Utilization of Powdered EPDM Scrap in EPDM Compound

2003 ◽  
Vol 76 (1) ◽  
pp. 36-59 ◽  
Author(s):  
Ceni Jacob ◽  
A. K. Bhowmick ◽  
P. P. De ◽  
S. K. De
Keyword(s):  
Silicon Carbide ◽  
Particle Size ◽  
Particle Surface ◽  
Die Swell ◽  
Mild Oxidation ◽  
Abrasive Wheel ◽  
Waste Rubber ◽  
Curing Characteristics ◽  
Average Size ◽  
Extrudate Distortion

Abstract Processability, curing characteristics and vulcanizate properties of EPDM compounds containing ground waste EPDM (W-EPDM) have been studied. Ground waste was prepared from factory scraps, using a mechanical grinder with silicon carbide abrasive wheel rotating at 2950 rpm. The particle size shows a range between 2 and 50 μm, with an average size of 10 μm. Particle surface seems to be rough and convoluted and mild oxidation during the abrasion enhances the aggregation of particles. Mooney scorch time and the maximum rheometric torque of the EPDM compound decrease gradually with increasing W-EPDM content. Migration of curatives between the virgin rubber and waste rubber phases is believed to be the reason for the variation in the curing behavior. The processability of the EPDM compound shows improvement on addition of W-EPDM (that is, both die swell and extrudate distortion are less). The vulcanizate properties of the W-EPDM-filled EPDM compounds reveal the reinforcing nature of the ultrafine W-EPDM particles. Comparison of W-EPDM with an inert filler like precipitated CaCO3 in an EPDM compound reveals the potential of W-EPDM as a cheap filler in EPDM compounds. It is also found that W-EPDM can be incorporated into the window seal compound formulation and the drop in properties even at 100 phr of W-EPDM is within acceptable limit, thus providing a scope for on-site recycling of EPDM.

scholarly journals ZnWO4 Nanoparticle Scintillators for High Resolution X-ray Imaging

Nanomaterials ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1721
Author(s):  
Heon Yong Jeong ◽  
Hyung San Lim ◽  
Ju Hyuk Lee ◽  
Jun Heo ◽  
Hyun Nam Kim ◽  
...  
Keyword(s):  
Particle Size ◽  
Zinc Oxide ◽  
High Resolution ◽  
Tungsten Oxide ◽  
Spatial Resolution ◽  
High Spatial Resolution ◽  
X Ray ◽  
X Ray Imaging ◽  
Average Size ◽  
And Tungsten

The effect of scintillator particle size on high-resolution X-ray imaging was studied using zinc tungstate (ZnWO4) particles. The ZnWO4 particles were fabricated through a solid-state reaction between zinc oxide and tungsten oxide at various temperatures, producing particles with average sizes of 176.4 nm, 626.7 nm, and 2.127 μm; the zinc oxide and tungsten oxide were created using anodization. The spatial resolutions of high-resolution X-ray images, obtained from utilizing the fabricated particles, were determined: particles with the average size of 176.4 nm produced the highest spatial resolution. The results demonstrate that high spatial resolution can be obtained from ZnWO4 nanoparticle scintillators that minimize optical diffusion by having a particle size that is smaller than the emission wavelength.

A Convenient Method for Preparing Well-Dispersed Er2Zr2O7 Nanocrystals

2010 ◽  
Vol 123-125 ◽  
pp. 611-614 ◽  
Author(s):  
Yu Ping Tong ◽  
Rui Zhu Zhang ◽  
Shun Bo Zhao ◽  
Chang Yong Li
Keyword(s):  
Particle Size ◽  
Combustion Synthesis ◽  
Crystal Size ◽  
Lattice Distortion ◽  
Combustion Method ◽  
Treatment Temperature ◽  
Synthesis Process ◽  
Thermal Treatment Temperature ◽  
Average Size ◽  
Xrd And Tem

