Study on Process of Planing Forming of Plate Fin Heat Sinks

2006 ◽  
Vol 532-533 ◽  
pp. 237-240 ◽  
Author(s):  
Zhen Ping Wan ◽  
Yong Tang ◽  
Wen Jun Deng ◽  
Ya Jun Liu
Keyword(s):  
Boundary Layer ◽  
Rough Surface ◽  
Heat Sink ◽  
Thermal Boundary Layer ◽  
Heat Dissipation ◽  
Rake Angle ◽  
Heat Sinks ◽  
Air Cooling ◽  
Transition Area ◽  
On Chip

Primary heat dissipation method of IC Chip is still air-cooling at present. This paper presents a new machining method of air-cooled plate fin heat sinks, namely orthogonal planing. The surface of plate fins machined by this method are rough enough to augment its specific surface area; the rough surface can also disturb laminar sub-layer of turbulent thermal boundary layer, thus the thermal resistances of thermal boundary layer are reduced. Therefore, heat dissipation efficiency of heat sink can be enhanced further. The focus of plate fin heat sinks forming by orthogonal planing is how to machine flat chips. A new pattern of chip curl that is called down-curl can be observed when rake angle of tool is rather large and cutting thickness is very thin. As cutting thickness increases, down-curl chips become flat and then up-curling. There is a transition area that chips are not curled between down- and up-curl. The conditions that chips are not curled are obtained through investigating influences of rake angle and cutting thickness on chip curl, and flat plate fins with rough surface are produced.

Least-Volume Optimization of Finned Heat Sinks for Burn-in Air-Cooling Solutions

2003 ◽  
Author(s):  
Zhaojuan He ◽  
Patrick E. Phelan
Keyword(s):  
Heat Sink ◽  
Heat Dissipation ◽  
Past Research ◽  
Heat Sinks ◽  
Air Cooling ◽  
Electronic Packages ◽  
Pin Fin ◽  
Heat Spreaders ◽  
Forced Air ◽  
Innovative Techniques

With the development and increasing use of high-density components with their high power dissipation needs, electronic packages have required the investigation of innovative techniques for the efficient dissipation of heat. One prevalent method is the use of forced convection heat spreaders, called heat sinks, which are also widely used in Burn-In (BI) ovens. There are some contradictions remaining in recent research on modeling and Nusselt number correlations of heat sinks in forced air convection. This paper begins by reviewing past research for different finned heat sink geometries with and without bypass flow over the heat sinks. A new method called Least Volume Optimization is then proposed to analyze the thermal performance of finned heat sinks for BI air-cooling solutions. The analysis shows that the volumetric heat dissipation of a parallel plate fin heat sink is higher than that of a pin fin heat sink, based on an optimal fin geometry.

CFD Analysis of an Air-Cooled Planar Heat Sink With Cross-Connected Alternating Converging-Diverging Channels

2015 ◽  
Author(s):  
Omer Bugra Kanargi ◽  
Christopher Yap ◽  
Poh Seng Lee
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Heat Sink ◽  
Thermal Boundary Layer ◽  
Reynolds Numbers ◽  
Secondary Flows ◽  
Heat Sinks ◽  
Ansys Fluent ◽  
Diverging Channel ◽  
The Cross

In this study, the thermal and hydraulic performances of an air-cooled planar heat sink with cross-connected alternating converging-diverging channels were investigated. The commercial CFD solver ANSYS Fluent was used to solve the fluid flow and heat transfer from the fins to the air flow for a range of converging-diverging channel expansion ratios, heat generation rates and Reynolds numbers. The converging and diverging channel sections create high and low pressure zones, respectively, in the flow domain and this pressure difference induces secondary flows from the converging channel sections to the diverging channel sections through the cross connections. The observed heat transfer enhancement results from two different phenomena: (1) thermal boundary layer disruption and re-initialization at the cross connections and (2) fluid mixing; where the former reduces the convection resistance in the vicinity of the fin walls by reducing the thermal boundary layer thickness, while the latter allows a more uniform temperature build-up of air in the streamwise direction. Despite the fact that the pressure drop penalty increases due to flow restriction compared to the straight channel heat sinks, it is possible to enhance the Nusselt number for up to 100% with the proposed heat sink design.

