scholarly journals Effects of Platinum and Palladium Metals on Ni/Mg1-xZrxO Catalysts in the CO2 Reforming of Methane

2018 ◽  
Vol 13 (2) ◽  
pp. 295 ◽  
Author(s):  
Faris Jasim Abdulridha Al-Doghachi
Keyword(s):  
Photoelectron Spectroscopy ◽  
Thermo Gravimetric Analysis ◽  
Coke Formation ◽  
Dry Reforming Of Methane ◽  
Precipitation Method ◽  
Cubic Phase ◽  
Gravimetric Analysis ◽  
Co2 Reforming ◽  
X Ray ◽  
Co2 Reforming Of Methane

Nickel, palladium, and platinum catalysts (1 wt.% each) supported on MgO and MgZrO to prepare Pt,Pd,Ni/Mg1-xZrxO catalysts (where x = 0, 0.03, 0.07, and 0.15), were synthesized by using co-precipitation method with K2CO3 as the precipitant. X-ray diffraction (XRD), X-ray fluorescence (XRF), X-ray photoelectron spectroscopy (XPS), Brunauer–Emmett–Teller (BET), transmission electron microscopy (TEM), H2-temperature programmed reduction (H2-TPR), and thermo gravimetric analysis (TGA) were employed to observe the characteristics of the prepared catalysts. The Pt,Pd,Ni/Mg0.85Zr0.15O showed the best activity in dry reforming of methane (DRM) with 99 % and 91 % for CO2 and CH4 conversions, respectively and 1.28 for H2/CO ratio at temperature 900 °C and 1:1 of CH4:CO2 ratio. The stability of Pt,Pd,Ni/Mg0.85Zr0.15O catalyst in the presence and absence of low stream 1.25 % oxygen was investigated. Carbon formation and amount in spent catalysts were examined by TEM and TGA in the presence of stream oxygen. The results showed that the amount of carbon was suppressed and negligible coke formation (less than 3 %) was observed. Several effects were observed with ZrO2 use as a promoter in the catalyst. Firstly, the magnesia cubic phase stabilized. Secondly, thermal stability and support for basicity increased. Thirdly, carbon deposition and the reducibility of Ni2+, Pd2+, and Pt2+ ions decreased. Copyright © 2018 BCREC Group. All rights reservedReceived: 25th October 2017; Revised: 2nd January 2018; Accepted: 18th January 2018; Available online: 11st June 2018; Published regularly: 1st August 2018How to Cite: Al-Doghachi, F.A.J. (2018). Effects of Platinum and Palladium Metals on Ni/Mg1-xZrxO Catalysts in the CO2 Reforming of Methane. Bulletin of Chemical Reaction Engineering & Catalysis, 13 (2): 295-310 (doi:10.9767/bcrec.13.2.1656.295-310) 

scholarly journals High Active Co/Mg1-xCex3+O Catalyst: Effects of Metal-Support Promoter Interactions on CO2 Reforming of CH4 Reaction

2021 ◽  
Vol 16 (1) ◽  
pp. 97-110
Author(s):  
Faris A. Jassim Al-Doghachi ◽  
Diyar M. A. Murad ◽  
Huda S. Al-Niaeem ◽  
Salam H. H. Al-Jaberi ◽  
Surahim Mohamad ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Fixed Bed ◽  
Fixed Bed Reactor ◽  
Dry Reforming Of Methane ◽  
Precipitation Method ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Co2 Reforming Of Ch4 ◽  
Temperature Programmed

