Plasma-MIG Hybrid Welding Process of 5083 Marine Aluminum Alloy

2016 ◽  
Vol 850 ◽  
pp. 519-525 ◽  
Author(s):  
De Tao Cai ◽  
Shan Guo Han ◽  
Shi Da Zheng ◽  
De Jun Yan ◽  
Jiu Qiang Luo ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Aluminum Alloy ◽  
Weld Joint ◽  
Room Temperature ◽  
Welding Process ◽  
Bending Test ◽  
Hybrid Welding ◽  
Plasma Current ◽  
Mig Welding ◽  
Bending Properties

Plasma-MIG hybrid welding and MIG welding of 5083 marine aluminum alloy was carried out. The influences of parameters of welding process on the weldments morphology were investigated in order to optimize the welding process parameters. The macrostructure, microstructure, tensile and bending properties of the optimized joint were studied. The results show that Plasma-MIG hybrid welding not only has a synergistic effect of Plasma and MIG welding but also has a high welding efficiency. Welding speed, Plasma current and MIG current have a significant effect on welding penetration and welding morphology. Meanwhile, the ductility and strength property of weld joint was qualified though the bending test and tensile test. The average tensile strength of weld joint is about 285MPa at room temperature, about 86% of the base metal.

scholarly journals Comparative in Mechanical Behavior of 6061 Aluminum Alloy Welded by Pulsed GMAW with Different Filler Metals and Heat Treatments

Materials ◽  
2019 ◽  
Vol 12 (24) ◽  
pp. 4157 ◽  
Author(s):  
Isidro Guzmán ◽  
Everardo Granda ◽  
Jorge Acevedo ◽  
Antonia Martínez ◽  
Yuliana Dávila ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Tensile Strength ◽  
Aluminum Alloy ◽  
Weld Joint ◽  
Welding Process ◽  
Mechanical Resistance ◽  
6061 Aluminum Alloy ◽  
Β Phase ◽  
Welding Processes ◽  
Filler Metals

Precipitation hardening aluminum alloys are used in many industries due to their excellent mechanical properties, including good weldability. During a welding process, the tensile strength of the joint is critical to appropriately exploit the original properties of the material. The welding processes are still under study, and gas metal arc welding (GMAW) in pulsed metal-transfer configuration is one of the best choices to join these alloys. In this study, the welding of 6061 aluminum alloy by pulsed GMAW was performed under two heat treatment conditions and by using two filler metals, namely: ER 4043 (AlSi5) and ER 4553 (AlMg5Cr). A solubilization heat treatment T4 was used to dissolve the precipitates of β”- phase into the aluminum matrix from the original T6 heat treatment, leading in the formation of β-phase precipitates instead, which contributes to higher mechanical resistance. As a result, the T4 heat treatment improves the quality of the weld joint and increases the tensile strength in comparison to the T6 condition. The filler metal also plays an important role, and our results indicate that the use of ER 4043 produces stronger joints than ER 4553, but only under specific processing conditions, which include a moderate heat net flux. The latter is explained because Mg, Si and Cu are reported as precursors of the production of β”- phase due to heat input from the welding process and the redistribution of both: β” and β precipitates, causes a ductile intergranular fracture near the heat affected zone of the weld joint.

Comparison between Plasma-MIG and MIG Procedures on 5A06 Aluminum Alloy

2008 ◽  
Vol 575-578 ◽  
pp. 1382-1388 ◽  
Author(s):  
Hong Ming Gao ◽  
Yan Bai ◽  
Lin Wu
Keyword(s):  
Tensile Strength ◽  
Aluminum Alloy ◽  
Mechanical Performance ◽  
Weld Zone ◽  
Welding Process ◽  
Deposition Efficiency ◽  
Eutectic Structure ◽  
Melting Rate ◽  
Mig Welding ◽  
5A06 Aluminum Alloy

10mm-5A06 aluminum alloy was butt-welded in a single pass by the plasma-gas metal arc (plasma-MIG) welding procedure, the joints were subjected to X-ray inspection, the microstructure and mechanical performance of weld were also studied. The results indicate that plasma-MIG welding is superior to regular conventional MIG welding on the aspects of reducing weld porosity, increasing joint quality and improving deposition efficiency. Good weld joint with less porosity and excellent mechanical properties is obtained, which can reach as 92.62% tensile strength and 85.12% elongation percentage as base metal. Dimples in which the precipitated phase is the solid solution based on Al3Mg2 are observed in fracture scanning electron micrograph and the fracture mode is ductile rupture. α-Al and Al3Mg2 ,α-Al and eutectic structure are observed respectively in fusion area and in weld zone. The wire feed rate and melting rate can come to 14.5m/min and 80g/min respectively for the 1.6mm welding wire by the plasma-MIG welding process on the premise that the tensile strength of the joints meet the requirements.

