Nondestructive Evaluation Method of Average Grain Size in TWIP Steel by Laser Ultrasonic

2018 ◽  
Vol 913 ◽  
pp. 324-330
Author(s):  
Yan Jie Zhang ◽  
Xiao Chen Wang ◽  
Quan Yang ◽  
Ren Jie Xue ◽  
An Min Yin
Keyword(s):  
Grain Size ◽  
Manufacturing Industry ◽  
Evaluation Method ◽  
High Efficiency ◽  
Standard Sample ◽  
Twip Steel ◽  
Test Sample ◽  
Standard Samples ◽  
Laser Ultrasonic ◽  
Average Grain Size

TWIP steel has the characteristics of high elongation and high tensile strength at room temperature, and therefore it is widely used in the automobile manufacturing industry. Since the grain size has a very important influence on its mechanical properties and corrosion resistance it is significant to study the average grain size of TWIP steel. In this experiment, the specimens were heated to 700~1000°C and preserved for one hour, and the recrystallized structures with different average grain sizes were obtained. All the samples were tested by laser ultrasonic experimental platform and the standard sample was selected. Then the attenuation coefficients of remaining samples were compared with the standard samples by conventional methods. The results showed that the larger the difference between the average grain size of the test sample and the standard sample is, the greater the error of the test will be. The new evaluation model was established by the improved method, and the prediction error was reduced to 5.44~11.61%, which proved the effectiveness of the new method. In addition, laser ultrasonic testing has the advantages of high efficiency and no damage compared with traditional methods.

Influence of Grain Size on Mechanical Properties in a Fe-9Ni-12Mn-2.5Si-1.0C TWIP Steel

2011 ◽  
Vol 197-198 ◽  
pp. 655-661
Author(s):  
Ze Bin Yang ◽  
Ding Yi Zhu ◽  
Wei Fa Yi ◽  
Shu Mei Lin ◽  
Cheng Mei Du
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Strain Hardening ◽  
Twip Steel ◽  
Optical Microscope ◽  
Coarse Grained ◽  
Microstructure Observation ◽  
Transmission Electron ◽  
Average Grain Size

We investigate the influence of grain size on mechanical properties in a Fe-9Ni-12Mn-2.5Si-1.0C TWIP steel by unidirectional tensile. Meanwhile the microstructures of the TWIP steel were observed and analyzed by optical microscope (OM) and transmission electron microscope (TEM). The experimental results show that the TWIP steel’s yield strength and tensile strength decrease with the increasing of grain size, whereas the plasticity increases with it. When the average grain size reaches to 27μm, the tensile strength is 1080MPa, the elongation percentage is 77%, and the strength-plasticity product achieves the 83160MPa•%. Steel’s strain hardening rate can be changed from three-stage to four-stage with the increasing of grain sizes, the areas of strain hardening by twin deformation mechanism are expanded. Through the microstructure observation we found that, coarse-grained TWIP steel conducts to twinning formation, the high density twins can increase the alloy’s ductility by splitting the grain.

Microstructural and Mechanical Characterization of Autogenous GTAW Weld in High-Manganese Austenitic Steel Ti-Containing with Thermal Analysis

MRS Advances ◽  
2018 ◽  
Vol 3 (64) ◽  
pp. 3963-3969
Author(s):  
V. García-García ◽  
I. Mejía ◽  
F. Reyes-Calderón
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Weld Joint ◽  
Heat Input ◽  
Thermal Field ◽  
Twip Steel ◽  
Experimental Results ◽  
Butt Weld ◽  
Average Grain Size ◽  
Gtaw Process

ABSTRACTThe welding heat input has been pointed out as a main limiting factor for TWinnig Induced Plasticity (TWIP) steel weldability. Scarce research works have been focused on the study of application and effects of the Gas Tungsten Arc Welding (GTAW) process in the TWIP steel, especially in higher thickness plate. In this research work was conducted a detailed analysis of a butt weld joint performed in plates of TWIP steel microalloyed with titanium (TWIP-Ti) of 6.3 mm thickness. The autogenous GTAW process with low heat input was applied. The analysis considered grain size measurements, second phases identification, post-weld mechanical properties (microhardness) and the welding thermal field. A Finite Element Model (FEM), validated through experimental results, allowed correlating metallurgical results with the thermal field. Likewise, the phases prediction carried out by means of JMatPro 9.0 software during solidification process as well as the estimation of particle precipitation were in good agreement with the experimental results. These predictive diagrams were calculated taking into account the TWIP-Ti steel chemical composition, the grain size measured in critical weld regions and experimental cooling rates. The low heat input improved the microstructural conditions in the heat affected zone (HAZ) whose average grain size and precipitate particles, like (C, N)Ti, promoted good mechanical properties as compared to the base material (as-solution condition). Some particles like Al2O3 y MnS produced microporosities in the HAZ. Despite this, the weld joint did not present hot cracking in the FZ-HAZ interface.