Co/Mg1−XCe3+XO (x = 0, 0.03, 0.07, 0.15; 1 wt% cobalt each) catalysts for the dry reforming of methane (DRM) reaction were prepared using the co-precipitation method with K2CO3 as precipitant. Characterization of the catalysts was achieved by X-ray diffraction (XRD), X-ray fluorescence spectroscopy (XRF), X-ray photoelectron spectroscopy (XPS), temperature programmed reduction (H2-TPR), Brunauer–Emmett–Teller (BET), transmission electron microscopy (TEM), and thermal gravimetric analysis (TGA). The role of several reactant and catalyst concentrations, and reaction temperatures (700–900 °C) on the catalytic performance of the DRM reaction was measured in a tubular fixed-bed reactor under atmospheric pressure at various CH4/CO2 concentration ratios (1:1 to 2:1). Using X-ray diffraction, a surface area of 19.2 m2.g−1 was exhibited by the Co/Mg0.85Ce3+0.15O catalyst and MgO phase (average crystallite size of 61.4 nm) was detected on the surface of the catalyst. H2 temperature programmed reaction revealed a reduction of CoO particles to metallic Co0 phase. The catalytic stability of the Co/Mg0.85Ce3+0.15O catalyst was achieved for 200 h on-stream at 900 °C for the 1:1 CH4:CO2 ratio with an H2/CO ratio of 1.0 and a CH4, CO2 conversions of 75% and 86%, respectively. In the present study, the conversion of CH4 was improved (75%–84%) when conducting the experiment at a lower flow of oxygen (1.25%). Finally, the deposition of carbon on the spent catalysts was analyzed using TEM and Temperature programmed oxidation-mass spectroscopy (TPO-MS) following 200 h under an oxygen stream. Better anti-coking activity of the reduced catalyst was observed by both, TEM, and TPO-MS analysis. Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA   License (https://creativecommons.org/licenses/by-sa/4.0). 

scholarly journals Enhanced Photocatalytic Activity of Cu2O Cabbage/RGO Nanocomposites under Visible Light Irradiation

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1712
Author(s):  
Appusamy Muthukrishnaraj ◽  
Salma Ahmed Al-Zahrani ◽  
Ahmed Al Otaibi ◽  
Semmedu Selvaraj Kalaivani ◽  
Ayyar Manikandan ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Thermo Gravimetric Analysis ◽  
Visible Region ◽  
Catalytic Performance ◽  
Precipitation Method ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Dye Pollutants ◽  
Transmission Electron

Towards the utilization of Cu2O nanomaterial for the degradation of industrial dye pollutants such as methylene blue and methyl orange, the graphene-incorporated Cu2O nanocomposites (GCC) were developed via a precipitation method. Using Hummers method, the grapheme oxide (GO) was initially synthesized. The varying weight percentages (1–4 wt %) of GO was incorporated along with the precipitation of Cu2O catalyst. Various characterization techniques such as Fourier-transform infra-red (FT-IR), X-ray diffraction (XRD), UV–visible diffused reflectance (UV-DRS), Raman spectroscopy, thermo gravimetric analysis (TGA), energy-dispersive X-ray analysis (EDX), and electro chemical impedance (EIS) were followed for characterization. The cabbage-like morphology of the developed Cu2O and its composites were ascertained from field-emission scanning electron microscopy (FESEM) and high-resolution transmission electron microscopy (HR-TEM). In addition, the growth mechanism was also proposed. The results infer that 2 wt % GO-incorporated Cu2O composites shows the highest value of degradation efficiency (97.9% and 96.1%) for MB and MO at 160 and 220 min, respectively. Further, its catalytic performance over visible region (red shift) was also enhanced to an appreciable extent, when compared with that of other samples.

Investigations on Cu2+-substituted Ni–Zn ferrite nanoparticles

2016 ◽  
Vol 30 (32n33) ◽  
pp. 1650347
Author(s):  
Amarjeet ◽  
Vinod Kumar
Keyword(s):  
Spinel Phase ◽  
Thermo Gravimetric Analysis ◽  
Peak Position ◽  
Precipitation Method ◽  
Gravimetric Analysis ◽  
Frequency Range ◽  
X Ray Diffraction ◽  
Absorption Bands ◽  
X Ray ◽  
Zn Ferrite

[Formula: see text] ([Formula: see text] = 0.1, 0.3 and 0.5) nanoparticles were prepared by chemical co-precipitation method. The developed nanoparticles were characterized for structural properties by powder X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) techniques. Peak position in the X-ray diffraction pattern confirmed the single spinel phase of the developed particles. Infrared (IR) spectroscopy in mid-IR range showed the presence of characteristic absorption bands corresponding to octahedral and tetrahedral bonds in the spinel structure of prepared samples. Thermo-gravimetric analysis (TGA) measurements showed a considerable weight loss in the developed samples above 700[Formula: see text]C. Frequency dependence of the electrical properties of the developed material pellets was studied in the frequency range of 1 kHz–5 MHz. Temperature dependence of the dielectric constant of [Formula: see text] was studied at different temperatures, i.e. at 425, 450 and 475 K, in the frequency range of 1 kHz–5 MHz. It was found that the electrical conductivity decreases with increasing Cu[Formula: see text] ion content while it increases with the increase in temperature.