Thermal Behaviors of Passively-Cooled Hybrid Fin Heat Sinks for Lightweight and High Performance Thermal Management

2015 ◽  
Author(s):  
Nico Setiawan Effendi ◽  
Kyoung Joon Kim
Keyword(s):  
Thermal Resistance ◽  
Heat Sink ◽  
High Performance ◽  
Heat Dissipation ◽  
Computational Study ◽  
Heat Sinks ◽  
Channel Diameter ◽  
Internal Channel ◽  
Study Results ◽  
Parametric Effects

A computational study is conducted to explore thermal performances of natural convection hybrid fin heat sinks (HF HSs). The proposed HF HSs are a hollow hybrid fin heat sink (HHF HS) and a solid hybrid fin heat sink (SHF HS). Parametric effects such as a fin spacing, an internal channel diameter, a heat dissipation on the performance of HF HSs are investigated by CFD analysis. Study results show that the thermal resistance of the HS increases while the mass-multiplied thermal resistance of the HS decreases associated with the increase of the channel diameter. The results also shows the thermal resistance of the SHF HS is 13% smaller, and the mass-multiplied thermal resistance of the HHF HS is 32% smaller compared with the pin fin heat sink (PF HS). These interesting results are mainly due to integrated effects of the mass-reduction, the surface area enhancement, and the heat pumping via the internal channel. Such better performances of HF HSs show the feasibility of alternatives to the conventional PF HS especially for passive cooling of LED lighting modules.

Design of Optimum Plate-Fin Natural Convective Heat Sinks

2003 ◽  
Vol 125 (2) ◽  
pp. 208-216 ◽  
Author(s):  
Avram Bar-Cohen ◽  
Madhusudan Iyengar ◽  
Allan D. Kraus
Keyword(s):  
Nusselt Number ◽  
Specific Heat ◽  
Rectangular Plate ◽  
Heat Sink ◽  
Heat Dissipation ◽  
Thermal Design ◽  
Heat Sinks ◽  
And Performance ◽  
Nusselt Number Correlation ◽  
The Impact

The effort described herein extends the use of least-material single rectangular plate-fin analysis to multiple fin arrays, using a composite Nusselt number correlation. The optimally spaced least-material array was also found to be the globally best thermal design. Comparisons of the thermal capability of these optimum arrays, on the basis of total heat dissipation, heat dissipation per unit mass, and space claim specific heat dissipation, are provided for several potential heat sink materials. The impact of manufacturability constraints on the design and performance of these heat sinks is briefly discussed.

scholarly journals Mathematical modeling and numerical simulation of heat dissipation in led bulbs

2020 ◽  
Vol 24 (3 Part A) ◽  
pp. 1877-1884 ◽  
Author(s):  
Diego Alarcón ◽  
Eduardo. Balvís ◽  
Ricardo Bendaña ◽  
Alberto Conejero ◽  
de Fernández ◽  
...  
Keyword(s):  
Mathematical Modeling ◽  
Numerical Simulation ◽  
Numerical Simulations ◽  
Heat Sink ◽  
Heat Dissipation ◽  
Thermal Contact ◽  
Heat Sinks ◽  
Experimental Measurements ◽  
Heating And Cooling ◽  
The Common

We present a detailed study of heating and cooling processes in LED luminaires with passive heat sinks. Our analysis is supported by numerical simulations as well as experimental measurements, carried on commercial systems used for outdoor lighting. We have focused our analysis on the common case of a single LED source in thermal contact with an aluminum passive heat sink, obtaining an excellent agreement with experimental measurements and the numerical simulations performed. Our results can be easily expanded, without loss of generality, to similar systems.

