Inorganic-Framework Molecularly Imprinted CdS/TiO2 for Selectively Photocatalytic Degradation of Di (2-ethylhexyl) phthalate

2019 ◽  
Vol 41 (2) ◽  
pp. 308-308
Author(s):  
Fangyan Chen Fangyan Chen ◽  
Yiming Liu Yiming Liu ◽  
Xi Zhang Xi Zhang ◽  
Lina He and Yubin Tang Lina He and Yubin Tang
Keyword(s):  
Photoelectron Spectroscopy ◽  
Tetrabutyl Titanate ◽  
Template Molecule ◽  
Molecularly Imprinted ◽  
X Ray ◽  
Simulated Solar Light ◽  
Specific Recognition ◽  
Vis Spectroscopy ◽  
Inorganic Framework ◽  
Ethylhexyl Phthalate

In order to improve the photocatalytic efficiency and selectivity of di (2-ethylhexyl) phthalate (DEHP) under solar-driven, the inorganic-framework molecularly imprinted CdS/TiO2, named as MIP-CdS/TiO2, was prepared by using DEHP as template molecule and tetrabutyl titanate as titanium source and functional monomer. The as-prepared MIP-CdS/TiO2 was characterized by scanning electron microscopy (SEM), X-ray energy spectrum (EDS), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), UV-Vis Spectroscopy (UV-vis), X-ray photoelectron spectroscopy (XPS) and photoluminescence spectrum (PL). And the specific recognition and photocatalytic selectivity of MIP-CdS/TiO2 to DEHP were investigated. The results show that inorganic-framework molecular imprinting on the surface of CdS/TiO2 can result in existence of specific recognition sites of DEHP, extend and intensify the absorption visible light of CdS/TiO2, inhibit the recombination of the photo-induced electron-holes pairs. MIP-CdS/TiO2 has a specific recognition to DEHP. The binding selectivity coefficients of DEHP relative to its analogues DBP and DMP are 2.78 and 2.60, respectively. Compared with CdS/TiO2, MIP-CdS/TiO2 exhibits higher photocatalytic activity and selectivity for DEHP. Under simulated solar light irradiation, the degradation efficiency of DEHP photocatalyzed by MIP-CdS/TiO2 is 75.5%, which is 1.63 times as high as that of DEHP photocatalyzed by CdS/TiO2.

scholarly journals CO Preferential Photo-Oxidation in Excess of Hydrogen in Dark and Simulated Solar Light Irradiation over AuCu-Based Catalysts on SBA-15 Mesoporous Silica-Titania

Materials ◽  
2018 ◽  
Vol 11 (7) ◽  
pp. 1203 ◽  
Author(s):  
Isabel Barroso-Martín ◽  
Antonia Infantes-Molina ◽  
Aldo Talon ◽  
Loretta Storaro ◽  
Elena Rodríguez-Aguado ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Light Irradiation ◽  
Solar Light ◽  
X Ray ◽  
Preferential Oxidation Of Co ◽  
Simulated Solar Light ◽  
Solar Light Irradiation ◽  
Vis Spectroscopy ◽  
Average Size ◽  
Adsorption Desorption

In this work, SBA-15 silica and silica-titania have been used as supports for photocatalysts based on AuCu alloy (Au:Cu = 1) to be used in the preferential oxidation of CO (CO-PROX) in excess of hydrogen at room temperature and atmospheric pressure both in the dark and under simulated solar light irradiation. To study their textural, structural, chemical and optical properties, the samples were characterized by X-ray diffraction (XRD), high-resolution transmission electron microscopy (HR-TEM), adsorption-desorption of N2 at −196 °C, 13C and 29Si solid state nuclear magnetic resonance (NMR), X-ray photoelectron spectroscopy (XPS) and diffuse reflectance ultraviolet-visible (DRUV-vis) spectroscopy. Titanium was present mainly in the form of titania aggregates, but also as small particles interacting with the SBA support. In both catalysts, the metal alloy nanoparticles displayed an average size of 4 nm as demonstrated by TEM measurements. AuCu/Ti-SBA turned out to be photoactive and selective in the photo-CO-PROX reaction showing the highest activity, with conversion and selectivity towards CO2 of 80%, due both to the presence of titania incorporated in SBA-15 and to the synergistic effect of Cu when alloyed with Au.

