scholarly journals Extraction of the electrical parameters of the Au/InSb/InP Schottky diode in the temperature range (300 K- 425 K)

2020 ◽  
Vol 5 (1) ◽  
pp. 30
Author(s):  
Ali Sadoun
Keyword(s):  
Schottky Barrier ◽  
Barrier Height ◽  
Schottky Diode ◽  
Ideality Factor ◽  
Schottky Barrier Height ◽  
Theoretical Study ◽  
Series Resistance ◽  
Electrical Parameters ◽  
Temperature Range ◽  
Current Voltage

In this work, we have presented a theoretical study of  Au/InSb/InP Schottky diode based on current-voltage (I-V) measurement in the temperature range ( 300 K- 425 K). Electrical parameters of Au/InSb/InP such as barrier height (Φb), ideality factor and series resistance have been calculated by employing the conventional (I-V), Norde, Cheung and Chattopadhyay methods. Measurements show that the Schottky barrier height (SBH), ideality factor and series resistance, RS for Au/InSb/InP Schottky diode in the temperature range (300 K–425 K)  are 0.602-0.69eV, 1.683-1.234 and 84.54-18.95 (Ω), respectively. These parameters were extracted using Atlas-Silvaco-Tcad logical.

Effect of Indentation on I-V Characteristics of Au/n-GaAs Schottky Barrier Diodes

2008 ◽  
Vol 63 (3-4) ◽  
pp. 199-202 ◽  
Author(s):  
Ahmet Faruk Ozdemir ◽  
Adnan Calik ◽  
Guven Cankaya ◽  
Osman Sahin ◽  
Nazim Ucar
Keyword(s):  
Schottky Barrier ◽  
Barrier Height ◽  
Schottky Diode ◽  
Ideality Factor ◽  
Room Temperature ◽  
Schottky Barrier Height ◽  
Vickers Microhardness ◽  
Schottky Barrier Diodes ◽  
Microhardness Test ◽  
Current Voltage

Au/n-GaAs Schottky barrier diodes (SBDs) have been fabricated. The effect of indentation on Schottky diode parameters such as Schottky barrier height (φb) and ideality factor (n) was studied by current-voltage (I-V) measurements. The method used for indentation was the Vickers microhardness test at room temperature. The experimental results showed that the I-V characteristics move to lower currents due to an increase of φb with increasing indentation weight, while contacts showed a nonideal diode behaviour.

Analysis of current–voltage and capacitance–voltage characteristics of Zr/p-Si Schottky diode with high series resistance

2020 ◽  
Vol 34 (10) ◽  
pp. 2050095
Author(s):  
Durmuş Ali Aldemir
Keyword(s):  
Barrier Height ◽  
Schottky Diode ◽  
Ideality Factor ◽  
Series Resistance ◽  
Zero Bias ◽  
Acceptor Concentration ◽  
Current Voltage ◽  
Capacitance Voltage ◽  
High Series ◽  
Contact Parameters

Zr/p-Si Schottky diode was fabricated by DC magnetic sputtering of Zr on p-Si. Zr rectifying contact gave a zero bias barrier height of 0.73 eV and an ideality factor of 1.33 by current–voltage measurement. The experimental zero bias barrier height was higher than the value predicted by metal-induced gap states (MIGSs) and electronegativity theory. The forward bias current was limited by high series resistance. The series resistance value of 9840 [Formula: see text] was determined from Cheung functions. High value of the series resistance was ascribed to low quality ohmic contact. In addition to Cheung functions, important contact parameters such as barrier height and series resistance were calculated by using modified Norde method. Re-evaluation of modified Norde functions was realized in the direction of the method proposed by Lien et al. [IEEE Trans. Electron Devices 31 (1984) 1502]. From the method, the series resistance and ideality factor values were found to be as 41.49 [Formula: see text] and 2.08, respectively. The capacitance–voltage characteristics of the diode were measured as a function of frequency. For a wide range of applied frequency, the contact parameters calculated from [Formula: see text]–[Formula: see text] curves did not exhibit frequency dependence. The barrier height value of 0.71 eV which was in close agreement with the value of zero bias barrier height was calculated from [Formula: see text]–[Formula: see text] plot at 1 MHz. The values of acceptor concentration obtained from [Formula: see text]–[Formula: see text] curves showed consistency with actual acceptor concentration of p-Si.

Gaussian distribution of Schottky barrier heights on SnO2 nanowires

2011 ◽  
Vol 1406 ◽  
Author(s):  
Cleber A. Amorim ◽  
Olivia M. Berengue ◽  
Luana Araújo ◽  
Edson R. Leite ◽  
Adenilson J. Chiquito
Keyword(s):  
Schottky Barrier ◽  
Barrier Height ◽  
Ideality Factor ◽  
Schottky Barrier Height ◽  
Series Resistance ◽  
Small Deviation ◽  
Thermionic Emission ◽  
Barrier Heights ◽  
Sno2 Nanowires ◽  
Different Temperatures

ABSTRACTIn this work, we studied metal/SnO2 junctions using transport properties. Parameters such as barrier height, ideality factor and series resistance were estimated at different temperatures. Schottky barrier height showed a small deviation of the theoretical value mainly because the barrier was considered fixed as described by ideal thermionic emission-diffusion model. These deviations have been explained by assuming the presence of barrier height inhomogeneities. Such assumption can also explain the high ideality factor as well as the Schottky barrier height and ideality factor dependence on temperature.

