A Miniature Energy Harvesting Device Using Martensite Variant Reorientation

2013 ◽  
Vol 738-739 ◽  
pp. 411-415 ◽  
Author(s):  
Manfred Kohl ◽  
Rui Zhi Yin ◽  
Viktor Pinneker ◽  
Yossi Ezer ◽  
Alexei Sozinov
Keyword(s):  
Magnetic Field ◽  
Energy Harvesting ◽  
Magnetic Flux ◽  
Output Voltage ◽  
Permanent Magnets ◽  
Magnetic Circuit ◽  
Compressive Loading ◽  
Piezoelectric Bimorph ◽  
Martensite Variant ◽  
Cyclic Motion

This paper presents a miniature energy harvesting device that makes use of stress-induced cyclic martensite variant reorientation in a Ni-Mn-Ga single crystal of 0.3x2x2 mm³ size. The stress- and magnetic field-induced reorientation is investigated for single crystalline Ni50.2Mn28.4Ga21.4 specimens of 0.3 mm thickness that are cut along the (100) direction and subjected to uniaxial compressive loading. A demonstrator is presented consisting of a FSMA specimen placed in the gap of a magnetic circuit to guide and enhance the field of biasing permanent magnets. The cyclic motion of a piezoelectric bimorph actuator is used to mechanically load the FSMA specimen. The corresponding change of magnetic flux induces an electrical voltage in a pick-up coil (N=2000 turns). The effects of biasing magnetic field, strain amplitude and strain velocity are investigated. An optimum magnetic field of 0.4 T exists, where the output voltage reaches 120 mV at a strain velocity of 0.006 ms-1.

scholarly journals Design of a New 1D Halbach Magnet Array with Good Sinusoidal Magnetic Field by Analyzing the Curved Surface

Sensors ◽  
2021 ◽  
Vol 21 (7) ◽  
pp. 2522
Author(s):  
Guangdou Liu ◽  
Shiqin Hou ◽  
Xingping Xu ◽  
Wensheng Xiao
Keyword(s):  
Magnetic Field ◽  
Magnetic Flux ◽  
Permanent Magnet ◽  
Flux Density ◽  
Permanent Magnets ◽  
Air Gap ◽  
Curved Surface ◽  
Magnetic Flux Density ◽  
Sinusoidal Magnetic Field ◽  
The Magnetic Field

In the linear and planar motors, the 1D Halbach magnet array is extensively used. The sinusoidal property of the magnetic field deteriorates by analyzing the magnetic field at a small air gap. Therefore, a new 1D Halbach magnet array is proposed, in which the permanent magnet with a curved surface is applied. Based on the superposition of principle and Fourier series, the magnetic flux density distribution is derived. The optimized curved surface is obtained and fitted by a polynomial. The sinusoidal magnetic field is verified by comparing it with the magnetic flux density of the finite element model. Through the analysis of different dimensions of the permanent magnet array, the optimization result has good applicability. The force ripple can be significantly reduced by the new magnet array. The effect on the mass and air gap is investigated compared with a conventional magnet array with rectangular permanent magnets. In conclusion, the new magnet array design has the scalability to be extended to various sizes of motor and is especially suitable for small air gap applications.

Platform Design for Characterizing Shear Force Produced by Magnetized Magnetorheological Fluid

2019 ◽  
Author(s):  
Ping-Hsun Lee ◽  
Jen-Yuan (James) Chang
Keyword(s):  
Magnetic Field ◽  
Magnetic Flux ◽  
Yield Stress ◽  
Flux Density ◽  
Shear Force ◽  
Permanent Magnets ◽  
Magnetic Flux Density ◽  
Finite Element Method Result ◽  
Mr Fluid ◽  
The Magnetic Field

Abstract In this paper we proposed a platform for measuring shear force of magnetorheological (MR) fluid by which the relationship of yield stress and magnetic flux density of specific material can be determined. The device consisted of a rotatable center tube in a frame body and the magnetic field was provided by two blocks of permanent magnets placed oppositely outside the frame body. The magnitude and direction of the magnetic field were manipulated by changing the distance of the two permanent magnets from the frame body and rotating the center tube, respectively. For determining the magnetic field of the device, we adopted an effective method by fitting the FEM (finite element method) result to the measured one and then rebuilt the absent components to approximate the magnetic field, which was hardly to be measured simultaneously as different device setup were required. With the proposed platform and analytical methods, the drawing shear force and the corresponding yield stress contributed by MR fluid could be evaluated in respect to the magnitude and direction of given magnetic flux density with acceptable accuracy for specific designing purposes without a large, complex, and expensive instrument.