Well-dispersed fluorite Er2Zr2O7 nanocrystals have been successfully prepared by a convenient salt-assistant combustion method. The effects of calcinations temperature and salt category on the characteristics of the products were investigated by XRD and TEM. The thermal treatment temperature has an important effect on crystal size and lattice distortion of the nanocrystals. The experiment showed that the introduction of salt in the combustion synthesis process resulted in the formation of well-dispersed Er2Zr2O7 nanocrystals. The average size was 30 nm and was in agreement with the XRD result, which indicated that the nanocrystals were uniform in particle size distribution. Moreover, the possible formation process in the salt-assisted combustion synthesis was also analyzed.

scholarly journals Modulation of Lithium Disilicate Translucency through Heat Treatment

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2094
Author(s):  
Seok-Ki Jung ◽  
Dae Woon Kim ◽  
Jeongyol Lee ◽  
Selvaponpriya Ramasamy ◽  
Hyun Sik Kim ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Particle Size ◽  
Light Scattering ◽  
Flexural Strength ◽  
Control Method ◽  
Light Transmission ◽  
Lithium Disilicate ◽  
Lower Heat ◽  
Average Size ◽  
Ball Test

The aim of this study was to present a control method for modulating the translucency of lithium disilicate ceramics through thermal refinement. Identical lithium disilicate blocks were thermally refined using four different heat treatment schedules, and the microstructure, translucency, and flexural strength of the ceramics were investigated in detail by SEM, spectroscopy, and a piston-on-three-ball test. The results showed that ceramics treated under higher heat had larger grains, with an average size between 240 and 1080 nm. In addition, a higher transmittance of all wavelengths was observed in ceramics treated under lower heat, and the transmittance in the 550 nm wavelength ranged from 27 to 34%. The results suggest that the translucency of ceramics can be modified through thermal refinement under two conditions: (1) the particle size of the ceramic is small enough to achieve minimal grain-boundary light scattering, and (2) the percentage of particles allowing visible light transmission is altered by the heat treatment.

scholarly journals Ice nucleation abilities of soot particles determined with the Horizontal Ice Nucleation Chamber

2018 ◽  
Vol 18 (18) ◽  
pp. 13363-13392 ◽  
Author(s):  
Fabian Mahrt ◽  
Claudia Marcolli ◽  
Robert O. David ◽  
Philippe Grönquist ◽  
Eszter J. Barthazy Meier ◽  
...  
Keyword(s):  
Particle Size ◽  
Water Saturation ◽  
Particle Surface ◽  
Water Vapor Sorption ◽  
Contact Angles ◽  
Ice Nucleation ◽  
Particle Surface Area ◽  
Soot Particles ◽  
Microphysical Properties ◽  
Homogeneous Freezing

Abstract. Ice nucleation by different types of soot particles is systematically investigated over the temperature range from 218 to 253 K relevant for both mixed-phase (MPCs) and cirrus clouds. Soot types were selected to represent a range of physicochemical properties associated with combustion particles. Their ice nucleation ability was determined as a function of particle size using relative humidity (RH) scans in the Horizontal Ice Nucleation Chamber (HINC). We complement our ice nucleation results by a suite of particle characterization measurements, including determination of particle surface area, fractal dimension, temperature-dependent mass loss (ML), water vapor sorption and inferred porosity measurements. Independent of particle size, all soot types reveal absence of ice nucleation below and at water saturation in the MPC regime (T>235 K). In the cirrus regime (T≤235 K), soot types show different freezing behavior depending on particle size and soot type, but the freezing is closely linked to the soot particle properties. Specifically, our results suggest that if soot aggregates contain mesopores (pore diameters of 2–50 nm) and have sufficiently low water–soot contact angles, they show ice nucleation activity and can contribute to ice formation in the cirrus regime at RH well below homogeneous freezing of solution droplets. We attribute the observed ice nucleation to a pore condensation and freezing (PCF) mechanism. Nevertheless, soot particles without cavities of the right size and/or too-high contact angles nucleate ice only at or well above the RH required for homogeneous freezing conditions of solution droplets. Thus, our results imply that soot particles able to nucleate ice via PCF could impact the microphysical properties of ice clouds.