The Influence of Calcination Temperature on Quantitative Phase of Hematite from Iron Stone Tanah Laut

2015 ◽  
Vol 1112 ◽  
pp. 489-492
Author(s):  
Ali Mufid ◽  
M. Zainuri
Keyword(s):  
Particle Size ◽  
Calcination Temperature ◽  
Thermo Gravimetric Analysis ◽  
Precipitation Method ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Particle Size Analyzer ◽  
Co Precipitation

This research aims to form particles of hematite (α-Fe2O3) with a basis of mineral iron ore Fe3O4 from Tanah Laut. Magnetite Fe3O4 was synthesized using co-precipitation method. Further characterization using X-ray fluorescence (XRF) to obtain the percentage of the elements, obtained an iron content of 98.51%. Then characterized using thermo-gravimetric analysis and differential scanning calorimetry (TGA-DSC) to determine the calcination temperature, that at a temperature of 445 °C mass decreased by 0.369% due to increase in temperature. Further Characterization of X-ray diffraction (XRD) to determine the phases formed at the calcination temperature variation of 400 °C, 445 °C, 500 °C and 600 °C with a holding time of 5 hours to form a single phase α-Fe2O3 hematite. Testing with a particle size analyzer (PSA) to determine the particle size distribution, where test results indicate that the α-Fe2O3 phase of each having a particle size of 269.7 nm, 332.2 nm, 357.9 nm, 412.2 nm. The best quantity is shown at a temperature of 500 °C to form the hematite phase. This result is used as the calcination procedure to obtain a source of Fe ions in the manufacture of Lithium Ferro Phosphate.

scholarly journals Removal and Oxidation of As(III) from Water Using Iron Oxide Coated CTAB as Adsorbent

Polymers ◽  
2020 ◽  
Vol 12 (8) ◽  
pp. 1687 ◽  
Author(s):  
Daniela Predoi ◽  
Simona Liliana Iconaru ◽  
Mihai Valentin Predoi ◽  
Mikael Motelica-Heino
Keyword(s):  
Iron Oxide ◽  
Aqueous Solutions ◽  
Photoelectron Spectroscopy ◽  
Arsenic Removal ◽  
Morphological Changes ◽  
Xrd Analysis ◽  
Precipitation Method ◽  
Cubic Phase ◽  
Separation Procedure ◽  
X Ray

Iron oxides such as magnetite and maghemite coated with cetyltrimethylammonium bromide (CTAB) are very promising materials for wastewater treatment because iron oxide can be easily separated from solutions using the magnetic separation procedure Iron oxide (IO) coated CTAB was synthesized by an adapted co-precipitation method. In the present study, the IO-CTAB was used for removing arsenic from water for the first time. In the present study, the performance of iron oxide coated CTAB biocomposites as an adsorbent for arsenic removal from aqueous solutions was examined. X-ray diffraction (XRD) analysis and the results revealed a cubic phase Fd-3 m of Fe3O4 with lattice a = 8.40 Å and average crystal size equal to 17.26 ± 3 nm. The mean particle size calculated from transmission electron microscopy (TEM) was 19.86 ±1.7 nm. The results of the adsorption batch experiments and the data determined using the Langmuir and Freundlich models emphasized that IO-CTAB nanoparticles were favorable for the adsorption of As(III) ions from aqueous solutions. Ultrasound measurements have shown that IO-CTAB is a cost-effective biocomposite for removing arsenic from contaminated solutions. Moreover, x-ray photoelectron spectroscopy (XPS) has shown that during the process of arsenic absorption, there is oxidation from As(III) to As(V), which leads to a decrease in toxicity during this process. The results of the cytotoxic assays confirmed that the IO-CTAB nanoparticles did not induce any morphological changes in the HeLa cells and did not affect their proliferation after 24 h of incubation.

