INFLUENCE OF DIFFERENT DEPTHS OF PLOWING ON THE PHYSICAL PROPERTIES OF A CLAY SOIL AT GUYENNE, QUEBEC

1963 ◽  
Vol 43 (1) ◽  
pp. 178-185
Author(s):  
J. R. Lessard ◽  
H. A. Hamilton ◽  
M. Levesque ◽  
S. J. Bourget

An experiment was initiated in 1955 to study the effect of plowing to depths of 6, 12 and 24 inches on the physical properties of a Guyenne clay soil. A 4-year crop rotation was established. Soil core samples were taken in 1957, 1959 and 1960 and determinations of bulk density and porosities were made. The soil particle-size distribution was determined for all tillage treatments in 1960.Plowing to a depth of 24 inches resulted in higher bulk density and lower non-capifiary porosity values in the surface 6-inch soil layer of soil than the 6- and 12-inch plowing. The 18- to 24-inch soil layer was less packed than the corresponding undisturbed layers at the same depth, as a result of deep tillage. The clay content of the 0- to 6-inch layer of soil was also increased by 24-inch plowing. Year-to-year data showed the importance of seasonal climatic conditions on the soil physical properties.

2008 ◽  
Vol 2 (No. 1) ◽  
pp. 15-24 ◽  
Author(s):  
M. Kroulík ◽  
J. Hůla ◽  
R. Šindelář ◽  
F. Illek

Soil infiltration capacity is one of the key factors in the soil protection against unfavourable effects of water erosion. The purpose of its measuring was to compare and evaluate the changes of the soil physical properties and of water infiltration into soil caused by different intensity of soil cultivation at two individual sites. The ploughing (PL), shallow tillage (ST), and direct drilling (NT) effects on the soil physical properties, water infiltration into soil, and soil surface coverage with the crop residua under the soil condition loamy Haplic Luvisol, with long-term growing of maize (Zea mays L.) - Agroservis, 1<sup>st</sup> Agricultural, a.s., Vi&scaron;ňov&eacute; - and clay soil of Calcic Chernozem (Cooperative farm Klap&yacute;), were compared. Soil bulk density values in the variant with ploughing showed in the depth up to 0.20 m considerably lower values as compared with the variants shallow tillage and direct drilling. Nevertheless, in the subsoil layer the bulk density of soil in the variant with ploughing increased in comparison with other variants. The results were also confirmed by the cone index values. At the plots in Vi&scaron;ňov&eacute; the infiltration was evaluated utilising the double ring infiltrometer, and by means of the coloured water infiltration. The results revealed significant differences in the water infiltration rate at various stages of the soil loosening. The highest average values were recorded for ploughing (1.00 dm<sup>3</sup>/min). The lowest values were found for the shallow soil tillage (0.18 dm<sup>3</sup>/min). The variant with direct drilling showed values of 0.53 dm<sup>3</sup>/min. The coloured water infiltration evaluation showed a different character of water flow in soil. The variant with ploughing showed water saturation in the top layer, the variants with reduced tillage were characterised by vertical macropores and crack effects with the water drain into deeper layers. Ploughing proved its advantage for the short-term rainfall retention. Similar results were also brought in the evaluation on the plot with clay soil (Klap&yacute;). The loosening effect was evident during coloured water infiltration in the period of snow thawing. The loosed soil layer showed a significantly higher soil water holding capacity as compared with variants with reduced soil tillage. The result showed major differences in the water infiltration rate into soil and different characters of water infiltration into soil at different soil tillage.


2011 ◽  
Vol 6 (No. 2) ◽  
pp. 73-82 ◽  
Author(s):  
S.E. Obalum ◽  
J.C. Nwite ◽  
J. Oppong ◽  
C.A. Igwe ◽  
T. Wakatsuki