Electrical Properties Dependent on Schottky Diode Pd/PSC-pSi(100) Based on Hydrocarbon Gas Sensor

2009 ◽  
Vol 609 ◽  
pp. 195-199
Author(s):  
A. Keffous ◽  
M. Kechouane ◽  
Tahar Kerdja ◽  
Y. Belkacem ◽  
K. Bourenane ◽  
...  
Keyword(s):  
Electrical Properties ◽  
Barrier Height ◽  
Schottky Diode ◽  
Ideality Factor ◽  
Gas Sensing ◽  
Series Resistance ◽  
Schottky Diodes ◽  
Electrical Parameters ◽  
Porous Sic ◽  
Sic Films

In this paper we present the study of a Schottky diode gas sensing by using porous SiC films with palladium as a catalytic metal. The Schottky diodes were used for the first time for hydrocarbon (C2H6) gas sensing. The properties of the porous SiC films formed by electrochemical method were investigated by scanning electron microscopy (SEM). The electrical measurements were made at room temperature (295 K) in different ambient. The effect of the porous surface structure was investigated by evaluating electrical parameters such as the ideality factor (n), barrier height (Bp) and series resistance (Rs). The porous layer significantly affects the electrical properties of the Schottky diodes. Analysis of current-voltage (I-V) characteristics showed that the forward current might be described by a classical thermal emission theory. The ideality factor determined by the I–V characteristics was found to be dependent on the SiC thickness. For a thinner SiC layer (0.16 µm), the electrical parameters n was found around 1.135, 0.7041 eV for a barrier height and 45  for a series resistance, but for a thicker one (1.6 µm) n, Bp and Rs were 1.368, 0.7756 eV and 130 , respectively. The low value of the series resistance obtained using Cheung’s method clearly indicated the high performance of the Schottky diode for thinner SiC layer. This effect showed the uniformity of the SiC layer. Finally, sensitivity around 66 % and selectivity of the sensors were reached by using the PSC layer at low voltages below 0.5 Volt.

scholarly journals High Voltage Graphene Nanowall Trench MOS Barrier Schottky Diode Characterization for High Temperature Applications

2019 ◽  
Vol 9 (8) ◽  
pp. 1587
Author(s):  
Rahimah Mohd Saman ◽  
Sharaifah Kamariah Wan Sabli ◽  
Mohd Rofei Mat Hussin ◽  
Muhammad Hilmi Othman ◽  
Muhammad Aniq Shazni Mohammad Haniff ◽  
...  
Keyword(s):  
High Temperature ◽  
Schottky Barrier ◽  
Barrier Height ◽  
Leakage Current ◽  
Barrier Layer ◽  
Ideality Factor ◽  
Schottky Barrier Height ◽  
Series Resistance ◽  
Measurement Data ◽  
Industrial Sectors

Graphene’s superior electronic and thermal properties have gained extensive attention from research and industrial sectors to study and develop the material for various applications such as in sensors and diodes. In this paper, the characteristics and performance of carbon-based nanostructure applied on a Trench Metal Oxide Semiconductor MOS barrier Schottky (TMBS) diode were investigated for high temperature application. The structure used for this study was silicon substrate with a trench and filled trench with gate oxide and polysilicon gate. A graphene nanowall (GNW) or carbon nanowall (CNW), as a barrier layer, was grown using the plasma enhanced chemical vapor deposition (PECVD) method. The TMBS device was then tested to determine the leakage current at 60 V under various temperature settings and compared against a conventional metal-based TMBS device using TiSi2 as a Schottky barrier layer. Current-voltage (I-V) measurement data were analyzed to obtain the Schottky barrier height, ideality factor, and series resistance (Rs) values. From I-V measurement, leakage current measured at 60 V and at 423 K of the GNW-TMBS and TiSi2-TMBS diodes were 0.0685 mA and above 10 mA, respectively, indicating that the GNW-TMBS diode has high operating temperature advantages. The Schottky barrier height, ideality factor, and series resistance based on dV/dln(J) vs. J for the GNW were calculated to be 0.703 eV, 1.64, and 35 ohm respectively.

scholarly journals Investigation, analysis and comparison of current-voltage characteristics for Au/Ni/GaN Schottky structure using I-V-T simulation

2019 ◽  
Vol 37 (3) ◽  
pp. 496-502 ◽  
Author(s):  
A. Sadoun ◽  
S. Mansouri ◽  
M. Chellali ◽  
N. Lakhdar ◽  
A. Hima ◽  
...  
Keyword(s):  
Experimental Data ◽  
Barrier Height ◽  
Theoretical Study ◽  
Series Resistance ◽  
Electrical Parameters ◽  
Current Voltage ◽  
Temperature Ranges ◽  
Current Voltage Characteristics ◽  
Schottky Structure ◽  
Good Agreement

