A Study on the Electrical Properties of ZnO Based Transparent TFTs

2006 ◽  
Vol 514-516 ◽  
pp. 68-72 ◽  
Author(s):  
Pedro Barquinha ◽  
Elvira Fortunato ◽  
Alexandra Gonçalves ◽  
Ana Pimentel ◽  
António Marques ◽  
...  
Keyword(s):  
Zinc Oxide ◽  
Electrical Characterization ◽  
Channel Mobility ◽  
Grain Sizes ◽  
Different Types ◽  
Effective Saturation ◽  
Materials Used ◽  
Silicon Based ◽  
Nanocrystalline Zinc Oxide ◽  
Output Conductance

The purpose of this work is to present in-depth electrical characterization on transparent TFTs, using zinc oxide produced at room temperature as the semiconductor material. Some of the studied aspects were the relation between the output conductance in the post-pinch-off regime and width-to-length ratios, the gate leakage current, the semiconductor/insulator interface traps density and its relation with threshold voltage. The main point of the analysis was focused on channel mobility. Values extracted using different methodologies, like effective, saturation and average mobility, are presented and discussed regarding their significance and validity. The evolution of the different types of mobility with the applied gate voltage was investigated and the obtained results are somehow in disagreement with the typical behavior found on classical silicon based MOSFETs, which is mainly attributed to the completely different structures of the semiconductor materials used in the two situations: while in MOSFETS we have monocrystalline silicon, our transparent TFTs use poly/nanocrystalline zinc oxide with grain sizes of about 10 nm.

Current Highlights About the Safety of Inorganic Nanomaterials in Healthcare

2019 ◽  
Vol 26 (12) ◽  
pp. 2147-2165 ◽  
Author(s):  
Luana Perioli ◽  
Cinzia Pagano ◽  
Maria Rachele Ceccarini
Keyword(s):  
Zinc Oxide ◽  
Inorganic Material ◽  
Small Dimension ◽  
Inorganic Materials ◽  
Intracellular Space ◽  
Increased Risk ◽  
Inorganic Nanomaterials ◽  
Materials Used ◽  
Health Field ◽  
Fundamental Requirement

: In recent years inorganic materials are largely present in products intended for health care. Literature gives many examples of inorganic materials used in many healthcare products, mainly in pharmaceutical field. : Silver, zinc oxide, titanium oxide, iron oxide, gold, mesoporous silica, hydrotalcite-like compound and nanoclays are the most common inorganic materials used in nanosized form for different applications in the health field. Generally, these materials are employed to realize formulations for systemic use, often with the aim to perform a specific targeting to the pathological site. The nanometric dimensions are often preferred to obtain the cellular internalization when the target is localized in the intracellular space. : Some materials are frequently used in topical formulations as rheological agents, adsorbents, mattifying agents, physical sunscreen (e.g. zinc oxide, titanium dioxide), and others. : Recent studies highlighted that the use of nanosized inorganic materials can represent a risk for health. The very small dimension (nanometric) until a few years ago represented a fundamental requirement; however, it is currently held responsible for the inorganic material toxicity. This aspect is very important to be considered as actually numerous inorganic materials can be found in many products available in the market, often dedicated to infants and children. These materials are used without taking into account their dimensional properties with increased risk for the user/patient. : This review deals with a deep analysis of current researches documenting the toxicity of nanometric inorganic materials especially those largely used in products available in the market.

scholarly journals Biopolymeric Materials Used as Nonviral Vectors: A Review

2021 ◽  
Vol 2 (1) ◽  
pp. 100-109
Author(s):  
Jailson de Araújo Santos ◽  
Daniel Barbosa Liarte ◽  
Alessandra Braga Ribeiro ◽  
Marcia dos Santos Rizzo ◽  
Marcília Pinheiro da Costa ◽  
...  
Keyword(s):  
Chemical Structure ◽  
Web Of Science ◽  
Gene Transfection ◽  
Genetic Material ◽  
Nonviral Vectors ◽  
Cationic Polymers ◽  
Genetic Trait ◽  
Low Diversity ◽  
Different Types ◽  
Materials Used