A Mathematical Model of a Modified Voice Coil Energy Harvester

2011 ◽  
Author(s):  
Alireza Hekmati ◽  
Siamak Arzanpour
Keyword(s):  
Magnetic Field ◽  
Magnetic Flux ◽  
Flux Density ◽  
Peak Power ◽  
Magnetic Field Intensity ◽  
Magnetic Circuit ◽  
Magnetic Flux Density ◽  
Magnetic Conductor ◽  
Magnetic Circuits ◽  
The Magnetic Field

This paper presents a mathematical modeling of a modified voice coil generator, which consists of a moving coil within a fixed magnetic circuit. The simulation has been done with Comsol Multiphysics software, which is a powerful tool to demonstrate the pattern of magnetic field and calculate the induced current in the coil. In our simulations, the magnetic circuit consists of the magnetic conductor and the air gap. In this analysis, the magnetic flux density and the magnetic field intensity are calculated. Moreover, through calculation of the total reluctance of the magnetic circuit and employing the ohm’s law for magnetic circuits, the effect of the length and cross section of the total circuit on the magnetic flux are investigated. Finally, a pattern for the magnetic flux density are demonstrated and the simulation result indicates that the magnetic field is well concentrated on the coil area, therefore this prototype can capture and convert most of the kinetic energy to electricity. A prototype has been fabricated and tested on the shaker. The experimental results indicate that this setup is able to produce the maximum voltage of 0.326 V and the peak power equal to 2.605 mW in 35 Hz frequency and 1 mm peak to peak amplitude.

Nondestructive testing of turbine disk roots using solid-state GMR sensor arrays and an axial directional scanning system

2020 ◽  
Vol 64 (1-4) ◽  
pp. 525-531
Author(s):  
Juhyeon Park ◽  
Hoyong Lee ◽  
Gyejo Jung ◽  
Jinyi Lee
Keyword(s):  
Magnetic Field ◽  
Nondestructive Testing ◽  
Magnetic Flux ◽  
Permanent Magnets ◽  
Turbine Disk ◽  
Magnetic Sensors ◽  
Magnetic Flux Leakage ◽  
Scanning System ◽  
Sensor Probe ◽  
Flux Leakage

A nondestructive testing device, consisting of a scanner and signal processing circuits was developed to detect cracks in turbine disk roots. The scanner consists of a longitudinal feeder and a fir-tree-shaped sensor probe. The feeder inserted the sensor probe along the grooves of the turbine blade attachment. Meanwhile, permanent magnets were placed in opposite direction, to generate a closed magnetic field between the magnetic sensors located on the crests of the sensor probe. The fatigue crack in the turbine disk root occurred in the circumferential direction of the turbine. As a result, magnetic flux leakage was caused by disturbing the flow of closed magnetic field by permanent magnets. The magnetic flux leakage was measured by a magnetic sensor. The effectiveness of the proposed device has been verified using artificial defects introduced into the turbine disk roots by electric discharge machining.

scholarly journals Effect of Pole Shoe Design on Inclination Angle of Different Magnetic Fields in Permanent Magnet Machines

Energies ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2437
Author(s):  
Jonathan Sjölund ◽  
Sandra Eriksson
Keyword(s):  
Magnetic Field ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Field Strength ◽  
Magnetic Flux ◽  
Permanent Magnet ◽  
Magnetic Circuit ◽  
Magnetic Flux Density ◽  
Element Analysis ◽  
Inclination Angles

Electromagnetic modelling of electrical machines through finite element analysis is an important design tool for detailed studies of high resolution. Through the usage of finite element analysis, one can study the electromagnetic fields for information that is often difficult to acquire in an experimental test bench. The requirement for accurate result is that the magnetic circuit is modelled in a correct way, which may be more difficult to maintain for rare earth free permanent magnets with an operating range that is more likely to be close to non-linear regions for the relation between magnetic flux density and magnetic field strength. In this paper, the inclination angles of the magnetic flux density, magnetic field strength and magnetization are studied and means to reduce the inclination angles are investigated. Both rotating and linear machines are investigated in this paper, with different current densities induced in the stator windings. By proper design of the pole shoes, one can reduce the inclination angles of the fields in the permanent magnet. By controlling the inclination angles, one can both enhance the performance of the magnetic circuit and increase the accuracy of simpler models for permanent magnet modelling.