scholarly journals Effect of Home Grinding on Properties of Brewed Coffee

2014 ◽  
Vol 4 (1) ◽  
pp. 77
Author(s):  
Christopher Murray ◽  
Thamara Laredo
Keyword(s):  
Particle Size ◽  
Fourier Transform ◽  
Distribution Density ◽  
Particle Surface ◽  
Particle Surface Area ◽  
Present Evidence ◽  
Caffeine Content ◽  
General Recommendation ◽  
Grinding Time ◽  
Ground Coffee

<p>We present measurements of particle size distribution, density, loss of coffee on brewing and caffeine content in brewed coffee (as measured using Fourier Transform Infrared Spectroscopy) as a function of grinding time using a blade-type grinder. In general, there is not a lack of correlation between coffee properties and grinding for grinding times in excess of 42 s, but mass loss on brewing and caffeine content are both increased with grinding times between 0 and 42 s. In addition, we present evidence that this dependence of the composition of brewed coffee on grinding time is a function of increased coffee particle surface area that results from grinding, rather than increased loss of grounds into the brewed beverage or increased percolation time. Finally, we present a general recommendation for determining equivalency between small amounts of finely ground coffee and larger amounts of coarser-ground coffee.</p>

Microwave Synthesis of Silicon Carbide Nano Powders with Silicon and Carbon

2014 ◽  
Vol 602-603 ◽  
pp. 118-121
Author(s):  
You Jun Lu ◽  
Hong Fang Shen ◽  
Sheng Wei Guo
Keyword(s):  
Silicon Carbide ◽  
Particle Size ◽  
Microwave Heating ◽  
Chemical Reaction ◽  
Crystalline Phase ◽  
Microwave Synthesis ◽  
Time Effects ◽  
Xrd Patterns

Nanosized silicon carbide powders were synthesized from a mixture of silicon and carbon by microwave heating methods. The Result Indicates SiC can be formed at lower temperatures by using the Si-C reaction at 1200°C for 30min. XRD patterns shows that SiC peaks appeared as the only crystalline phase. SEM photo shows the particle size was 100～200 nanometer. At the same time, Effects of chemical reaction of silicon and carbon was researched by mechanical activated microwave synthesis.

scholarly journals On the contribution of Aitken mode particles to cloud droplet populations at continental background areas – a parametric sensitivity study

2007 ◽  
Vol 7 (3) ◽  
pp. 6077-6112
Author(s):  
T. Anttila ◽  
V.-M. Kerminen
Keyword(s):  
Surface Tension ◽  
Particle Size ◽  
Chemical Composition ◽  
Pure Water ◽  
Particle Surface ◽  
Chemical Properties ◽  
Sensitivity Study ◽  
Geometric Standard Deviation ◽  
Cloud Droplets ◽  
Aitken Mode

Abstract. Aitken mode particles are potentially an important source of cloud droplets in continental background areas. In order to find out which physico-chemical properties of Aitken mode particles are most important regarding their cloud-nucleating ability, we applied a global sensitivity method to an adiabatic air parcel model simulating the number of cloud droplets formed on Aitken mode particles, CD2. The technique propagates uncertainties in the parameters describing the properties of Aitken mode to CD2. The results show that if the Aitken mode particles do not contain molecules that are able to reduce the particle surface tension more than 30% and/or decrease the mass accommodation coefficient of water, α, below 10−2, the chemical composition and modal properties may have roughly an equal importance at low updraft velocities characterized by maximum supersaturations <0.1%. For larger updraft velocities, however, the particle size distribution is clearly more important than the chemical composition. In general, CD2 exhibits largest sensitivity to the particle number concentration, followed by the particle size. Also the shape of the particle mode, characterized by the geometric standard deviation (GSD), can be as important as the mode mean size at low updraft velocities. Finally, the performed sensitivity analysis revealed also that the chemistry may dominate the total sensitivity of CD2 to the considered parameters if: 1) the value of α varies at least one order of magnitude more than what is expected for pure water surfaces (10−2–1), or 2) the particle surface tension varies more than roughly 30% under conditions close to reaching supersaturation.