scholarly journals Study on Synthesis and Photocatalytic Activity of Porous Titania Nanotubes

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Huang Liu ◽  
Yanhua Zhang ◽  
Hongtao Yang ◽  
Wei Xiao ◽  
Lanlan Sun
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Filter Paper ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Cellulose Nanofibers ◽  
Titania Nanotubes ◽  
Tetrabutyl Titanate ◽  
X Ray ◽  
Porous Titania

Using the common natural cellulose substance (filter paper) and triblock copolymer (Pluronic P123) micelles as dual templates, porous titania nanotubes with enhanced photocatalytic activity have been successfully synthesized through sol-gel methods. Firstly, P123 micelles were adsorbed onto the surfaces of cellulose nanofibers of filter paper, followed by hydrolysis and condensation of tetrabutyl titanate around these micelles to form titania layer. After calcination to remove the organic templates, hierarchical titania nanotubes with pores in the walls were obtained. The sample was characterized by X-ray diffraction pattern (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), nitrogen adsorption/desorption, Fourier Transform Infrared Spectroscopy (FT-IR), Ultraviolet-Visible Diffuse Reflectance Spectroscopy (UV-Vis DRS), and X-ray photoelectron spectroscopy (XPS). As compared with commercial P25 catalyst, the porous titania nanotubes prepared by this method displayed significantly enhanced photocatalytic activity for degrading methyl orange under UV irradiation. Within 10 minutes, the porous titania nanotubes are able to degrade over 70% of the original MO, while the value for the commercial Degussa P25 is only about 33%.

Silver mirror reaction metallized chromatography paper for supercapacitor application

2021 ◽  
Author(s):  
I-Hsuan Chen ◽  
Jung-Hsien Chang ◽  
Ren-Jie Xie ◽  
Chia-Hui Tseng ◽  
Sheng-Rong Hsieh ◽  
...  
Keyword(s):  
Flexible Electronics ◽  
Photoelectron Spectroscopy ◽  
Cost Effective ◽  
Water Contact ◽  
X Ray ◽  
Supercapacitor Application ◽  
Resource Limited ◽  
Vis Spectroscopy ◽  
Silver Mirror ◽  
Silver Mirror Reaction

Abstract In this study, the easy-to-operate silver mirror reaction (SMR) was used for metallizing chromatography paper. The SMR-metallized paper was characterized by water contact angle measurements, a surface profiler, X-ray photoelectron spectroscopy, UV-vis spectroscopy, X-ray diffraction, and electrical resistance measurement. The characterization results show that Ag was successfully synthesized on cellulose fibers and was electrically conductive after cyclic bending. Moreover, this SMR-metallized paper was used as electrodes for fabricating a supercapacitor. This SMR-metallized paper could be used for realizing cost-effective flexible electronics applied in on-site biochemical sensing in resource-limited settings.

scholarly journals Microwave-assisted preparation of ZnS and ZnSe nanocrystals with different morphologies for photodegradation process of organic dyes

2019 ◽  
Author(s):  
Katarzyna Matras-Postolek ◽  
A. Zaba ◽  
S. Sovinska ◽  
D. Bogdal
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Organic Dyes ◽  
Zinc Sulphide ◽  
Conventional Heating ◽  
Bet Surface Area ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Vis Spectroscopy