scholarly journals Analysis of Effect of the Magnetization Distribution of Multi-Pole PM on SPMSM Performance Using Equivalent Magnetic Circuit Considering Dead Zone

Energies ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3279
Author(s):  
Jae-Hyun Kim ◽  
Kyoung-Soo Cha ◽  
Sung-Woo Hwang ◽  
Soo-Gyung Lee ◽  
Min-Ro Park ◽  
...  
Keyword(s):  
Magnetic Flux ◽  
Flux Density ◽  
Permanent Magnets ◽  
Magnetic Circuit ◽  
Dead Zone ◽  
Magnetic Flux Density ◽  
Magnetization Distribution ◽  
Permanent Magnet Synchronous Motors ◽  
Element Analysis ◽  
The Dead

In multi-pole permanent magnets (PMs) such a ring-type PMs, as multi-poles are magnetized in one segment, the ends of each pole are weakly magnetized, which is known as the dead zone. Thus, when analyzing characteristics of the motor with multi-pole PMs, accurate results can be obtained by considering the magnetization distribution. For this reason, this paper proposed an equivalent magnetic circuit (EMC) for external-rotor surface-mounted permanent magnet synchronous motors (SPMSMs) considering the dead zone to analyze the effects of the dead zone on the characteristics of the motor. As the magnetization in the dead zone gradually decreases toward the end of the pole, the magnetization distribution is assumed to have a trapezoidal shape. To describe the magnetization distribution, each pole was divided into several elements, and the equivalent residual magnetic flux density was applied to the elements of the dead zone. Finally, the validity of the proposed EMC was verified by comparing the back electro-motive force and air-gap magnetic flux density obtained by the EMC, finite-element analysis, and test.

scholarly journals Design of Magnetic Circuit for Stationary Plasma Thruster

2021 ◽  
Vol 2070 (1) ◽  
pp. 012032
Author(s):  
Syed Abdul Lateef ◽  
A.T. Sriram ◽  
M. Murali Krishnan ◽  
A. Sivathanu Pillai
Keyword(s):  
Magnetic Field ◽  
Magnetic Flux ◽  
Flux Density ◽  
Hollow Cathode ◽  
Magnetic Circuit ◽  
Ionization Rate ◽  
Magnetic Flux Density ◽  
Exit Plane ◽  
Radial Magnetic Field ◽  
Magnetic Poles

Abstract SPT-100 electrostatic thruster is considered, and the effects of magnetic circuit is studied by introducing magnetic screen. The magnetic flux density in the discharge channel is generated with the help of one inner coil and four outer coils. The radial magnetic field has to be maximum near the exit plane of the thruster to trap the electrons in acceleration region which are emitted from an external hollow cathode. These electrons help in increasing the ionization rate of the propellant gas. This is obtained by placing magnetic poles near exit plane. It helps to traps the electrons emitted from the external hollow cathode. The magnetic circuit should be designed such that the magnetic flux density is near to zero at the anode plane to reduce interaction of electrons with channel walls. To arrive at such better design, magnetic screens are used. Computational simulations are performed to quantify the magnetic flux density distribution along the channel using COMSOL Multiphysics software. The simulation results show that the obtained radial magnetic flux density is maximum near the exit plane, and the magnetic screens help in reducing the magnetic field at the anode region while maintaining the maximum magnetic field at the exit plane.

scholarly journals Method of parametric analysis of reciprocating electric generators with permanent magnets

2021 ◽  
Vol 66 (4) ◽  
pp. 458-469
Author(s):  
A. B. Menzhinski ◽  
A. N. Malashin ◽  
A. E. Kaleda
Keyword(s):  
Magnetic Field ◽  
Specific Gravity ◽  
Parametric Analysis ◽  
Permanent Magnets ◽  
Magnetic Circuit ◽  
Magnetic System ◽  
Reciprocating Motion ◽  
Electromagnetic Calculation ◽  
Electric Generators ◽  
The Magnetic Field