scholarly journals Dehydration of Fructose to 5-HMF over Acidic TiO2 Catalysts

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1178 ◽  
Author(s):  
Maria Luisa Testa ◽  
Gianmarco Miroddi ◽  
Marco Russo ◽  
Valeria La Parola ◽  
Giuseppe Marcì
Keyword(s):  
Photoelectron Spectroscopy ◽  
Thermo Gravimetric Analysis ◽  
Process Condition ◽  
Textural Properties ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
Reaction Conditions ◽  
X Ray ◽  
Catalytic Sites ◽  
Lower Temperature

Different solid sulfonic titania-based catalysts were investigated for the hydrothermal dehydration of fructose to 5-hydroxymethylfurfural (5-HMF). The catalytic behavior of the materials was evaluated in terms of fructose conversion and selectivity to 5-HMF. The surface and structural properties of the catalysts were investigated by means of X-ray diffraction (XRD), N2 adsorption isotherms, thermo-gravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS) and acid capacity measurements. Special attention was focused on the reaction conditions, both in terms of 5-HMF selectivity and the sustainability of the process, choosing water as the solvent. Among the various process condition studied, TiO2-SO3H catalyzed a complete conversion (99%) of 1.1M fructose and 5-HMF selectivity (50%) and yield (50%) at 165 °C. An important improvement of the HMF selectivity (71%) was achieved when the reaction was carried out by using a lower fructose concentration (0.1M) and lower temperature (140 °C). The catalytic activities of the materials were related to their acid capacities as much as their textural properties. In particular, a counterbalance between the acidity and the structure of the pores in which the catalytic sites are located, results in the key issue for switch the selectivity towards the achievement of 5-HMF.

scholarly journals Stoichiometric and Nonstoichiometric Compounds

2020 ◽  
Author(s):  
Paras Dubey ◽  
Netram Kaurav
Keyword(s):  
Nickel Oxide ◽  
Photoelectron Spectroscopy ◽  
Structural Phase ◽  
Thermo Gravimetric Analysis ◽  
Excess Oxygen ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Antiferromagnetic Ordering ◽  
Nonstoichiometric Compounds

This chapter gives a general overview of synthesis and recent development of nickel oxide as a nonstoichiometric compound. We establish the synthesis chemistry of nickel oxide as a nonstoichiometric material, and hence successively introduce definitions and classifications of nonstoichiometric compounds as well as their point defects. The samples of nonstoichiometric nickel oxide are synthesized by thermal decomposition method. The nonstoichiometry of samples was then studied chemically by iodometric titration, and the results are further corroborated by excess oxygen obtained from the thermo-gravimetric analysis (TGA). X-ray diffraction (XRD) and Fourier transformed infrared (FTIR) techniques are used to analyze structural phase of nonstoichiometric nickel oxide. The change in oxidation state of nickel was studied by X-ray photoelectron spectroscopy (XPS) analysis. The shift in antiferromagnetic ordering and transition temperature due to nonstoichiometry is studied by magnetic and specific heat capacity analysis.

scholarly journals Synthesis of Phosphated K-Carrageenan and Its Application for Flame-Retardant Waterborne Epoxy

Polymers ◽  
2018 ◽  
Vol 10 (11) ◽  
pp. 1268 ◽  
Author(s):  
Na Wang ◽  
Haiwei Teng ◽  
Long Li ◽  
Jing Zhang ◽  
Ping Kang
Keyword(s):  
Flame Retardant ◽  
Flame Retardancy ◽  
Photoelectron Spectroscopy ◽  
Thermo Gravimetric Analysis ◽  
Gravimetric Analysis ◽  
Mass Ratio ◽  
Thermo Gravimetric ◽  
X Ray ◽  
Cone Calorimeter Test ◽  
Waterborne Epoxy

In this paper, phosphated K-carrageenan (P-KC) was obtained by reacting POCl3 with the renewable source K-carrageenan (KC). P-KC and 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) were added into waterborne epoxy (EP) to improve its flame retardancy. The structure of P-KC was studied comprehensively using Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), thermo-gravimetric analysis (TGA), showing the successful synthesis of P-KC. The flame retardancy of the EP was evaluated by the cone calorimeter test. The results showed that different mass ratios of DOPO and P-KC affected the flame retardancy of EP. When the mass ratio of DOPO and P-KC was 2:1, total heat release (THR) and total smoke production (TSP) decreased by 48.7% and 37.4%, respectively. The microstructures of residue char were observed by FTIR and scanning electron microscopy (SEM), indicating that the flame-retardant waterborne epoxy (FR-EP) system held a more cohesive and denser char structure. The char inhibited the diffusion of heat and oxygen, which played a key role in the flame retardancy.