Zinc sulphide (ZnS) and zinc selenide (ZnSe) and manganese-doped and un-doped with different morphologies from 1D do 3D microflowers were successfully fabricated in only a few minutes by solvothermal reactions under microwave irradiation. In order to compare the effect of microwave heating on the properties of obtained  nanocrystals, additionally the synthesis under conventional heating was conducted additionally in similar conditions. The obtained nanocrystals were systematically characterized in terms of structural and optical properties using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), diffuse reflectance UV-Vis spectroscopy (DR UV-Vis), Fourier-transform infrared spectroscopy (FT-IR), photoluminescence spectroscopy (PL), X-ray photoelectron spectroscopy (XPS) and Brunauer-Emmett-Teller (BET) surface area analysis. The photocatalytic activity of ZnSe, ZnS, ZnS:Mn and ZnSe:Mn nanocrystals with different morphologies was evaluated by the degradation of methyl orange (MO) and Rhodamine 6G (R6G), respectively. The results show that Mn doped NCs samples had higher coefficient of degradation of organic dyes under ultraviolet irradiation (UV).

scholarly journals Effects of Different TiO2 Particle Sizes on the Microstructure and Optical Limiting Properties of TiO2/Reduced Graphene Oxide Nanocomposites

Nanomaterials ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 730 ◽  
Author(s):  
Yuyu Ren ◽  
Lili Zhao ◽  
Yang Zou ◽  
Lixin Song ◽  
Ningning Dong ◽  
...  
Keyword(s):  
Graphene Oxide ◽  
Reduced Graphene Oxide ◽  
Photoelectron Spectroscopy ◽  
Optical Limiting ◽  
Tio2 Particle ◽  
Tetrabutyl Titanate ◽  
Particle Sizes ◽  
X Ray ◽  
Reduced Graphene ◽  
Source Materials

TiO2/reduced graphene oxide (rGO) nanocomposites with two different TiO2 particle sizes were synthesized by a facile hydrothermal method using two different source materials of Ti: tetrabutyl titanate (TBT) and commercial TiO2 powder (P25). For respective series with the same source materials, we investigated additions that optimized the nonlinear optical properties (NLO) and optical limiting (OL) performances, and we explored the relationships between structural diversity and performance. Several characterization techniques, including X-ray powder diffraction (XRD), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), Fourier-transform infrared spectroscopy (FTIR), Raman spectroscopy, and diffuse reflectance ultraviolet-visible spectroscopy (UV-Vis) were conducted to confirm the microstructures and chemical states of as-prepared materials. This indicated the existence of the Ti–O–C bond between rGO sheets and TiO2 particles and the reduction from precursor graphene oxide (GO) to rGO. The results of UV-Vis spectra revealed that the TiO2/rGO nanocomposites showed smaller band gaps than bare TiO2. A nanosecond open-aperture Z-scan technique at 1064 nm was applied to investigate NLO and OL properties. TiO2/rGO nanocomposites exhibited enhanced NLO and OL performances, arising from synergistic effects, compared to individual components. The TBT series samples performed better than the P25 series, presumably relevant to dimensional effects.

scholarly journals Preparation of pod-shaped TiO 2 and Ag@TiO 2 nano burst tubes and their photocatalytic activity

2019 ◽  
Vol 6 (9) ◽  
pp. 191019 ◽  
Author(s):  
Shang Wang ◽  
Zhaolian Han ◽  
Tingting Di ◽  
Rui Li ◽  
Siyuan Liu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Oxalic Acid ◽  
Ultraviolet Light ◽  
Photoelectron Spectroscopy ◽  
Degradation Process ◽  
Catalytic Performance ◽  
Tetrabutyl Titanate ◽  
Order Kinetic ◽  
X Ray

