scholarly journals Effect of the Dynamic Resistance on the Maximum Output Power in Dynamic Modelling of Photovoltaic Solar Cells

2022 ◽  
Vol 10 (01) ◽  
pp. 48-57
Author(s):  
Siaka Touré
Keyword(s):  
Solar Cells ◽  
Output Power ◽  
Maximum Output Power ◽  
Dynamic Modelling ◽  
Dynamic Resistance ◽  
Maximum Output ◽  
Photovoltaic Solar Cells

Improvement in Power of Shingled Solar Cells for Photo-Voltaic Module

2020 ◽  
Vol 20 (11) ◽  
pp. 7096-7099
Author(s):  
Hongsub Jee ◽  
Jinho Song ◽  
Daehan Moon ◽  
Jaehyeong Lee ◽  
Chaehwan Jeong
Keyword(s):  
Solar Cells ◽  
Output Power ◽  
Current Density ◽  
Power Loss ◽  
Maximum Output Power ◽  
Photovoltaic Module ◽  
Maximum Output ◽  
Conductive Adhesives ◽  
Electrically Conductive ◽  
Electrically Conductive Adhesives

This paper presents a study on the effects of heat treatment conditions on electrically conductive adhesives. Among the advantages of the shingled solar cells include larger active area and smaller current density since one of the main factors of the power loss is due to a decrease in current density. Therefore, when there is a small current, there is a benefit in regards to the power loss. The advantage of this new technique of developing photovoltaic modules is the increase of module power using the same installed area. Electrically conductive adhesives play an important role in the manufacture of shingled solar cells and understanding the effects of its curing condition is necessary to maximize its output power. Through changing the curing time and temperature, the optimized curing conditions for electrically conductive adhesives and fabricated shingled strings for development of a module could be established. Finally, we demonstrated a 500 mm × 500 mm photovoltaic module with a conventional and the other using the shingled method for purposes of comparison and a shingled module showed about 29% increase in maximum output power compared to a conventional module with the same installed area.

scholarly journals The Effect of Noise-Induced Quantum Coherence in the Intermediate Band Solar Cells

2021 ◽  
Author(s):  
Mohsen Daryani ◽  
Ali Rostami ◽  
Gaffar Darvish ◽  
Mohammad Kazem Morravej Farshi
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Output Power ◽  
Quantum Coherence ◽  
Maximum Output Power ◽  
Maximum Output ◽  
Incoherent Light ◽  
Intermediate Band ◽  
Intermediate Band Solar Cells ◽  
Coherence Effect

Abstract It has been shown that quantum coherence induced by incoherent light can increase the efficiency of solar cells. Here we evaluate the effect of such coherence in the intermediate band solar cells. We first examine a six-level quantum IBSC model and demonstrate by simulation that the maximum of output power in a solar cell with quantum structure increases more than 16 percent in the case of coherence existence. We then propose an IBSC model which can absorb continuous spectra of sunlight and show that the quantum coherence can increase the output power of the cell. For instance, calculations indicate that the coherence makes an increase of about 31% in the maximum output power of a cell that the width of the conduction and intermediate bands are 100 and 10 meV, respectively. Also, our calculations show that the quantum coherence effect is still observed in increasing the solar cell power by expanding the width of the conduction band, although the output power is reduced due to increase in the thermalization loss. However, expanding the width of the intermediate band reduces the coherence effect.

Research of Matching Power for Photovoltaic Charging Control System

2014 ◽  
Vol 620 ◽  
pp. 220-224
Author(s):  
Xin Sheng He ◽  
Zuo Cai Dai ◽  
Chun Fu Gao ◽  
Shao Tai Deng
Keyword(s):  
Solar Cells ◽  
Output Power ◽  
Solar Power ◽  
Maximum Output Power ◽  
Optimum Operating ◽  
Variable Step Size ◽  
Maximum Output ◽  
Resistive Load ◽  
Step Size ◽  
Load Matching

For the maximum output power varies with changes in load characteristics match the characteristics of solar cells in photovoltaic power generation system, the system runs through dynamic MPPT maximum power of self-optimizing process to achieve power from the PV charge control match. First, the output characteristic simulation analysis of the solar load resistive, capacitive load showed that solar power batteries for load matching efficiency is higher than in a purely resistive load. Then, using the improved algorithm for variable step size perturbation and observation of the received output power of solar power and load matching control, experiments showed that the optimum operating point of the circuit can control the real-time monitoring of solar cells and load. The output power from the battery load matching circuit to match the time working in the best working condition, if the energy is surplus or shortage, the system can control dynamic self-optimizing adjustment to charge, which leads to batteries absorbed power increasing and the efficiency of solar energy collection improving.