Characterization of Light Weight Heat Sink Materials for Thermal Management of Electronics

2007 ◽  
Author(s):  
Tunc Icoz ◽  
Mehmet Arik ◽  
John T. Dardis
Keyword(s):  
Thermal Management ◽  
Heat Sink ◽  
High Efficiency ◽  
Computational Study ◽  
Heat Sinks ◽  
Advanced Materials ◽  
Air Cooling ◽  
Thermal Management Of Electronics ◽  
Thermal Solution

Thermal management of electronics is a critical part of maintaining high efficiency and reliability. Adequate cooling must be balanced with weight and volumetric requirements, especially for passive air-cooling solutions in electronics applications where space and weight are at a premium. It should be noted that there are systems where thermal solution takes more than 95% of the total weight of the system. Therefore, it is necessary to investigate and utilize advanced materials to design low weight and compact systems. Many of the advanced materials have anisotropic thermal properties and their performances depend strongly on taking advantage of superior properties in the desired directions. Therefore, control of thermal conductivity plays an important role in utilization of such materials for cooling applications. Because of the complexity introduced by anisotropic properties, thermal performances of advanced materials are yet to be fully understood. Present study is an experimental and computational study on characterization of thermal performances of advanced materials for heat sink applications. Numerical simulations and experiments are performed to characterize thermal performances of four different materials. An estimated weight savings in excess of 75% with lightweight materials are observed compared to the traditionally used heat sinks.

scholarly journals Numerical and Experimental Investigation of Air Cooling for Photovoltaic Panels Using Aluminum Heat Sinks

2020 ◽  
Vol 2020 ◽  
pp. 1-9 ◽  
Author(s):  
Zainal Arifin ◽  
Dominicus Danardono Dwi Prija Tjahjana ◽  
Syamsul Hadi ◽  
Rendy Adhi Rachmanto ◽  
Gabriel Setyohandoko ◽  
...  
Keyword(s):  
Heat Sink ◽  
Cfd Simulation ◽  
Operating Temperature ◽  
Ambient Air ◽  
Heat Sinks ◽  
Solar Irradiation ◽  
Electrical Performance ◽  
Electricity Production ◽  
Air Cooling ◽  
Pv Panel

An increase in the operating temperature of photovoltaic (PV) panels caused by high levels of solar irradiation can affect the efficiency and lifespan of PV panels. This study uses numerical and experimental analyses to investigate the reduction in the operating temperature of PV panels with an air-cooled heat sink. The proposed heat sink was designed as an aluminum plate with perforated fins that is attached to the back of the PV panel. A comprehensive computational fluid dynamics (CFD) simulation was conducted using the software ANSYS Fluent to ensure that the heat sink model worked properly. The influence of heat sinks on the heat transfer between a PV panel and the circulating ambient air was investigated. The results showed a substantial decrease in the operating temperature of the PV panel and an increase in its electrical performance. The CFD analysis in the heat sink model with an air flow velocity of 1.5 m/s and temperature of 35°C under a heat flux of 1000 W/m2 showed a decrease in the PV panel’s average temperature from 85.3°C to 72.8°C. As a consequence of decreasing its temperature, the heat sink increased the open-circuit photovoltage (VOC) and maximum power point (PMPP) of the PV panel by 10% and 18.67%, respectively. Therefore, the use of aluminum heat sinks could provide a potential solution to prevent PV panels from overheating and may indirectly lead to a reduction in CO2 emissions due to the increased electricity production from the PV system.

A Study of Forced Convection Direct Air Cooling in the Downstream Vicinity of Heat Sinks

1990 ◽  
Vol 112 (3) ◽  
pp. 234-240 ◽  
Author(s):  
G. L. Lehmann ◽  
S. J. Kosteva
Keyword(s):  
Heat Transfer ◽  
Forced Convection ◽  
Heat Sink ◽  
Convection Heat Transfer ◽  
Heat Sinks ◽  
Air Cooling ◽  
Transfer Coefficients ◽  
Packaging System ◽  
Transfer Rates ◽  
Heat Transfer Coefficients

An experimental study of forced convection heat transfer is reported. Direct air cooling of an electronics packaging system is modeled by a channel flow, with an array of uniformly sized and spaced elements attached to one channel wall. The presence of a single or complete row of longitudinally finned heat sinks creates a modified flow pattern. Convective heat transfer rates at downstream positions are measured and compared to that of a plain array (no heat sinks). Heat transfer rates are described in terms of adiabatic heat transfer coefficients and thermal wake functions. Empirical correlations are presented for both variations in Reynolds number (5000 < Re < 20,000) and heat sink geometry. It is found that the presence of a heat sink can both enhance and degrade the heat transfer coefficient at downstream locations, depending on the relative position.