scholarly journals Mechanical behavior of nanocrystalline Cu and Pd

1991 ◽  
Vol 6 (5) ◽  
pp. 1012-1027 ◽  
Author(s):  
G.W. Nieman ◽  
J.R. Weertman ◽  
R.W. Siegel
Keyword(s):  
Grain Size ◽  
Diffusional Creep ◽  
Coarse Grained ◽  
Dominant Factor ◽  
Ultrafine Grain ◽  
Uniaxial Tensile ◽  
Standard Samples ◽  
Dislocation Generation ◽  
Lattice Strains ◽  
Average Grain Size

This report gives results of a study of the bulk mechanical properties of samples of nanocrystalline Cu and Pd consolidated from powders prepared by inert gas condensation. Fourier analysis x-ray diffraction techniques, used to determine average grain size and mean lattice strains of the as-consolidated samples, show grain sizes in the range of 3–50 nm and lattice strains ranging from 0.02–3%. Sample densities range from 97–72% of the density of a coarse-grained standard. Microhardness of the nanocrystalline samples exceeds that of annealed, coarse-grained samples by a factor of 2–5, despite indications that sample porosity reduces hardness values below the ultimate value. Uniaxial tensile strength of the nanocrystalline samples is similarly elevated above the value of the coarse-grained standard samples. Restrictions on dislocation generation and mobility imposed by ultrafine grain size are believed to be the dominant factor in raising strength. Residual stress may also play a role. Room temperature diffusional creep, predicted to be appreciable in nanocrystalline samples, was not found. Instead, samples appear to show logarithmic creep that is much smaller than the predicted Coble creep.

Surface Modification and its Influence on the Microstructure and Creep Resistance of Nickel Based Superalloy René 77 / Modyfikacja Powierzchniowa Oraz Jej Wpływ Na Mikrostrukture I Wytrzymałosc Na Pełzanie Odlewów Z Nadstopu Niklu Ren´E 77

2013 ◽  
Vol 58 (1) ◽  
pp. 95-98 ◽  
Author(s):  
M. Zielinska ◽  
J. Sieniawski
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Surface Modification ◽  
Turbine Blades ◽  
Processing Parameters ◽  
Grain Structure ◽  
Creep Tests ◽  
Cobalt Aluminate ◽  
Nickel Based Superalloy ◽  
Average Grain Size

Superalloy René 77 is very wide used for turbine blades, turbine disks of aircraft engines which work up to 1050°C. These elements are generally produced by the investment casting method. Turbine blades produced by conventional precision casting methods have coarse and inhomogeneous grain structure. Such a material often does not fulfil basic requirements, which concern mechanical properties for the stuff used in aeronautical engineering. The incorporation of controlled grain size improved mechanical properties. This control of grain size in the casting operation was accomplished by the control of processing parameters such as casting temperature, mould preheating temperature, and the use of grain nucleates in the face of the mould. For nickel and cobalt based superalloys, it was found that cobalt aluminate (CoAl2O4) has the best nucleating effect. The objective of this work was to determine the influence of the inoculant’s content (cobalt aluminate) in the surface layer of the ceramic mould on the microstructure and mechanical properties at high temperature of nickel based superalloy René 77. For this purpose, the ceramic moulds were made with different concentration of cobalt aluminate in the primary slurry was from 0 to 10% mass. in zirconium flour. Stepped and cylindrical samples were casted for microstructure and mechanical examinations. The average grain size of the matrix ( phase), was determined on the stepped samples. The influence of surface modification on the grain size of up to section thickness was considered. The microstructure investigations with the use of light microscopy and scanning electron microscopy (SEM) enable to examine the influence of the surface modification on the morphology of ’ phase and carbides precipitations. Verification of the influence of CoAl2O4 on the mechanical properties of castings were investigated on the basis of results obtained form creep tests.

scholarly journals ODS EUROFER Steel Strengthened by Y-(Ce, Hf, La, Sc, and Zr) Complex Oxides