scholarly journals Tandem Solar Cells Based on Cu2O and c-Si Subcells in Parallel Configuration: Numerical Simulation

2017 ◽  
Vol 2017 ◽  
pp. 1-6 ◽  
Author(s):  
Mihai Răzvan Mitroi ◽  
Valerică Ninulescu ◽  
Laurenţiu Fara
Keyword(s):  
Numerical Simulation ◽  
Solar Cells ◽  
Solar Cell ◽  
Output Power ◽  
High Efficiency ◽  
Low Cost ◽  
Maximum Output Power ◽  
Model Parameters ◽  
Maximum Output ◽  
Parallel Configuration

A tandem solar cell consisting of a bottom c-Si high-efficiency subcell and a top low-cost Cu2O subcell in parallel configuration is evaluated for the first time by a use of an electrical model. A numerical simulation based on the single-diode model of the solar cell is performed. The numerical method determines both the model parameters and the parameters of the subcells and tandem from the maximization of output power. The simulations indicate a theoretical limit value of the tandem power conversion efficiency of 31.23% at 298 K. The influence of temperature on the maximum output power is analyzed. This tandem configuration allows a great potential for the development of a new generation of low-cost high-efficiency solar cells.

scholarly journals One-Step Preparation of Biochar Electrodes and Their Applications in Sediment Microbial Electrochemical Systems

Catalysts ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 508
Author(s):  
Kui You ◽  
Zihan Zhou ◽  
Chao Gao ◽  
Qiao Yang
Keyword(s):  
Output Power ◽  
Electrode Materials ◽  
Maximum Output Power ◽  
Composite Cathode ◽  
Maximum Output ◽  
Electrochemical Systems ◽  
Composite Cathodes ◽  
One Step ◽  
Microbial Electrochemical Systems ◽  
Hot Melt

Biochar is a kind of carbon-rich material formed by pyrolysis of biomass at high temperature in the absence or limitation of oxygen. It has abundant pore structure and a large surface area, which could be considered the beneficial characteristics for electrodes of microbial electrochemical systems. In this study, reed was used as the raw material of biochar and six biochar-based electrode materials were obtained by three methods, including one-step biochar cathodes (BC 800 and BC 700), biochar/polyethylene composite cathodes (BP 5:5 and BP 6:4), and biochar/polyaniline/hot-melt adhesive composite cathode (BPP 5:1:4 and BPP 4:1:5). The basic physical properties and electrochemical properties of the self-made biochar electrode materials were characterized. Selected biochar-based electrode materials were used as the cathode of sediment microbial electrochemical reactors. The reactor with pure biochar electrode (BC 800) achieves a maximum output power density of 9.15 ± 0.02 mW/m2, which increases the output power by nearly 80% compared with carbon felt. When using a biochar/polyaniline/hot-melt adhesive (BPP 5:1:4) composite cathode, the output power was increased by 2.33 times. Under the premise of ensuring the molding of the material, the higher the content of biochar, the better the electrochemical performance of the electrodes. The treatment of reed powder before pyrolysis is an important factor for the molding of biochar. The one-step molding biochar cathode had satisfactory performance in sediment microbial electrochemical systems. By exploring the biochar-based electrode, waste biomass could be reused, which is beneficial for the environment.

scholarly journals Study of the Properties of a Hybrid Piezoelectric and Electromagnetic Energy Harvester for a Civil Engineering Low-Frequency Sloshing Environment

Energies ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 391
Author(s):  
Nan Wu ◽  
Yuncheng He ◽  
Jiyang Fu ◽  
Peng Liao
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Civil Engineering ◽  
Maximum Output Power ◽  
Low Frequency ◽  
Electromagnetic Energy ◽  
Maximum Output ◽  
Piezoelectric Film ◽  
Hybrid Energy ◽  
Level Height

In this paper a novel hybrid piezoelectric and electromagnetic energy harvester for civil engineering low-frequency sloshing environment is reported. The architecture, fabrication and characterization of the harvester are discussed. The hybrid energy harvester is composed of a permanent magnet, copper coil, and PVDF(polyvinylidene difluoride) piezoelectric film, and the upper U-tube device containing a cylindrical fluid barrier is connected to the foundation support plate by a hinge and spring. The two primary means of energy collection were through the vortex street, which alternately impacted the PVDF piezoelectric film through fluid shedding, and the electromotive force (EMF) induced by changes in the magnetic field position in the conducting coil. Experimentally, the maximum output power of the piezoelectric transformer of the hybrid energy harvester was 2.47 μW (circuit load 270 kΩ; liquid level height 80 mm); and the maximum output power of the electromagnetic generator was 2.72 μW (circuit load 470 kΩ; liquid level height 60 mm). The low-frequency sloshing energy collected by this energy harvester can drive microsensors for civil engineering monitoring.