One peculiar feature of the inland valleys abundant in West Africa is their site-specific hydrology, underlain mainly by the prevailing landforms and topography. Development and management of these land resources under the increasingly popular sawah (a system of bunded, puddled and levelled rice field with facilities for irrigation and drainage) technology is a promising opportunity for enhancing rice (Oryza sativa L.) production in the region. Information on the variations in selected soil physical properties as influenced by the prevailing landforms may serve as a useful guide in site selection. This is of practical importance since majority of the inland valleys are potentially unsuitable for sawah development and most farmers in the region are of low technical level. Three landforms (river levee, elevated area and depressed area) were identified within a sawah field located in an inland valley at Ahafo Ano South District of Ghana. Each of these landforms was topsoil-sampled along on identified gradient (top, mid and bottom slope positions). Parameters determined included particle size distribution, bulk density, total porosity and field moisture content. The soil is predominantly clayey. There were no variations in the particle size distribution among the slope positions in the river levee. Overall, the river levee had lower silt content than the elevated and the depressed landforms. The bulk density, total porosity, and gravimetric moisture content indicated relative improvements only in the depressed area in the order, bottom &gt; mid &gt; top slope. Irrespective of slope position, the three landforms differed in these parameters in the order, depressed &gt; river levee &gt; elevated. The sand fraction impacted negatively on the silt fraction and bulk density of the soil, both of which controlled the soil moisture status. Despite the fairly low silt content of the soil, the silt fraction strongly influenced the gravimetric moisture content (R<sup>2</sup> = 0.80). So too did the soil bulk density on the gravimetric moisture content (R<sup>2</sup> = 0.90). It is concluded that: (1) since the landforms more prominently influenced the measured parameters than the slope positions, the former should take pre-eminence over the latter in soil suitability judgment; (2) with respect to moisture retention, variations in silt fraction and bulk density of this and other clayey inland-valley soils should be used as guide in site selection for sawah development.


1988 ◽  
Vol 24 (3) ◽  
pp. 375-384 ◽  
Author(s):  
N. R. Hulugalle ◽  
M. S. Rodriguez

SUMMARYThe soil physical properties of tied ridges were measured in a trial, established in 1983, comparing three treatments: handhoe cultivation and planting on the flat; planting directly without any cultivation on tied ridges constructed the previous year; and handhoe cultivation and remoulding of tied ridges constructed the previous year. Two maize varieties and two management levels were used. The soil properties monitored were particle size distribution, penetro-meter resistance in the surface 20 mm, bulk density, water infiltration, soil water retention and soil temperature.Soil physical properties were affected mainly by the type of seedbed. Clay content in the surface 0.05 m was greater with tied ridging, with that in the furrows being higher than that in the ridge slopes. Daily maximum soil temperature was greatest in the flat planted plots and in the ridge slopes of the tied ridged plots. Penetrometer resistance at a soil water content of 0.05 kg kg−1 was greater in the tied ridged plots. Cumulative infiltration after 2 h was greatest with flat planting. The bulk density of ridge slopes in tied ridged plots was less than that in the furrows and in the flat planted plots. Soil water retention was greatest in the furrows of the tied ridged plots. Clay content was the major factor determining all the soil physical properties measured.


Soil Research ◽  
1995 ◽  
Vol 33 (5) ◽  
pp. 851 ◽  
Author(s):  
MS Lorimer ◽  
LA Douglas

The effects of five management practices (native forest, native pasture, Phalaris pasture, crop-pasture rotation, continuous cropping), that had been in place for 18 years, on some soil physical properties of a red-brown earth near Bendigo, Victoria, were studied. Particle size distribution, bulk density and hydraulic conductivity of soil in the A and B horizons at different, management sites were measured. Where cultivation had occurred, soil in the A horizon contained less silt and clay, and more fine sand and coarse sand. The bulk density of the A horizon of soil that had produced at least six wheat crops since 1969 was greater than that of soil used for pasture or forest, while the hydraulic conductivity of soil cropped every year since 1969 was much less than that of soil under native forest. Particle size distributions for soil from the B horizons at the five management sites were found to be similar. Where pastures and crops had been established, the hydraulic conductivity of the upper B horizon was lower, and the bulk density was higher, than that of soil in the native forest (Eucalyptus spp).