Bacterial transformation and gene transfection can be understood as being the results of introducing specific genetic material into cells, resulting in gene expression, and adding a new genetic trait to the host cell. Many studies have been carried out to investigate different types of lipids and cationic polymers as promising nonviral vectors for DNA transfer. The present study aimed to carry out a systematic review on the use of biopolymeric materials as nonviral vectors. The methodology was carried out based on searches of scientific articles and applications for patents published or deposited from 2006 to 2020 in different databases for patents (EPO, USPTO, and INPI) and articles (Scopus, Web of Science, and Scielo). The results showed that there are some deposits of patents regarding the use of chitosan as a gene carrier. The 16 analyzed articles allowed us to infer that the use of biopolymers as nonviral vectors is limited due to the low diversity of biopolymers used for these purposes. It was also observed that the use of different materials as nonviral vectors is based on chemical structure modifications of the material, mainly by the addition of cationic groups. Thus, the use of biopolymers as nonviral vectors is still limited to only a few polysaccharide types, emphasizing the need for further studies involving the use of different biopolymers in processes of gene transfer.

scholarly journals Sensing Performance of Al and Sn Doped ZnO for Hydrogen Detection

Proceedings ◽  
2019 ◽  
Vol 14 (1) ◽  
pp. 39
Author(s):  
Zahira. El khalidi ◽  
Maryam Siadat ◽  
Elisabetta. Comini ◽  
Salah. Fadili ◽  
Philippe. Thevenin
Keyword(s):  
Zinc Oxide ◽  
Chemical Sensor ◽  
Low Cost ◽  
Zinc Powder ◽  
Health Condition ◽  
Vibration Modes ◽  
X Ray Diffraction ◽  
Grain Sizes ◽  
Pure Oxide ◽  
Doped Zno

Chemical gas sensors were studied long ago and nowadays, for the advantageous role they provide to the environment, health condition monitoring and protection. The recent studies focus on the semiconductors sensing abilities, especially of non toxic and low cost compounds. The present work describes the steps to elaborate and perform a chemical sensor using intrinsic and doped semiconductor zinc oxide. First, we synthesized pure oxide using zinc powder, then, two other samples were established where we introduced the same doping percentage of Al and Sn respectively. Using low cost spray pyrolysis, and respecting the same conditions of preparation. The obtained samples were then characterized by X Ray Diffraction (XRD) that revealed the hexagonal wurzite structure and higher crystallite density towards the direction (002), besides the appearance of the vibration modes related to zinc oxide, confirmed by Raman spectroscopy. SEM spectroscopy showed that the surface morphology is ideal for oxidizing/reduction reactions, due to the porous structure and the low grain sizes, especially observed for the sample Sn doped ZnO. The gas testing confirms these predictions showing that the highest response is related to Sn doped ZnO compared to ZnO and followed by Al doped ZnO. The films exhibited responses towards: CO, acetone, methanol, H2, ammonia and NO2. The concentrations were varied from 10 to 500 ppm and the working temperatures from 250 to 500°C, the optimal working temperatures were 350 and 400 °C. Sn doped ZnO showed a high response towards H2 gas target, with a sensitivity reaching 200 at 500 ppm, for 400 °C.

scholarly journals Microwave-assisted additive free synthesis of nanocrystalline zinc oxide

2010 ◽  
Vol 203 (2) ◽  
pp. 415-418 ◽  
Author(s):  
Kushal D. Bhatte ◽  
Pawan Tambade ◽  
Shin-ichiro Fujita ◽  
Masahiko Arai ◽  
Bhalchandra M. Bhanage
Keyword(s):  
Zinc Oxide ◽  
Microwave Assisted ◽  
Nanocrystalline Zinc Oxide

scholarly journals Fabrication of Porous Silicon Based Humidity Sensing Elements on Paper