LD-pumped high-power continuous-wave Pr3+:YLF deep red lasers at 718.5 and 720.8 nm

Laser Physics ◽  
2021 ◽  
Vol 32 (2) ◽  
pp. 025801
Author(s):  
Xiangrui Liu ◽  
Zhuang Li ◽  
Chengkun Shi ◽  
Bo Xiao ◽  
Run Fang ◽  
...  
Keyword(s):  
Output Power ◽  
High Power ◽  
Slope Efficiency ◽  
Laser Emission ◽  
Continuous Wave ◽  
Optical Glass ◽  
Maximum Output Power ◽  
Glass Plate ◽  
Maximum Output ◽  
First Time

Abstract We demonstrated 22 W LD-pumped high-power continuous-wave (CW) deep red laser operations at 718.5 and 720.8 nm based on an a-cut Pr3+:YLF crystal. The output power of both polarized directions reached the watt-level without output power saturation. A single wavelength laser operated at 720.8 nm in the π-polarized direction was achieved, with a high output power of 4.5 W and high slope efficiency of approximately 41.5%. To the best of our knowledge, under LD-pumped conditions, the laser output power and slope efficiency are the highest at 721 nm. By using a compact optical glass plate as an intracavity etalon, we suppressed the π-polarized 720.8 nm laser emission. And σ-polarized single-wavelength laser emission at 718.5 nm was achieved, with a maximum output power of 1.45 W and a slope efficiency of approximately 17.8%. This is the first time that we have achieved the σ-polarized laser emission at 718.5 nm generated by Pr3+:YLF lasers.

Design and Analysis of a High Power Density, Low Temperature Waste Heat Recovery System Using an Oil-Free Turboalternator

2010 ◽  
Author(s):  
James F. Walton ◽  
Andrew Hunsberger ◽  
Hooshang Heshmat
Keyword(s):  
Output Power ◽  
Waste Heat ◽  
Maximum Output Power ◽  
Output Power Level ◽  
Working Fluid ◽  
Prototype System ◽  
Low Grade ◽  
Maximum Output ◽  
Test Results ◽  
Study Results

In this paper the authors will present the design and preliminary test results for a distributed electric generating system that uses renewable energy source for economical load-following and peak-shaving capability in an oil-free, high-speed micro-turboalternator system using compliant foil bearings and a permanent magnet alternator. Test results achieved with the prototype system operating to full speed and under power generating mode will be presented. A comparison between predicted and measured electrical output will also be presented up to a power generating level of 25 kWe at approximately 55,000 rpm. The excellent correlation between design and test provides the basis for scale up to larger power levels. Based upon the turboalternator test results a thermodynamic cycle analysis of a system using low grade waste heat water at approximately 100 C will be reviewed. The tradeoff study results for a series of environmentally friendly refrigerant working fluids will also be presented including sensitivity to vaporization and condensing temperatures. Based on the cycle and pinch point analyses predicted maximum output power was determined. Finally a preliminary turbine design for the selected R134a working fluid was completed. The results of this study show that a net output power level of greater than 40 kW is possible for approximately 240 l/m flow of water at 100C is possible.

Modelling of Mechanical Nonlinearity in an Electromagnetic Vibration Energy Harvester Using a Forced Duffing Equation

2012 ◽  
Author(s):  
S. D. Moss ◽  
L. A. Vandewater ◽  
S. C. Galea
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Duffing Oscillator ◽  
Maximum Output Power ◽  
Vibration Energy ◽  
Maximum Output ◽  
Vibration Energy Harvesting ◽  
Vibration Energy Harvester ◽  
Homotopy Analysis ◽  
Wire Coil

This work reports on the modelling and experimental validation of a bi-axial vibration energy harvesting approach that uses a permanent-magnet/ball-bearing arrangement and a wire-coil transducer. The harvester’s behaviour is modelled using a forced Duffing oscillator, and the primary first order steady state resonant solutions are found using the homotopy analysis method (or HAM). Solutions found are shown to compare well with measured bearing displacements and harvested output power, and are used to predict the wideband frequency response of this type of vibration energy harvester. A prototype harvesting arrangement produced a maximum output power of 12.9 mW from a 12 Hz, 500 milli-g (or 4.9 m/s2) rms excitation.

Sign in / Sign up

Export Citation Format

Share Document