The pod-shaped TiO 2 nano burst tubes (TiO 2 NBTs) were prepared by the combination of electrospinning and impregnation calcination with oxalic acid (H 2 C 2 O 4 ), polystyrene (PS) and tetrabutyl titanate. The silver nanoparticles (AgNPs) were loaded onto the surface of TiO 2 NBTs by ultraviolet light reduction method to prepare pod-shaped Ag@TiO 2 NBTs. In this work, we analysed the effect of the amount of oxalic acid on the cracking degree of TiO 2 NBTs; the effect of the concentration of AgNO 3 solution on the particle size and loading of AgNPs on the surface of TiO 2 NBTs. Scanning electron microscopy and transmission electron microscopy investigated the surface morphology of samples. X-ray diffraction and X-ray photoelectron spectroscopy characterized the structure and composition of samples. Rhodamine B (RhB) solution was used to evaluate the photocatalytic activity of pod-shaped TiO 2 NBTs and Ag@TiO 2 NBTs. The results showed that TiO 2 NBTs degraded 91.0% of RhB under ultraviolet light, Ag@TiO 2 NBTs degraded 95.5% under visible light for 75 and 60 min, respectively. The degradation process of both samples was consistent with the Langmuir–Hinshelwood first-order kinetic equation. Therefore, the catalytic performance of the sample is: Ag@TiO 2 NBTs > TiO 2 NBTs > TiO 2 nanotubes.

Photocatalytic Decomposition of Methylene Blue with Lanthanum Doping TiO2 under Visible Light Irradiation

2013 ◽  
Vol 734-737 ◽  
pp. 2163-2167
Author(s):  
Guang Xiu Cao ◽  
Zhong Hou Zhang ◽  
Bin Zhai
Keyword(s):  
Methylene Blue ◽  
Visible Light ◽  
Visible Light Irradiation ◽  
Photoelectron Spectroscopy ◽  
Light Irradiation ◽  
Photocatalytic Decomposition ◽  
Lanthanum Doping ◽  
X Ray ◽  
Degradation Rates ◽  
Vis Spectroscopy

Lanthanum doped TiO2 powders were prepared by hydrolysis of titanium tetra-n-butyl oxide and La (NO3)3 in solution. The resulting powders were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), UV-Vis absorption spectroscopy. The photocatalytic activities of doped samples were evaluated by the decomposition of methylene blue under visible light irradiation. The XRD results showed that the doping of lanthanum could not only efficiently inhibit the grain growth but also suppress the phase transition of anatase to rutile. UV-Vis spectroscopy of lanthanum doping TiO2 indicated that the absorption onset red-shifted to the visible light region. XPS results revealed that La2O3 had formed which could enhance the surface area. The degradation rates of methylene blue verified that the visible light photocatalytic activity of TiO2 has been enhanced by the doping of lanthanum.

scholarly journals Application of Reverse Micelle Sol–Gel Synthesis for Bulk Doping and Heteroatoms Surface Enrichment in Mo-Doped TiO2 Nanoparticles

Materials ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 937 ◽  
Author(s):  
Roberto Nasi ◽  
Serena Esposito ◽  
Francesca Freyria ◽  
Marco Armandi ◽  
Tanveer Gadhi ◽  
...  
Keyword(s):  
Tio2 Nanoparticles ◽  
Reverse Micelle ◽  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Actual State ◽  
Test Reaction ◽  
Potential Measurement ◽  
X Ray ◽  
Vis Spectroscopy ◽  
Mo Content

TiO2 nanoparticles containing 0.0, 1.0, 5.0, and 10.0 wt.% Mo were prepared by a reverse micelle template assisted sol–gel method allowing the dispersion of Mo atoms in the TiO2 matrix. Their textural and surface properties were characterized by means of X-ray powder diffraction, micro-Raman spectroscopy, N2 adsorption/desorption isotherms at −196 °C, energy dispersive X-ray analysis coupled to field emission scanning electron microscopy, X-ray photoelectron spectroscopy, diffuse reflectance UV–Vis spectroscopy, and ζ-potential measurement. The photocatalytic degradation of Rhodamine B (under visible light and low irradiance) in water was used as a test reaction as well. The ensemble of the obtained experimental results was analyzed in order to discover the actual state of Mo in the final materials, showing the occurrence of both bulk doping and Mo surface species, with progressive segregation of MoOx species occurring only at a higher Mo content.