scholarly journals Self-Cleaning Limestone Paint Modified by Nanoparticles TiO2 Synthesized from TiCl3 as Precursors and PEG6000 as Dispersant

2017 ◽  
Vol 12 (3) ◽  
pp. 351 ◽  
Author(s):  
Nur Fadhilah ◽  
Niki Etruly ◽  
Maktum Muharja ◽  
Dyah Sawitri
Keyword(s):  
Particle Surface ◽  
Wall Painting ◽  
Reaction Engineering ◽  
Mass Ratio ◽  
Particle Surface Area ◽  
Surface Tension Reduction ◽  
Agglomeration Process ◽  
Activating Agent ◽  
Self Cleaning ◽  
Average Size

Limestone is commonly used for wall painting, but it is easy to be dirty. In this study, a self-cleaning limestone paint was synthesized by modifying dispersant and TiO2 nanoparticles. The TiO2 that prepared by TiCl3 were functionalized with PEG6000 as a surface activating agent. The paint achieved highest impurity degradation of 83.11 % for the mass ratio of TiO2 and PEG6000 (MRTP) of 1: 6, in which TiO2 average size distribution was 75.81 µm2, the particle surface area of TiO2 was 2,544 µm2, and the smallest contact angle was 7°. It was found that the dispersant (PEG6000) significantly improved the self-cleaning ability of limestone paint. The surface tension reduction from PEG6000-modified prevented the agglomeration process of TiO2 and suggests that the limestone paint a good self-cleaning coating for wall painting. Copyright © 2017 BCREC Group. All rights reservedReceived: 21st November 2016; Revised: 10th September 2017; Accepted: 11st September 2017; Available online: 27th October 2017; Published regularly: December 2017How to Cite: Fadhilah, N., Etruly, N., Muharja, M., Sawitri, D. (2017). Self-Cleaning Limestone Paint Modified by Nanoparticles TiO2 Synthesized from TiCl3 as Precursors and PEG6000 as Dispersant. Bulletin of Chemical Reaction Engineering & Catalysis, 12(3): 351-356 (doi:10.9767/bcrec.12.3.800.351-356) 

scholarly journals Effect of the polymeric coating over Fe3O4 particles used for magnetic separation

2010 ◽  
Vol 8 (5) ◽  
pp. 1041-1046 ◽  
Author(s):  
Raúl Reza ◽  
Carlos Martínez Pérez ◽  
Claudia Rodríguez González ◽  
Humberto Romero ◽  
Perla García Casillas
Keyword(s):  
Particle Size ◽  
Magnetite Nanoparticles ◽  
Average Particle Size ◽  
Spherical Shape ◽  
Polymeric Coating ◽  
Average Particle ◽  
Synthesis Conditions ◽  
Aging Conditions ◽  
Magnetite Particles ◽  
Average Size

AbstractIn this work, the synthesis of magnetite nanoparticles by two variant chemical coprecipitation methods that involve reflux and aging conditions was investigated. The influence of the synthesis conditions on particle size, morphology, magnetic properties and protein adsorption were studied. The synthesized magnetite nanoparticles showed a spherical shape with an average particle size directly influenced by the synthesis technique. Particles of average size 27 nm and 200 nm were obtained. When the coprecipitation method was used without reflux and aging, the smallest particles were obtained. Magnetite nanoparticles obtained from both methods exhibited a superparamagnetic behavior and their saturation magnetization was particle size dependent. Values of 67 and 78 emu g−1 were obtained for the 27 nm and 200 nm magnetite particles, respectively. The nanoparticles were coated with silica, aminosilane, and silica-aminosilane shell. The influence of the coating on protein absorption was studied using Bovine Serum Albumin (BSA) protein.

Sign in / Sign up

Export Citation Format

Share Document