deterioration by using scanning electron microscopy. Results from the microtest well explained the mechanical properties variation of postfire specimens.

Microstructure and Mechanical Properties of Titanium Severely Strained by Means of Friction Roll Processing

2007 ◽  
Vol 561-565 ◽  
pp. 909-912 ◽  
Author(s):  
Mei Qin Shi ◽  
Yoshimasa Takayama ◽  
Hajime Kato
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Texture Evolution ◽  
Electron Back Scatter Diffraction ◽  
Subsequent Annealing ◽  
Severe Plastic Deformation Technique ◽  
Before And After ◽  
Feeding Speed ◽  
Scanning Electron

Severe strain has been introduced to commercially purity (CP) titanium samples by means of friction roll processing (FRP), which represents an alternative severe plastic deformation technique by inducing shear strain. FRP has an excellent possibility of controlling surface microstructure combining with subsequent annealing. The resultant microstructure refinement and texture evolution has been investigated. Hardness of sample was measured to compare mechanical properties of samples before and after FRPed. Parameters including the different indentations given to the sample and sample feeding speed were experimentally conducted to find the optimum condition for investigating effect on microstructure evolution. After subsequent annealing, the evolutions of microstructure and texture were observed by field emission scanning electron microscopy (FESEM) and analyzed by scanning electron microscopy/ electron back scatter diffraction pattern (SEM/EBSP) technique. Transverse texture was found to be the preferred orientation existing in the thin top layer of the sample after FRP and annealed at 823K for 1h.

Sign in / Sign up

Export Citation Format

Share Document