Experimental Investigation of a PCM-Based Topology Optimized Heat Sink for Passive Cooling of Electronics

2020 ◽  
Author(s):  
Jin Yao Ho ◽  
Kai Choong Leong
Keyword(s):  
Thermal Performance ◽  
Heat Sink ◽  
Heat Dissipation ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Heat Fluxes ◽  
Heat Sinks ◽  
Base Temperature ◽  
Storage Unit ◽  
Cooling Of Electronics

Abstract A thermal energy storage unit filled with phase change material (PCM) can serve as a heat sink for the cooling of electronics with intermittent or periodic heat dissipation rates. The use of thermal conductive structures (TCS) is an effective method of improving the thermal performance of a PCM-based heat sink. In this paper, topology optimization is explored to develop a new class of TCS with a tree-like structure to enhance the thermal performance of a trapezoidal heat sink. The topology-optimized heat sink was then fabricated by Selective Laser Melting (SLM) using an aluminum alloy, AlSi10Mg, as the base powder. Experiments were performed to evaluate the thermal performance of the topology-optimized heat sink with the tree-like structure. In addition, a conventional longitudinal-fin heat sink of the same solid volume fraction (φ = 16.2%) and a heat sink without enhanced structure were also fabricated and experimentally investigated for comparison. Rubitherm RT-35HC paraffin wax was used as the PCM. Three different heat fluxes of 4.00 kW/m2, 5.08 kW/m2 and 7.24 kW/m2 were applied at the base of each specimen by a silicone rubber heater. The structure wall and the PCM temperatures were measured over time. Our results show that, for all heat rates tested, the topology-optimized heat sink was able to maintain a lower base temperature as compared to the fin-structure and the plain heat sinks. A thermal enhancement ratio (ε) is defined to evaluate the performance of the heat sinks with and without the use of PCM. From the experimental results, the highest ε value of 8.6 was achieved by the topology-optimized heat sink. These results indicate the better performance of the topology-optimized heat sink in dissipating heat as compared to the other specimens.

Enabling Thermal Management of High-Powered Server Processors Using Passive Thermosiphon Heat Sink

2019 ◽  
Author(s):  
Devdatta P. Kulkarni ◽  
Priyanka Tunuguntla ◽  
Guixiang Tan ◽  
Casey Carte
Keyword(s):  
Heat Pipe ◽  
High Power ◽  
Heat Sink ◽  
Capital Investment ◽  
Thermal Design ◽  
Heat Sinks ◽  
Air Cooling ◽  
Liquid Cooling ◽  
Two Phase ◽  
Pipe Heat

Abstract In recent years, rapid growth is seen in computer and server processors in terms of thermal design power (TDP) envelope. This is mainly due to increase in processor core count, increase in package thermal resistance, challenges in multi-chip integration and maintaining generational performance CAGR. At the same time, several other platform level components such as PCIe cards, graphics cards, SSDs and high power DIMMs are being added in the same chassis which increases the server level power density. To mitigate cooling challenges of high TDP processors, mainly two cooling technologies are deployed: Liquid cooling and advanced air cooling. To deploy liquid cooling technology for servers in data centers, huge initial capital investment is needed. Hence advanced air-cooling thermal solutions are being sought that can be used to cool higher TDP processors as well as high power non-CPU components using same server level airflow boundary conditions. Current air-cooling solutions like heat pipe heat sinks, vapor chamber heat sinks are limited by the heat transfer area, heat carrying capacity and would need significantly more area to cool higher TDP than they could handle. Passive two-phase thermosiphon (gravity dependent) heat sinks may provide intermediate level cooling between traditional air-cooled heat pipe heat sinks and liquid cooling with higher reliability, lower weight and lower cost of maintenance. This paper illustrates the experimental results of a 2U thermosiphon heat sink used in Intel reference 2U, 2 node system and compare thermal performance using traditional heat sinks solutions. The objective of this study was to showcase the increased cooling capability of the CPU by at least 20% over traditional heat sinks while maintaining cooling capability of high-power non-CPU components such as Intel’s DIMMs. This paper will also describe the methodology that will be used for DIMMs serviceability without removing CPU thermal solution, which is critical requirement from data center use perspective.

Sign in / Sign up

Export Citation Format

Share Document