scholarly journals Double-Pulse Triple-Wire MIG Welding of 6082-T6 Aluminum Alloy: Process Characteristics and Joint Performances

Metals ◽  
2021 ◽  
Vol 11 (9) ◽  
pp. 1388
Author(s):  
Ke Yang ◽  
Fei Wang ◽  
Hongbing Liu ◽  
Peng Wang ◽  
Chuanguang Luo ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Aluminum Alloy ◽  
High Efficiency ◽  
Welding Process ◽  
Pulse Frequency ◽  
Double Pulse ◽  
Fish Scale ◽  
Mig Welding ◽  
Process Characteristics ◽  
Pulse Welding

High-efficiency and high-quality welding has always been the focus of welding research. This article proposes a novel double-pulse, triple-wire MIG welding process for the welding of 6082-T6 aluminum alloy. The process characteristics of welding arc and droplet transfer were studied, and the performances of weld formation, morphology, hardness, and tensile strength were tested for the 1 Hz, 3 Hz, and 5 Hz double-pulse welding and normal-pulse welding. It was found that in the welding process, the pulsed arc steadily alternated among three welding wires without arc interruption, and the arc length changed periodically with the double-pulse frequency. The droplets transferred with a stable one-pulse-one-drop mode. Besides, a proper double-pulse frequency, e.g., 3 Hz in this case, was conducive to forming good welds with regular fish-scale patterns and no pores. The tensile strength of the joint could reach 64% of the base material’s tensile strength, and its fracture belonged to plastic fracture, which occurred in the HAZ. This new welding method will have great potential in aluminum alloy welding.

scholarly journals Study the Effect of Welding Heat Input on the Microstructure, Hardness, and Impact Toughness of AISI 1015 Steel

2018 ◽  
Vol 14 (1) ◽  
pp. 118-127 ◽  
Author(s):  
Emad Kh. Hamd ◽  
Abbas Sh. Alwan ◽  
Ihsan Khalaf Irthiea
Keyword(s):  
Corrosion Rate ◽  
Weld Joint ◽  
Heat Input ◽  
Plate Thickness ◽  
Welding Process ◽  
Welding Current ◽  
Low Carbon ◽  
Mig Welding ◽  
The Impact ◽  
Weld Heat

In the present study, MIG welding is carried out on low carbon steel type (AISI 1015) by using electrode ER308L of 1.5mm diameter with direct current straight polarity (DCSP). The joint geometry is of a single V-butt joint with one pass welding stroke for different plate thicknesses of 6, 8, and 10 mm. In welding experiments, AISI 1015 plates with dimensions of 200×100mm and edge angle of 60o from both sides are utilized. In this work, three main parameters related to MIG welding process are investigated, which are welding current, welding speed, heat input and plate thickness, and to achieve that three groups of plates are employed each one consists of three plates. The results indicate that increasing the weld heat input (through changing the current and voltage) leads to an increase in widmanstatten ferrite (WF), acicular ferrite (AF) and polygonal ferrite (PF) in FZ region, and a reduction in grain size. It is observed that the micro-hardness of welded AISI 1015 plate increases as the weld heat input decreases. As well as increasing the weld heat input results in an increase in the width of WM and HAZ and a reduction in the impact energy of the weld joint of AISI 1015 at WM region. Also, it is noted the corrosion rate of weld joint increases with increase of Icorr due to increasing in welding current (heat input), corrosion rate increased up to (0.126µm/yr.) with increasing of heat input up to (1.27 KJ/mm).  