AbstractIn this work, we have presented a theoretical study of Au/Ni/GaN Schottky diode based on current-voltage (I-V) measurement for temperature range of 120 K to 400 K. The electrical parameters of Au/Ni/GaN, such as barrier height (Φb), ideality factor and series resistance have been calculated employing the conventional current-voltage (I-V), Cheung and Chattopadhyay method. Also, the variation of Gaussian distribution (P (Φb)) as a function of barrier height (Φb) has been studied. Therefore, the modified ( {( {\ln \left( {{{{\rm{I}}_0 } \over {{\rm{T}}^2 }}} \right) - \left( {{{{\rm{q}}^2 \sigma _{{\rm{s}}0}^2 } \over {2{\rm{kT}}^2 }}} \right) = \ln ( {{\rm{AA}}^*} ) - {{{\rm{q}}\emptyset_{{\rm B}0} } \over {{\rm{kT}}}}} ){\rm{vs}}.( {{1 \over {{\rm{kT}}}}} )} ) relation has been extracted from (I-V) characteristics, where the values of ΦB0 and {\rm{A}}_{{\rm{Simul}}}^* have been found in different temperature ranges. The obtained results have been compared to the existing experimental data and a good agreement was found.

Temperature Dependent Current-Voltage Characteristics of Pt/MoS2 Schottky Junction

MRS Advances ◽  
2019 ◽  
Vol 4 (38-39) ◽  
pp. 2127-2134
Author(s):  
Neetika ◽  
Ramesh Chandra ◽  
V. K. Malik
Keyword(s):  
Band Gap ◽  
Schottky Barrier ◽  
Barrier Height ◽  
Ideality Factor ◽  
Schottky Barrier Height ◽  
Schottky Junction ◽  
Transition Metal Dichalcogenide ◽  
Dc Sputtering ◽  
Current Voltage ◽  
Dc Sputtering Technique

AbstractMolybdenum disulphide (MoS2) is one of the transition metal dichalcogenide (TMD) materials which has attracted attention due to its various interesting properties. MoS2 is very promising for electronic and optoelectronic devices due to its indirect band gap (∼1.2 eV) for few layer and direct band gap (∼1.8 eV) for monolayer MoS2. In MoS2 based Schottky devices, Schottky barrier height depends on the thickness of MoS2 because of its tunable electronic properties. Here, we have used DC sputtering technique to fabricate metal-semiconductor junction of MoS2 with platinum (Pt) metal contacts. In this work, MoS2 thin film (∼10 nm) was deposited on p-Silicon (111) using DC sputtering technique at optimized parameters. Schottky metallization of Pt metal (contact area ∼ 0.785x10-2 cm2) was also done using DC sputtering. Current-voltage (I-V) characteristics of the Pt/MoS2 Schottky junction have been investigated in the temperature range 80-350K. Forward I-V characteristics of Pt/MoS2 junction are analysed to calculate different Schottky parameters. Schottky barrier height increases and ideality factor decreases on increasing the temperature from 80-350K. The I-V-T measurements suggest the presence of local inhomogeneities at the Pt/MoS2 junction. Schottky barrier inhomogeneities occur in case of rough interface. In such cases, the Schottky barrier height does not remain constant and vary locally. Current transport through the Schottky junction is a thermally activated process. As temperature increases, more and more electrons overcome the spatially inhomogeneous barrier height. As a result, the ideality factor becomes close to unity and apparent barrier height increases due to increase in temperature.

THE EFFECT OF NANO AND MICRO POROSITY ON THE SCHOTTKY BARRIER HEIGHT AND IDEALITY FACTOR IN THE I–V CHARACTERISTICS OF PtSi/p-Si IR DETECTOR

2009 ◽  
Vol 23 (05) ◽  
pp. 765-771
Author(s):  
H. ESHGHI ◽  
M. MOHAMMADI
Keyword(s):  
Schottky Barrier ◽  
Barrier Height ◽  
Ideality Factor ◽  
Schottky Barrier Height ◽  
Thermionic Emission ◽  
Ir Detector ◽  
Current Voltage ◽  
Two Samples ◽  
P Type ◽  
Silicon Interface

In this paper, the effect of porosity on reverse bias current–voltage characteristics of PtSi/por - Si (p-type) IR detector as a function of temperature is investigated. Our experimental data for two samples with different porosities (50% and 10%) at 300 K and 77 K are reported by Raissi et al.1 These data indicates a breakdown-like behavior. Our analytical model is based on hole thermionic emission with large ideality factor (n ≈ 200). Our calculations show that at each temperature, the Schottky barrier height, as well as the ideality factor, in sample with 10% porosity is bigger than that of 50%. These variations could be due to band gap variations of Si size effect using quantum dot model, and the presence of the relatively high (~1015 cm-2 eV-1) density of states at the silicide/por-silicon interface, respectively.

Sign in / Sign up

Export Citation Format

Share Document