scholarly journals Studies on Exhaust Emissions from Copper-Coated Gasohol Run Spark Ignition Engine with Catalytic Converter

2011 ◽  
Vol 2011 ◽  
pp. 1-6
Author(s):  
S. Narasimha Kumar ◽  
K. Kishor ◽  
M. V. S. Murali Krishna ◽  
P. V. K. Murthy
Keyword(s):  
Compression Ratio ◽  
Iron Catalyst ◽  
Catalytic Converter ◽  
Exhaust Emissions ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Airflow Rate ◽  
Human Beings ◽  
Carbon Monooxide ◽  
Air Speed

The major pollutants emitted from spark ignition engine are carbon monooxide (CO) and unburnt hydrocarbons (UHC). These are hazardous and cause health problems to human beings, and hence control of these pollutants calls for immediate attention. Copper of thickness 300 microns is coated over piston crown and inside portion of the cylinder head of the spark ignition engine. Investigations have been carried out for reducing pollutants from a variable compression ratio, copper-coated spark ignition engine fitted with catalytic converter containing sponge iron catalyst run with gasohol (blend of 20% ethanol and 80% gasoline by volume). The influence of parameters such as void ratio, airflow rate, temperature of injected air, speed, compression ratio, and load of the engine on these emissions are studied. A microprocessor-based analyzer is used for the measurement of CO/UHC in the exhaust of the engine. The speed, load, compression ratio and the injection of air into the catalytic converter are found to show strong influence on reduction of the pollutants in the exhaust. Copper-coated spark ignition engine with gasohol operation reduced the exhaust emissions considerably when compared to conventional engine with pure gasoline operation.

Exhaust Emissions From a Stoichiometric, Ammonia and Gasoline Dual Fueled Spark Ignition Engine

2009 ◽  
Author(s):  
Shawn M. Grannell ◽  
Dennis N. Assanis ◽  
Donald E. Gillespie ◽  
Stanislav V. Bohac
Keyword(s):  
Nitric Oxide ◽  
Carbon Monoxide ◽  
Nitrous Oxide ◽  
Catalytic Converter ◽  
Exhaust Emissions ◽  
Spark Ignition ◽  
Oxygen Sensors ◽  
Spark Ignition Engine ◽  
Exhaust Gas

Engine-out and post-catalyst emissions of ammonia, hydrocarbons, nitric oxide, carbon monoxide, and nitrous oxide are measured for an ammonia and gasoline dual fueled spark ignition engine. An ordinary three-way catalytic converter can be used to clean up these emissions. The clean-up region occurs between stoichiometric and 0.2% rich. Ordinary exhaust gas oxygen sensors are usable with ammonia and gasoline in much the same way as they are with gasoline alone.

scholarly journals Ethanol/Gasoline Blends as Alternative Fuel in Last Generation Spark-Ignition Engines: A Review on CO and HC Engine Out Emissions

Energies ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 4034
Author(s):  
Paolo Iodice ◽  
Massimo Cardone
Keyword(s):  
Physicochemical Properties ◽  
Alternative Fuels ◽  
Experimental Studies ◽  
Alternative Fuel ◽  
Exhaust Emissions ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Spark Ignition Engine ◽  
Spark Ignition Engines ◽  
The Impact

Among the alternative fuels existing for spark-ignition engines, ethanol is considered worldwide as an important renewable fuel when mixed with pure gasoline because of its favorable physicochemical properties. An in-depth and updated investigation on the issue of CO and HC engine out emissions related to use of ethanol/gasoline fuels in spark-ignition engines is therefore necessary. Starting from our experimental studies on engine out emissions of a last generation spark-ignition engine fueled with ethanol/gasoline fuels, the aim of this new investigation is to offer a complete literature review on the present state of ethanol combustion in last generation spark-ignition engines under real working conditions to clarify the possible change in CO and HC emissions. In the first section of this paper, a comparison between physicochemical properties of ethanol and gasoline is examined to assess the practicability of using ethanol as an alternative fuel for spark-ignition engines and to investigate the effect on engine out emissions and combustion efficiency. In the next section, this article focuses on the impact of ethanol/gasoline fuels on CO and HC formation. Many studies related to combustion characteristics and exhaust emissions in spark-ignition engines fueled with ethanol/gasoline fuels are thus discussed in detail. Most of these experimental investigations conclude that the addition of ethanol with gasoline fuel mixtures can really decrease the CO and HC exhaust emissions of last generation spark-ignition engines in several operating conditions.

Simulation of Extended Expansion Lean Burn Spark Ignition Engine

2004 ◽  
Author(s):  
A. Manivannan ◽  
R. Ramprabhu ◽  
P. Tamilporai ◽  
S. Chandrasekaran
Keyword(s):  
Heat Transfer ◽  
Compression Ratio ◽  
Thermal Efficiency ◽  
Numerical Study ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Valve Closure ◽  
Intake Valve ◽  
Lean Burn ◽  
Atkinson Cycle

This paper deals with Numerical Study of 4-stoke, Single cylinder, Spark Ignition, Extended Expansion Lean Burn Engine. Engine processes are simulated using thermodynamic and global modeling techniques. In the simulation study following process are considered compression, combustion, and expansion. Sub-models are used to include effect due to gas exchange process, heat transfer and friction. Wiebe heat release formula was used to predict the cylinder pressure, which was used to find out the indicated work done. The heat transfer from the cylinder, friction and pumping losses also were taken into account to predict the brake mean effective pressure, brake thermal efficiency and brake specific fuel consumption. Extended Expansion Engine operates on Otto-Atkinson cycle. Late Intake Valve Closure (LIVC) technique is used to control the load. The Atkinson cycle has lager expansion ratio than compression ratio. This is achieved by increasing the geometric compression ratio and employing LIVC. Simulation result shows that there is an increase in thermal efficiency up to a certain limit of intake valve closure timing. Optimum performance is attained at 90 deg intake valve closure (IVC) timing further delaying the intake valve closure reduces the engine performance.

Sign in / Sign up

Export Citation Format

Share Document