Study on Friction and Wear Properties of Self-Lubricating Impregnated Diamond Bit Cutters

2011 ◽  
Vol 175 ◽  
pp. 136-139 ◽  
Author(s):  
Bing Suo Pan ◽  
Xiao Hong Fang ◽  
Ming Yuan Niu
Keyword(s):  
Friction Coefficient ◽  
Friction And Wear ◽  
Matrix Material ◽  
Wear Loss ◽  
Wear Properties ◽  
Wear Process ◽  
Impregnated Diamond Bit ◽  
Pin On Disc ◽  
Friction And Wear Properties ◽  
Diamond Bit

To reduce the friction coefficient between impregnated diamond bit and rock, experiments on addition of graphite to the matrix material of bit cutters were conducted. The cutters were made up of diamond contained working layers and binding layers. The friction and wear properties of cutters and binding layers were investigated using a pin-on-disc friction & wear tester with granite as tribopair. The results showed that with addition of graphite, the hardness and friction coefficient of binding layer decreased, but its wear resistance increased; compared to cutters without graphite, those cutters containing graphite had lower wear loss and friction coefficient and their sliding wear process was much steadier, but diamond protrusion was still normal.

Comparison of the Friction and Wear Properties of PTFE Coatings under Vacuum Conditions before and after Gamma Irradiation

2011 ◽  
Vol 311-313 ◽  
pp. 1177-1181 ◽  
Author(s):  
Xing Dong Yuan ◽  
Bin Xu ◽  
Xiao Jie Yang ◽  
Hai Long Ma
Keyword(s):  
Friction Coefficient ◽  
Gamma Irradiation ◽  
Friction And Wear ◽  
Sliding Velocity ◽  
Wear Properties ◽  
Sliding Speed ◽  
Wear Process ◽  
Before And After ◽  
Three Stages ◽  
Friction And Wear Properties

The friction and wear properties of Polytetrafluoroethylene (PTFE) coatings before and after gamma irradiation were studied under vacuum conditions. Experimental results indicated that the friction and wear properties of PTFE coatings were improved by gamma irradiation. Results showed that the wear process of PTFE coatings before and after gamma irradiation consists of three stages. The steps for the irradiated PTFE are slightly longer than that for the non-irradiated samples. The friction coefficient of irradiated PTFE coatings reduces slightly compared to that of the non-irradiated samples. The friction coefficients of the PTFE coatings before and after gamma irradiation first increase with the increase of sliding velocity and then decrease with the increase of sliding velocity, and The friction coefficient of PTFE coatings before and after gamma irradiation decreases with the increase of load. The wear of irradiated PTFE coatings is slightly lower than that of non-irradiated PTFE coatings. The wear of PTFE coatings before and after gamma irradiation first decreases with the increase of sliding speed and then increases as the sliding speed increases. The wear of PTFE coatings first decreases with the increase of load and then increases with the increase of load. Scanning electron microscope (SEM) was utilized to investigate the worn surfaces.

Friction and Wear Properties of Oriented Fe2B with Different Cr Additions under Water-Lubricated Condition

2020 ◽  
Vol 975 ◽  
pp. 3-8
Author(s):  
Ke Min Li ◽  
Zhi Fu Huang ◽  
Chao Feng Qin ◽  
Han Wen Ma ◽  
Wei Yao Zhang
Keyword(s):  
Fracture Toughness ◽  
Friction Coefficient ◽  
Cross Section ◽  
Laser Scanning ◽  
Friction And Wear ◽  
Longitudinal Section ◽  
Wear Loss ◽  
Wear Properties ◽  
Cr Addition ◽  
Friction And Wear Properties

In the present study, pure oriented Fe2B with Cr addition were prepared. The friction and wear properties of oriented Fe2B with different Cr additions were investigated by optical microscopy, scanning electron microscopy and 3D laser scanning microscope. Results indicate that fracture toughness of the cross section is higher than that of the longitudinal section invariably with the same Cr addition. Both cross and longitudinal sections, the fracture toughness value increases from 1Cr to 2Cr and decreases from 2Cr to 3Cr. Friction coefficient and wear loss of cross section are lower than those of the longitudinal section under the same Cr addition. For the identical grain orientation, the friction coefficient and wear loss rise from 1Cr to 2Cr and then drop from 2Cr to 3Cr. 2Cr-C sample has the lowest friction coefficient and wear loss. On the contrary, the friction coefficient and wear loss of 3Cr-L sample are the highest. Wear mechanisms of Fe2B alloy are brittle rupture and abrasive wear.