Metals ◽  
2019 ◽  
Vol 9 (11) ◽  
pp. 1148 ◽  
Author(s):  
Roman Husák ◽  
Hynek Hadraba ◽  
Zdeněk Chlup ◽  
Milan Heczko ◽  
Tomáš Kruml ◽  
...  
Keyword(s):  
Grain Size ◽  
Yield Strength ◽  
Complex Oxides ◽  
Oxide Dispersion Strengthened ◽  
Interparticle Spacing ◽  
Oxide Dispersion ◽  
Strengthening Effect ◽  
Dispersion Strengthening ◽  
Doping Element ◽  
Average Grain Size

Oxide dispersion-strengthened (ODS) materials contain homogeneous dispersions of temperature-stable nano-oxides serving as obstacles for dislocations and further pinning of grain boundaries. The strategy for dispersion strengthening based on complex oxides (Y-Hf, -Zr, -Ce, -La) was developed in order to refine oxide dispersion to enhance the dispersion strengthening effect. In this work, the strengthening of EUROFER steel by complex oxides based on Y and elements of the IIIB group (lanthanum, scandium) and IVB group (cerium, hafnium, zirconium) was explored. Interparticle spacing as a dispersoid characteristic appeared to be an important factor in controlling the dispersion strengthening contribution to the yield strength of ODS EUROFER steels. The dispersoid size and average grain size of ODS EUROFER steel were altered in the ranges of 5–13 nm and 0.6–1.7 µm, respectively. Using this strategy, the yield strength of the prepared alloys varied between 550 MPa and 950 MPa depending on the doping element.

scholarly journals An Intelligent Evaluation Method to Analyze the Competitiveness of Airlines

2020 ◽  
Vol 2020 ◽  
pp. 1-9
Author(s):  
Jun Zhao ◽  
Xumei Chen
Keyword(s):  
Neural Network ◽  
Prior Knowledge ◽  
Evaluation Method ◽  
Standard Sample ◽  
Reference Value ◽  
The Self ◽  
Index Data ◽  
Som Neural Network ◽  
Simulation Results ◽  
Self Organizing

An intelligent evaluation method is presented to analyze the competitiveness of airlines. From the perspective of safety, service, and normality, we establish the competitiveness indexes of traffic rights and the standard sample base. The self-organizing mapping (SOM) neural network is utilized to self-organize and self-learn the samples in the state of no supervision and prior knowledge. The training steps of high convergence speed and high clustering accuracy are determined based on the multistep setting. The typical airlines index data are utilized to verify the effect of the self-organizing mapping neural network on the airline competitiveness analysis. The simulation results show that the self-organizing mapping neural network can accurately and effectively classify and evaluate the competitiveness of airlines, and the results have important reference value for the allocation of traffic rights resources.

scholarly journals Development of Al–Mg–Si alloy performance by addition of grain refiner Al–5Ti–1B alloy

2021 ◽  
Vol 104 (2) ◽  
pp. 003685042110294
Author(s):  
Khaled Abd El-Aziz ◽  
Emad M Ahmed ◽  
Abdulaziz H Alghtani ◽  
Bassem F Felemban ◽  
Hafiz T Ali ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Corrosion Resistance ◽  
Testing Machine ◽  
Dendritic Structure ◽  
Grain Refiner ◽  
Corrosion Properties ◽  
Average Grain Size ◽  
Structural Applications ◽  
Alloy Addition

Aluminum alloys are the most essential part of all shaped castings manufactured, mainly in the automotive, food industry, and structural applications. There is little consensus as to the precise relationship between grain size after grain refinement and corrosion resistance; conflicting conclusions have been published showing that reduced grain size can decrease or increase corrosion resistance. The effect of Al–5Ti–1B grain refiner (GR alloy) with different percentages on the mechanical properties and corrosion behavior of Aluminum-magnesium-silicon alloy (Al–Mg–Si) was studied. The average grain size is determined according to the E112ASTM standard. The compressive test specimens were made as per ASTM: E8/E8M-16 standard to get their compressive properties. The bulk hardness using Vickers hardness testing machine at a load of 50 g. Electrochemical corrosion tests were carried out in 3.5 % NaCl solution using Autolab Potentiostat/Galvanostat (PGSTAT 30).The grain size of the Al–Mg–Si alloy was reduced from 82 to 46 µm by the addition of GR alloy. The morphology of α-Al dendrites changes from coarse dendritic structure to fine equiaxed grains due to the addition of GR alloy and segregation of Ti, which controls the growth of primary α-Al. In addition, the mechanical properties of the Al–Mg–Si alloy were improved by GR alloy addition. GR alloy addition to Al–Mg–Si alloy produced fine-grained structure and better hardness and compressive strength. The addition of GR alloy did not reveal any marked improvements in the corrosion properties of Al–Mg–Si alloy.

Sign in / Sign up

Export Citation Format

Share Document