Growth and Characterizations of Indium-Doped Pentacene Thinfilm Prepared by Thermal Co-Evaporation as a Novel Nanomaterial

2015 ◽  
Vol 1131 ◽  
pp. 35-38
Author(s):  
Navaphun Kayunkid ◽  
Annop Chanhom ◽  
Chaloempol Saributr ◽  
Adirek Rangkasikorn ◽  
Jiti Nukeaw
Keyword(s):  
Thin Films ◽  
Carrier Concentration ◽  
Photoelectron Spectroscopy ◽  
High Vacuum ◽  
Charge Carrier Mobility ◽  
Electrical Measurements ◽  
X Ray ◽  
Force Microscopy ◽  
Vis Spectroscopy ◽  
Hybrid Thin Films

This research is related to growth and characterizations of indium-doped pentacene thin films as a novel hybrid material. Doped films were prepared by thermal co-evaporation under high vacuum. The doping concentration was varied from 0% to 50% by controlling the different deposition rate between these two materials while the total thickness was fixed at 100 nm. The hybrid thin films were characterized by atomic force microscopy (AFM), X-ray diffraction (XRD) and UV-Visible spectroscopy to reveal the physical and optical properties. Moreover, the electrical properties of ITO/indium-doped-pentacene/Al devices i.e. charge mobility and carrier concentration were determined by considering the relationship between current-voltage and capacitance-voltage. AFM results identify that doping of indium into pentacene has an effect on surface properties of doped films i.e. the increase of surface grain size. XRD results indicate that doping of metal into pentacene has an effect on preferential orientation of pentacene’s crystalline domains. UV-Vis spectroscopy results show evolution of absorbance at photon energy higher than 2.7 eV corresponding to absorption from oxide of indium formed in the films. Electrical measurements exhibit higher conductivity in doped films resulting from increment of both charge carrier mobility and carrier concentration. Furthermore, chemical interactions taken place inside the doped films were investigated by x-ray photoelectron spectroscopy (XPS) in order to complete the remaining questions i.e. how do indium atoms interact with the neighbor molecules?, what is the origin of the absorption at E > 2.7 eV? Further results and discussions will be presented in the publication.

scholarly journals Photocatalytic Abatement of Volatile Organic Compounds by TiO2 Nanoparticles Doped with Either Phosphorous or Zirconium

Materials ◽  
2019 ◽  
Vol 12 (13) ◽  
pp. 2121 ◽  
Author(s):  
Melodj Dosa ◽  
Marco Piumetti ◽  
Samir Bensaid ◽  
Tahrizi Andana ◽  
Camilla Galletti ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Direct Synthesis ◽  
Ethylene Oxidation ◽  
Oxidation Reactions ◽  
X Ray ◽  
Binary Oxides ◽  
Ethylene Conversion ◽  
Vis Spectroscopy ◽  
Volatile Organic ◽  
Propylene Conversion

The aim of this work is to study the activity of novel TiO2-based photocatalysts doped with either phosphorus or zirconium under a UV-Vis source. A set of mesoporous catalysts was prepared by the direct synthesis: TiO2_A and TiO2_B (titanium oxide synthesized by two different procedures), P-TiO2 and Zr-TiO2 (binary oxides with either nonmetal or metal into the TiO2 framework). Complementary characterizations (N2 physisorption at 77 K, X-ray powder diffraction (XRD), field emission scanning electron microscopy (FESEM), energy dispersive X-ray (EDX) analysis, X-ray Photoelectron Spectroscopy (XPS), and (DR)UV-Vis spectroscopy) were used to investigate the physicochemical properties of the prepared catalysts. Then, the photocatalysts were tested for the oxidation of propylene and ethylene under UV-Vis light. As a result, the most promising catalyst for both the propylene and ethylene oxidation reactions was the P-TiO2 (propylene conversion = 27.8% and ethylene conversion = 13%, TOS = 3 h), thus confirming the beneficial effect of P-doping into the TiO2 framework on the photocatalytic activity.

Sign in / Sign up

Export Citation Format

Share Document