Soil Research ◽  
2017 ◽  
Vol 55 (8) ◽  
pp. 778
Author(s):  
G. S. A. Castro ◽  
C. A. C. Crusciol ◽  
C. A. Rosolem ◽  
J. C. Calonego ◽  
K. R. Brye

This work aimed to evaluate the effects of crop rotations and soil acidity amelioration on soil physical properties of an Oxisol (Rhodic Ferralsol or Red Ferrosol in the Australian Soil Classification) from October 2006 to September 2011 in Botucatu, SP, Brazil. Treatments consisted of four soybean (Glycine max)–maize (Zea mays)–rice (Oryza sativa) rotations that differed in their off-season crop, either a signal grass (Urochloa ruziziensis) forage crop, a second crop, a cover crop, or fallow. Two acid-neutralising materials, dolomitic lime (effective calcium carbonate equivalent (ECCE) = 90%) and calcium-magnesium silicate (ECCE = 80%), were surface applied to raise the soil’s base saturation to 70%. Selected soil physical characteristics were evaluated at three depths (0–0.1, 0.1–0.2, and 0.2–0.4 m). In the top 0.1 m, soil bulk density was lowest (P < 0.05) and macroporosity and aggregate stability index were greatest (P < 0.05) in the forage crop compared with all other production systems. Also, bulk density was lower (P < 0.05) and macroporosity was greater (P < 0.05) in the acid-neutralising-amended than the unamended control soil. In the 0.1–0.2-m interval, mean weight diameter and mean geometric diameter were greater (P < 0.05) in the forage crop compared with all other production systems. All soil properties evaluated in this study in the 0.2–0.4-m interval were unaffected by production system or soil amendment after five complete cropping cycles. Results of this study demonstrated that certain soil physical properties can be improved in a no-tillage soybean–maize–rice rotation using a forage crop in the off-season and with the addition of acid-neutralising soil amendments. Any soil and crop management practices that improve soil physical properties will likely contribute to sustaining long-term soil and crop productivity in areas with highly weathered, organic matter-depleted, acidic Oxisols.


2012 ◽  
Vol 29 (7) ◽  
pp. 933-943 ◽  
Author(s):  
Weinan Pan ◽  
R. P. Boyles ◽  
J. G. White ◽  
J. L. Heitman

Abstract Soil moisture has important implications for meteorology, climatology, hydrology, and agriculture. This has led to growing interest in development of in situ soil moisture monitoring networks. Measurement interpretation is severely limited without soil property data. In North Carolina, soil moisture has been monitored since 1999 as a routine parameter in the statewide Environment and Climate Observing Network (ECONet), but with little soils information available for ECONet sites. The objective of this paper is to provide soils data for ECONet development. The authors studied soil physical properties at 27 ECONet sites and generated a database with 13 soil physical parameters, including sand, silt, and clay contents; bulk density; total porosity; saturated hydraulic conductivity; air-dried water content; and water retention at six pressures. Soil properties were highly variable among individual ECONet sites [coefficients of variation (CVs) ranging from 12% to 80%]. This wide range of properties suggests very different behavior among sites with respect to soil moisture. A principal component analysis indicated parameter groupings associated primarily with soil texture, bulk density, and air-dried water content accounted for 80% of the total variance in the dataset. These results suggested that a few specific soil properties could be measured to provide an understanding of differences in sites with respect to major soil properties. The authors also illustrate how the measured soil properties have been used to develop new soil moisture products and data screening for the North Carolina ECONet. The methods, analysis, and results presented here have applications to North Carolina and for other regions with heterogeneous soils where soil moisture monitoring is valuable.


2016 ◽  
Vol 30 (2) ◽  
pp. 237-243 ◽  
Author(s):  
Karolina Szulc ◽  
Andrzej Lenart

Abstract The paper presents an influence of raw material composition and technological process applied on selected physical properties of food powders. Powdered multi-component nutrients were subjected to the process of mixing, agglomeration, coating, and drying. Wetting liquids ie water and a 15% water lactose solution, were used in agglomeration and coating. The analyzed food powders were characterized by differentiated physical properties, including especially: particle size, bulk density, wettability, and dispersibility. The raw material composition of the studied nutrients exerted a statistically significant influence on their physical properties. Agglomeration as well as coating of food powders caused a significant increase in particle size, decreased bulk density, increased apparent density and porosity, and deterioration in flowability in comparison with non-agglomerated nutrients.