Effects of Load and Sliding Distance on the Wear Properties of Hybrid Friction Materials

2011 ◽  
Vol 686 ◽  
pp. 401-405 ◽  
Author(s):  
Ning Zhang ◽  
Li Xiang Chen ◽  
Yan Sheng Yin ◽  
Ye Han ◽  
Zong Feng Wang
Keyword(s):  
Friction Coefficient ◽  
Wear Rate ◽  
Friction And Wear ◽  
Phenolic Resin ◽  
Matrix Material ◽  
Wear Properties ◽  
Friction Materials ◽  
Potassium Titanate ◽  
Friction And Wear Properties ◽  
Sliding Distance

Hybrid friction materials were manufactured with glass fiber, potassium titanate whisker and aramid fiber as reinforcement and the phenolic resin modified by lumbar pericarps oil as matrix material. The effects of load and sliding distance on friction and wear properties were studied by single variable experiments. The worn surfaces of the samples were studied by Scanning Electron Microscope (SEM). The results showed that friction coefficient and wear rate can be significantly increased when the load was increased up to 250N. The friction coefficient varied between 0.25 and 0.3 while the wear rate reduced to 0.49×10-6 g/(N·m) in the sliding distance longer then 80m. Wear mechanism of samples were to be adhesive and abrasive wear.

Water Absorption, Friction and Wear Behaviors of Polypropylene Composites Filled with Hydroxyapatite

2017 ◽  
Vol 733 ◽  
pp. 60-64
Author(s):  
Munir Tasdemir ◽  
Ozkan Gulsoy
Keyword(s):  
Friction Coefficient ◽  
Wear Rate ◽  
Water Absorption ◽  
Polymer Composites ◽  
Friction And Wear ◽  
Wear Properties ◽  
Polypropylene Composites ◽  
Friction And Wear Properties

In the present work, the friction and wear properties of Polypropylene (PP) based composites filled with Hydroxyapatite (HA) particles were studied. Fillers contents in the PP were 10, 20, and 30 wt%. The effects of hydroxyapatite ratio on the water absorption, friction and wear properties of the polymer composites is presented. The result showed that the addition of HA to the composite changed the water absorption, friction coefficient and wear rate.

scholarly journals Improved Friction and Wear Properties of Al6061-Matrix Composites Reinforced by Cu-Ni Double-Layer-Coated Carbon Fibers

Metals ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1542
Author(s):  
Shuhan Dong ◽  
Huiyong Yuan ◽  
Xiaochao Cheng ◽  
Xue Zhao ◽  
Mingxu Yang ◽  
...  
Keyword(s):  
Carbon Fibers ◽  
Friction And Wear ◽  
Interfacial Bonding ◽  
Wear Testing ◽  
Double Layers ◽  
Wear Loss ◽  
Matrix Composites ◽  
Wear Properties ◽  
Al Composite ◽  
Friction And Wear Properties

The friction and wear properties of an Al6061 alloy reinforced with carbon fibers (CF) modified with Cu-Ni bimetallic layers were researched. Cu-Ni double layers were applied to the CF by electroless plating and Al6061-matrix composites were prepared by powder metallurgy technology. The metal-CF/Al interfaces and post-dry-wear-testing wear loss weights, friction coefficients, worn surfaces, and wear debris were characterized. After T6 heat treatment, the interfacial bonding mechanism of Cu-Ni-CF changed from mechanical bonding to diffusion bonding and showed improved interfacial bonding strength because the Cu transition layer reduced the fiber damage caused by Ni diffusion. The metal–CF interfacial bonding strongly influenced the composite’s tribological properties. Compared to the Ni-CF/Al and Cu-CF/Al composites, the Cu-Ni-CF/Al composite showed the highest hardness, the lowest friction coefficient and wear rate, and the best load-carrying capacity. The wear mechanisms of Cu-Ni-CF/Al composite are mainly slight abrasive wear and adhesive wear.