2015 ◽  
Vol 2015 ◽  
pp. 1-10 ◽  
Author(s):  
Tero Jalkanen ◽  
Anni Määttänen ◽  
Ermei Mäkilä ◽  
Jaani Tuura ◽  
Martti Kaasalainen ◽  
...  
Keyword(s):  
Porous Silicon ◽  
Smart Cities ◽  
Low Cost ◽  
Electrical Characterization ◽  
Fabrication Process ◽  
Sensing Element ◽  
Paper Substrate ◽  
Roll To Roll ◽  
Silver Electrodes ◽  
Silicon Based

A roll-to-roll compatible fabrication process of porous silicon (pSi) based sensing elements for a real-time humidity monitoring is described. The sensing elements, consisting of printed interdigitated silver electrodes and a spray-coated pSi layer, were fabricated on a coated paper substrate by a two-step process. Capacitive and resistive responses of the sensing elements were examined under different concentrations of humidity. More than a three orders of magnitude reproducible decrease in resistance was measured when the relative humidity (RH) was increased from 0% to 90%. A relatively fast recovery without the need of any refreshing methods was observed with a change in RH. Humidity background signal and hysteresis arising from the paper substrate were dependent on the thickness of sensing pSi layer. Hysteresis in most optimal sensing element setup (a thick pSi layer) was still noticeable but not detrimental for the sensing. In addition to electrical characterization of sensing elements, thermal degradation and moisture adsorption properties of the paper substrate were examined in connection to the fabrication process of the silver electrodes and the moisture sensitivity of the paper. The results pave the way towards the development of low-cost humidity sensors which could be utilized, for example, in smart packaging applications or in smart cities to monitor the environment.

scholarly journals Demonstration of a Robust All-Silicon-Carbide Intracortical Neural Interface

Micromachines ◽  
2018 ◽  
Vol 9 (8) ◽  
pp. 412 ◽  
Author(s):  
Evans Bernardin ◽  
Christopher Frewin ◽  
Richard Everly ◽  
Jawad Ul Hassan ◽  
Stephen Saddow
Keyword(s):  
Silicon Carbide ◽  
High Performance ◽  
Electrical Characterization ◽  
Electrode Impedance ◽  
Voltage Range ◽  
Promising Solution ◽  
Multiple Materials ◽  
Diode Behavior ◽  
Materials Used ◽  
P Type

Intracortical neural interfaces (INI) have made impressive progress in recent years but still display questionable long-term reliability. Here, we report on the development and characterization of highly resilient monolithic silicon carbide (SiC) neural devices. SiC is a physically robust, biocompatible, and chemically inert semiconductor. The device support was micromachined from p-type SiC with conductors created from n-type SiC, simultaneously providing electrical isolation through the resulting p-n junction. Electrodes possessed geometric surface area (GSA) varying from 496 to 500 K μm2. Electrical characterization showed high-performance p-n diode behavior, with typical turn-on voltages of ~2.3 V and reverse bias leakage below 1 nArms. Current leakage between adjacent electrodes was ~7.5 nArms over a voltage range of −50 V to 50 V. The devices interacted electrochemically with a purely capacitive relationship at frequencies less than 10 kHz. Electrode impedance ranged from 675 ± 130 kΩ (GSA = 496 µm2) to 46.5 ± 4.80 kΩ (GSA = 500 K µm2). Since the all-SiC devices rely on the integration of only robust and highly compatible SiC material, they offer a promising solution to probe delamination and biological rejection associated with the use of multiple materials used in many current INI devices.

scholarly journals Ultrasound assisted additive free synthesis of nanocrystalline zinc oxide

2011 ◽  
Vol 18 (1) ◽  
pp. 54-58 ◽  
Author(s):  
Kushal D. Bhatte ◽  
Shin-Ichiro Fujita ◽  
Masahiko Arai ◽  
Anirudha B. Pandit ◽  
Bhalchandra M. Bhanage
Keyword(s):  
Zinc Oxide ◽  
Ultrasound Assisted ◽  
Nanocrystalline Zinc Oxide
Sign in / Sign up

Export Citation Format

Share Document