2021 ◽  
pp. 44-57
Author(s):  
Kh. A. Shaban ◽  
M. A. Esmaeil ◽  
A. K. Abdel Fattah ◽  
Kh. A. Faroh

A field experiment was carried out at Khaled Ibn El-waleed village, Sahl El-Hussinia, El-Sharkia Governorate, Egypt, during two summer seasons 2019 and 2020 to study the effect of NPK nanofertilizers, biofertilizers and humic acid combined with or without mineral fertilizers different at rates on some soil physical properties and soybean productivity and quality under saline soil conditions. The treatments consisted of: NPK-chitosan, NPK-Ca, humic acid, biofertilzer and control (mineral NPK only). In both seasons, the experiment was carried out in a split plot design with three replicates. The results indicated a significant increase in the soybean yield parameters as compared to control. There was also a significant increase in dry and water stable aggregates in all treatments as compared to control. The treatment NPK-Chitosan was the best in improving dry and stable aggregates. Also, hydraulic conductivity and total porosity values were significantly increased in all treatments due to increase in soil aggregation and porosity that led to increase in values of hydraulic conductivity. Values of bulk density were decreased, the lowest values of bulk density were found in NPK-chitosan treatment as a result of the high concentration of organic matter resulted from NPK-chitosan is much lighter in weight than the mineral fraction in soils. Accordingly, the increase in the organic fraction decreases the total weight and bulk density of the soil. Concerning soil moisture constants, all treatments significantly increased field capacity and available water compared to control. This increase was due to improvement of the soil aggregates and pores spaces which allowed the free movement of water within the soil thereby, increasing the moisture content at field capacity.


2021 ◽  
Author(s):  
Martin Zanutel ◽  
Sarah Garré ◽  
Charles Bielders

&lt;p&gt;In the context of global soil degradation, biochar is being promoted as a potential solution to improve soil quality, besides its carbon sequestration potential. Burying biochar in soils is known to effect soil physical quality in the short-term (&lt;5 years), and the intensity of these effects depends on soil texture. However, the long-term effects of biochar remain largely unknown yet and are important to quantify given biochar&amp;#8217;s persistency in soils. The objective of this study was therefore to assess the long-term effect of biochar on soil physical properties as a function of soil texture and biochar concentration.&amp;#160; For this purpose, soil physical properties (particle density, bulk density, porosity, water retention and hydraulic conductivity curves) were measured in the topsoil of three fields with former kiln sites containing charcoal more than 150 years old in Wallonia (southern Belgium).&amp;#160; The fields had a silt loam, loam and sandy loam texture.&amp;#160; Samples were collected along 3 transects in each field, from the center of the kiln sites outwards.&amp;#160;&lt;/p&gt;&lt;p&gt;Particle density and bulk density slightly decreased as a function of charcoal content. Because particle density and bulk density were affected to a similar extent by charcoal content, total porosity was not affected by the presence of century-old charcoal. Regarding the soil water retention curve, charcoal affected mostly water content in the mesopore range. This effect was strongest for the sandy loam. On the other hand, the presence of century-old charcoal increased significantly the hydraulic conductivity at pF between 1.5 and 2 for the silt loam, while no effect of charcoal was observed for the loamy soil.&amp;#160; The study highlights a limited effect of century-old charcoal on the pore size distribution (at constant porosity) and on the resulting soil physical properties for the range of soils and charcoal concentrations investigated here.&amp;#160; Further research may be needed to confirm the observed trends over a wider range of soil types.&amp;#160;&lt;/p&gt;


Agronomy ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1697
Author(s):  
Matthieu Forster ◽  
Carolina Ugarte ◽  
Mathieu Lamandé ◽  
Michel-Pierre Faucon

Compaction due to traffic is a major threat to soil functions and ecosystem services as it decreases both soil pore volume and continuity. The effects of roots on soil structure have previously been investigated as a solution to alleviate compaction. Roots have been identified as a major actor in soil reinforcement and aggregation through the enhancement of soil microbial activity. However, we still know little about the root’s potential to protect soil from compaction during traffic. The objective of this study was to investigate the relationships between root traits and soil physical properties directly after traffic. Twelve crop species with contrasting root traits were grown as monocultures and trafficked with a tractor pulling a trailer. Root traits, soil bulk density, water content and specific air permeability were measured after traffic. The results showed a positive correlation between the specific air permeability and root length density and a negative correlation was found between bulk density and the root carbon/nitrogen ratio. This study provides first insight into how root traits could help reduce the consequences of soil compaction on soil functions. Further studies are needed to identify the most efficient plant species for mitigation of soil compaction during traffic in the field.


Sign in / Sign up

Export Citation Format

Share Document