A method for the parametric analysis of electric generators of reciprocating motion with permanent magnets has been developed, which allows revealing the values of the parameters of the magnetic circuit (cross-sectional area) and the working winding (number of turns) at a given value of the efficiency, providing a minimum specific gravity of the generator. The method of parametric analysis of electric generators of reciprocating motion with permanent magnets consists of three stages. The first and second stages are the electromagnetic calculation of the generator: at the first stage, the main geometric dimensions of the magnetic system and the parameters of the working winding of the generator are determined; at the second stage, the verification of the electromagnetic calculation of the generator, calculation of the nominal mode, calculation of the efficiency and assessment of the thermal state of the generator are fulfilled. At the third stage, a parametric analysis of electric generators of reciprocating motion with permanent magnets with specified constraints is carried out, as well as the refinement of the geometric dimensions and configuration of the magnetic system of the generator using a two-dimensional finite element model of the magnetic field. As a result, to ensure better use of the electrical steel of the magnetic circuit of the generator and thereby reduce its mass, the most saturated areas and areas, which are characterized by low values of the magnetic field strength, are determined. Distinctive features of the proposed technique are: the use of a minimum specific gravity of electric generators of reciprocating motion with longitudinal, transverse or combined changes in the magnetic flux passing through the working winding as an objective function; combined approach to electromagnetic calculation; taking into account the influence of the operating temperature on the parameters of the permanent magnet, as well as overheating of individual parts of the generator.

scholarly journals The Innovative Design of Deep In Situ Pressure Retained Coring Based on Magnetic Field Trigger Controller

2020 ◽  
Vol 2020 ◽  
pp. 1-15
Author(s):  
Guikang Liu ◽  
Mingzhong Gao ◽  
Zhiwen Yang ◽  
Ling Chen ◽  
Maoquan Fu ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Magnetic Flux ◽  
Flux Density ◽  
Magnetic Force ◽  
Magnetic Circuit ◽  
Minimum Condition ◽  
Magnetic Flux Density ◽  
Valve Seat ◽  
Deep Rock

Deep rock mass theory has not yet been completely established, which leads to a lack of theoretical guidance for deep resource development and poor continuity among engineering activities. The foundation of deep rock mechanics theory is to achieve the deep in situ rock fidelity coring (including the retaining of the pore pressure and temperature). To realize this, pressure-retaining coring technology is required. A self-triggered pressure-retaining controller based on magnetic control is proposed in this paper. The pressure-retaining controller realizes pressure-retaining coring in any direction by triggering the closure of the valve cover by a magnetic force, forming a magnetic seal. Fifteen combined magnetic circuit design schemes are proposed. The magnetic flux density norm distribution and magnetic force evolution law of different schemes are then quantitatively analyzed by the finite element method. The results show that a complex magnetization combination can weaken the nonlinear negative correlation between the magnetic force and distance. The optimal design of the valve seat magnetic circuit is Scheme 9, with the valve seat consisting of four shape identical tile magnets. Among the schemes, for Scheme 9, the magnetic flux density norm of the valve cover is the most concentrated. The maximum magnetic flux density norm is in the middle, and the magnetic force at 35 mm from the valve cover to the valve seat is 2.915 N. Scheme 9 satisfies the minimum condition of the mechanical model and verifies the feasibility of magnetic field triggering. This research can be used to gain a better understanding of deep Earth properties and provides technology for the improved design of deep in situ pressure-retaining coring devices.

Study on Magnetic Field for Navigation of Articulated Needle

2012 ◽  
Vol 152-154 ◽  
pp. 952-957
Author(s):  
Hua Fang Huang ◽  
Yi Zhong Wang ◽  
Zong Guo Zhou ◽  
Yong Hua Chen
Keyword(s):  
Magnetic Field ◽  
Magnetic Flux ◽  
Flux Density ◽  
Permanent Magnets ◽  
Dimensional Space ◽  
Three Dimensional ◽  
Magnetic Flux Density ◽  
Variable Direction ◽  
The Magnetic Field ◽  
Three Dimensional Space

When the magnetic articulated needle is inserting, the magnetic field which can produce the magnetic force of variable direction is required in order to implement the magnetic navigation in three-dimensional space. The paper puts forward a method for generating three-dimensional magnetic field based on the rotaion and translation of multiple permanent magnets. In this method, multiple permanent magnets form a circumference array. Every permanent magnet can rotate around the spin axis of itself in the array plane and move along the direction vertical to the array plane. Thus, in the array center, a magnetic fied which can produce the uniform magnetic flux density is obtained. The direction of magnetic fied is controllable in three-dimensional space and the magnitude of magnetic flux density is variable in a certain range. The simulations by ANSYS verify the feasibility of the proposed method.

Sign in / Sign up

Export Citation Format

Share Document