Effect of shielding gas flow on welding process of laser-arc hybrid welding and MIG welding

2019 ◽  
Vol 38 ◽  
pp. 530-542 ◽  
Author(s):  
Xiaoyi Yang ◽  
Hui Chen ◽  
Zongtao Zhu ◽  
Chuang Cai ◽  
Chengzhu Zhang
Keyword(s):  
Gas Flow ◽  
Welding Process ◽  
Hybrid Welding ◽  
Mig Welding ◽  
Shielding Gas

Simulation on Temperature and Residual Stress Field of Laser-MIG Hybrid Welding of A6N01-T5 Alloy

2011 ◽  
Vol 399-401 ◽  
pp. 2040-2043 ◽  
Author(s):  
Da Li ◽  
Hua Ji ◽  
Yan Liu ◽  
Guo Qing Gou ◽  
Hui Chen ◽  
...  
Keyword(s):  
Residual Stress ◽  
Aluminum Alloy ◽  
Stress Field ◽  
Welded Joints ◽  
Hybrid Welding ◽  
Mig Welding ◽  
Residual Stress Field ◽  
Heat Cycling

MIG welding and laser-MIG hybrid welding have been widely used to joint aluminum alloy in recent years. Residual stress and heat cycling of MIG welding and laser-MIG hybrid welding are analyzed by SYSWELD software. The results show that the peak values of the stress in hybrid welding is 30~50% less than the results in the MIG welded joints.

Heat Transfer Simulations and Analysis of Joint Cross-Sectional Microstructure on Friction Stir Welding between Steel and Aluminium

2020 ◽  
Vol 863 ◽  
pp. 85-95
Author(s):  
Truong Minh Nhat ◽  
Truong Quoc Thanh ◽  
Tu Vinh Thong ◽  
Tran Trong Quyet ◽  
Luu Phuong Minh
Keyword(s):  
Tensile Strength ◽  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Thermal Contact ◽  
Welding Process ◽  
Welding Parameters ◽  
Thermal Imager ◽  
Sem Images ◽  
Cross Sectional ◽  
Friction Stir

This study presents conducted heat simulations and experimental jointing flat-plate of aluminum alloy 6061 and SUS 304. Temperature is simulated by the COMSOL software in three states: (1) Preheat the Friction Stir Welding (FSW) by TIG welding, (2) Thermal contact resistance between Aluminium and steel, and (3) The welding process using stiring friction is simulated. The simulations intended to predicting the temperature which is used for preheat and welding process to ensuring the required solid-state welding. The temperature is also determined and checked by a thermal imager comparing with simulation results. Besides, the results of tensile strength is carried out. The Box - Behnken method is used to identify the relationship between the welding parameters (rotation, speed and offset), temperature and tensile strength. The maximum tensile strength is 77% compared to the strength of aluminum alloy. The optimal set of parameters for the process is n = 676 rpm, v = 46 mm / min and x = 0.6 mm. The optimizing welding parameters to achieving good quality of welding process are described. SEM images to determine some properties of welding materials. This is also the basis for initial research to identify some defects in welding of two different materials (IMC thickness and interconnected pores) and the cause of these defects.

A study of tensile strength of MIG welding-brazing dissimilar lap joints of mild steel and aluminum alloy

2019 ◽  
Author(s):  
Abdulnasser Embark Beleed ◽  
A. I. M. Shaiful ◽  
Muhamad Fahmi Mohd Roslan ◽  
M. N. B. Omar ◽  
Mazlan Mohamed
Keyword(s):  
Tensile Strength ◽  
Aluminum Alloy ◽  
Mild Steel ◽  
Lap Joints ◽  
Mig Welding

Comparison of Residual Stress Between MIG Welding and Friction Stir Welding

2012 ◽  
Vol 155-156 ◽  
pp. 1218-1222
Author(s):  
Lei Wang ◽  
Mitsuyosi Tsunori
Keyword(s):  
Residual Stress ◽  
Friction Stir Welding ◽  
Stress Distribution ◽  
Yield Strength ◽  
Room Temperature ◽  
Welding Process ◽  
Residual Stress Distribution ◽  
Mig Welding ◽  
Friction Stir ◽  
Friction Stir Welding Process

Residual stress distribution plays a very important role in welded structures, the aim of present work is to find out the effect of different welding methods on the residual stress distribution by means of neutron diffraction measurements and FE models simulation. 4 mm thick DH-36 steel plates were butt welded by MIG welding process and 5 mm thick AA 2024 aluminium alloy plates were butt welded by friction stir welding process. Results show that residual stresses of MIG welding process are higher than those of friction stir welding process. The peak residual stress of MIG weld is close to the room temperature uniaxial yield strength of DH-36 while the peak residual stress of friction stir weld is just about 50% of the room temperature uniaxial yield strength of AA2024. The size effect of MIG welded and effect of welding speeds of friction stir welded on the residual stress distribution have also been studied in the paper.

Sign in / Sign up

Export Citation Format

Share Document