Research on Friction and Wear Properties of Plasma Spraying Ni-Base Alloy Coatings on Aluminum Alloy Surfaces

2012 ◽  
Vol 538-541 ◽  
pp. 207-213 ◽  
Author(s):  
Long He ◽  
Ye Fa Tan ◽  
Bin Cai ◽  
Hua Tan ◽  
Li Gao ◽  
...  
Keyword(s):  
Aluminum Alloy ◽  
Abrasive Wear ◽  
Plasma Spraying ◽  
Intermediate Layer ◽  
Friction And Wear ◽  
Base Alloy ◽  
Wear Loss ◽  
Wear Properties ◽  
Fatigue Wear ◽  
Friction And Wear Properties

In order to improve the wear resistance and extend service life of aluminum alloy parts, the Ni-base alloy anti-wear coatings were prepared on the surfaces of 7A05 aluminum alloy by plasma spraying technology. The microstructure and interface of the coatings were analyzed, and the friction and wear properties of Ni-base alloy coatings and aluminum alloy substrates were investigated under dry friction condition at room temperature. The research results show that the main phases of Ni-base alloy coating are γ-Ni, CrB and Cr23C6. The thicknesses of diffusion layers existing between intermediate layer and coating, intermediate layer and substrate are respectively 15μm and 20μm. The bonding types of the coating and the substrate are mechanical combination accompanied with partially metallurgical combination. When wore against GCr15 steel balls, the average friction coefficient of the Ni-base alloy coatings is 11.6% lower than that of the aluminum alloy substrates, and the average wear loss of the former is 9.3mg, which is only 1/3 of that of the latter. With the increase of loads, the wear mechanisms of the Ni-base alloy coatings change from slightly micro-cutting wear and fatigue wear to abrasive wear and micro-fracture wear, while those of the aluminum alloy substrates are mainly adhesive wear and abrasive wear as well as slight oxidation wear.

Friction and Wear Properties of Ti-6Al-4V Surface Modified by Nitriding-Mo Plating-Sulfurizing Composite Treatment

2010 ◽  
Vol 139-141 ◽  
pp. 439-442
Author(s):  
Li Jie Wang ◽  
Jun Sheng Yang ◽  
Ya Zhe Xing
Keyword(s):  
Friction And Wear ◽  
Composite Layer ◽  
Wear Test ◽  
Xrd Analysis ◽  
Wear Loss ◽  
Treatment Technique ◽  
Ion Nitriding ◽  
Wear Properties ◽  
Cross Sectional ◽  
Friction And Wear Properties

A composite layer was prepared on the Ti-6Al-4V alloy surface by ion nitriding, magnetron sputtering Mo and ion sulfurizing composite treatment technique. The phase structure, morphology, and cross-sectional element distribution of composite layer were analyzed. Friction and wear properties of composite layer were tested by MM-200 laboratory tester. XRD analysis showed that the composite layer was mainly comprised of Ti, Mo, MoS2, TiN, and transition layer. This composite layer is perfect wear-resistant surface due to existence of self-lubricating MoS2 on hard Mo and TiN layers with good anti-friction ability. Thereby, the results of friction and wear test showed that anti-wear performance of Ti-6Al-4V alloy after composite treatment was remarkably improved under dry and sliding conditions. Both the friction coefficient and the wear loss of the nitriding-Mo plating-sulfurizing layers were lower than that of the nitriding layer due to the formation of the MoS2 layer on Mo and TiN layers.

Friction and Wear Characteristics of Magneto-Rheological Elastomers Based on Silicone/Polyurethane Hybrid

2015 ◽  
Vol 137 (3) ◽  
Author(s):  
Chenglong Lian ◽  
Kwang-Hee Lee ◽  
Chul-Hee Lee
Keyword(s):  
Friction And Wear ◽  
Matrix Material ◽  
Operating Conditions ◽  
Wear Depth ◽  
Test Results ◽  
Wear Properties ◽  
Wear Performance ◽  
Friction And Wear Properties ◽  
Magneto Rheological ◽  
Mr Effect

The friction and wear properties of four different types of magneto-rheological (MR) elastomer were investigated. The MR elastomers have different matrix materials and structures. Most MR elastomers have a silicone matrix, since it has a more significant MR effect under a magnetic field compared to other materials. The mechanical properties of silicone, however, are poor compared to other materials, so it is difficult to use them in engineering applications. Therefore, a new polyurethane matrix material was used to enhance the friction and wear properties of MR elastomer. Additionally, two different matrix materials (silicone and polyurethane) were synthesized, and MR elastomers were structurally combined to improve the friction and wear performance. The friction characteristics of each MR elastomer were evaluated under reciprocating operating conditions. Wear depth was also measured to estimate the wear resistance. The test results show that the friction and wear performance of the modified MR elastomers are enhanced compared with the silicone-based MR elastomer.

A Comparative Study on the Friction and Wear Properties of Three Different Copper Alloys

2018 ◽  
Vol 913 ◽  
pp. 205-211
Author(s):  
Dong Mei Liu ◽  
Qiang Song Wang ◽  
Wei Yuan ◽  
Xu Jun Mi
Keyword(s):  
Friction Coefficient ◽  
Comparative Study ◽  
Dry Friction ◽  
Friction And Wear ◽  
Copper Alloys ◽  
Friction Condition ◽  
Al Alloy ◽  
Wear Properties ◽  
Friction Coefficients ◽  
Friction And Wear Properties

A comparative study on the friction and wear properties of three kinds of copper alloys, including Cu-Ni based, Cu-Al and Cu-Be alloys was carried out in this study. The friction pair was stainless steel, and both dry and MoS2 lubrication friction experiments were investigated. During the experiments, different loads were chosen for different alloys. It was found that under dry friction condition, the friction coefficients of both Cu-Ni based and Cu-Al alloys did not change as the loads changes, whereas the friction coefficient of Cu-Be alloy increased as the loads increases. Under lubrication friction condition, the friction coefficients of all three alloys did not change as the load changes. The results show that the dry friction coefficient of Cu-Ni based alloy was the largest (0.74), the Cu-Al alloy next (0.60), and the Cu-Be alloy had the smallest dry friction coefficient (0.54). The lubrication friction coefficient of Cu-Ni based and Cu-Be was equal and relatively smaller (0.12), whereas the Cu-Al alloy had a relative larger lubrication friction coefficient (0.27). The microstructure observations were consistent with the friction and wear performance, and the SEM results show that different wear mechanisms were dominated for different alloys.

Effect of Ultrasonic Vibration on the Friction and Wear Properties of GCr15/45# Steel Frictional Pairs Lubricated by n-Al2O3 Additives

2012 ◽  
Vol 538-541 ◽  
pp. 1920-1923
Author(s):  
Yu Lin Qiao ◽  
Shan Lin Yang ◽  
Yan Zang ◽  
Xin Yu Dong ◽  
Qing Sheng Cui
Keyword(s):  
Friction Coefficient ◽  
Ultrasonic Vibration ◽  
Photoelectron Spectroscopy ◽  
Friction And Wear ◽  
Ball Bearing ◽  
Wear Scar ◽  
Friction Reduction ◽  
Wear Volume ◽  
Wear Properties ◽  
Friction And Wear Properties

The friction and wear properties of GCr15/45# steel frictional pairs lubricated by n- Al2O3 additives under ultrasonic vibration or not were studied. The scanning electron microscope(SEM), X-ray photoelectron spectroscopy(XPS) and energy dispersive spectrometer (EDS) were carried out to analyse the wear scar surface. The effect mechanism of ultrasonic vibration on friction pairs was discussed. The results indicated that ultrasonic vibration could decrease the friction and wear of GCr15/45# friction pairs, when the content of n-Al2O3 was 0.5wt%, the effect of ultrasonic vibration on friction pairs was most obvious. The friction coefficient, wear volume and wear scar depth under ultrasonic vibration decreased 10%, 34% and 13%, respectively. The friction reduction and anti-wear mechanism of n-Al2O3 was single “micro ball bearing” without ultrasonic vibration, and it changed to “micro ball bearing” and adsorption penetration film with ultrasonic vibration, so the friction coefficient and wear volume was reduced.

Sign in / Sign up

Export Citation Format

Share Document