scholarly journals Intercalation of calcein into layered silicate magadiite and their optical properties

2017 ◽  
Vol 4 (11) ◽  
pp. 171258 ◽  
Author(s):  
Shengnan Gao ◽  
Jiang Zhu ◽  
Yifu Zhang ◽  
Qiushi Wang ◽  
Xuyang Jing ◽  
...  
Keyword(s):  
Solid State ◽  
Photoelectron Spectroscopy ◽  
Inductively Coupled Plasma ◽  
Thermo Gravimetric Analysis ◽  
Layered Silicate ◽  
Atomic Emission ◽  
Fluorescence Properties ◽  
Gravimetric Analysis ◽  
X Ray ◽  
Metal Organic

Calcein–Ca (II), Zn (II) and Al (III) complexes were successfully intercalated into interlayer surfaces of layered silicate magadiite and fluorescence properties of organic metal-chelates in the confined spaces were investigated. Structures, compositions and morphologies of the intercalated magadiites were adequately studied by tests, including X-ray diffraction, energy-dispersive X-ray spectrometer, elemental mapping, X-ray photoelectron spectroscopy, inductively coupled plasma atomic emission spectroscopy, Fourier-transform infrared spectra, ultraviolet–visible spectroscopy, thermo-gravimetric analysis, differential thermal analysis and scanning electron microscopy. Results confirmed that metal–organic chelate species were immobilized onto the silicate sheets via solid-state interaction. Basal spacings between silicate layers decreased by exchanged metal ions and increased after intercalation of calcein into the interlayer spaces of cation-exchanged magadiites. The encapsulation was obtained by a flexible solid–solid reaction, and the present reaction and products had a potential of application to industrial uses. A speculative mechanism was proposed for reaction by solid-state intercalation. Furthermore, it was found that the complexes in the interlayer space also exhibited special fluorescence properties. The significance of this current work was that it provided a possible route for synthesizing metal–organic complexes that encapsulated in phyllosilicate.

scholarly journals Improved Water–Gas Shift Performance of Au/NiAl LDHs Nanostructured Catalysts via CeO2 Addition

Nanomaterials ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 366
Author(s):  
Margarita Gabrovska ◽  
Ivan Ivanov ◽  
Dimitrinka Nikolova ◽  
Jugoslav Krstić ◽  
Anna Maria Venezia ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Nanostructured Catalysts ◽  
Water Gas Shift ◽  
Precipitation Method ◽  
Conversion Degree ◽  
Pure Hydrogen ◽  
Medium Temperature ◽  
X Ray ◽  
Supported Gold ◽  
Water Gas

Supported gold on co-precipitated nanosized NiAl layered double hydroxides (LDHs) was studied as an effective catalyst for medium-temperature water–gas shift (WGS) reaction, an industrial catalytic process traditionally applied for the reduction in the amount of CO in the synthesis gas and production of pure hydrogen. The motivation of the present study was to improve the performance of the Au/NiAl catalyst via modification by CeO2. An innovative approach for the direct deposition of ceria (1, 3 or 5 wt.%) on NiAl-LDH, based on the precipitation of Ce3+ ions with 1M NaOH, was developed. The proposed method allows us to obtain the CeO2 phase and to preserve the NiAl layered structure by avoiding the calcination treatment. The synthesis of Au-containing samples was performed through the deposition–precipitation method. The as-prepared and WGS-tested samples were characterized by X-ray powder diffraction, N2-physisorption and X-ray photoelectron spectroscopy in order to clarify the effects of Au and CeO2 loading on the structure, phase composition, textural and electronic properties and activity of the catalysts. The reduction behavior of the studied samples was evaluated by temperature-programmed reduction. The WGS performance of Au/NiAl catalysts was significantly affected by the addition of CeO2. A favorable role of ceria was revealed by comparison of CO conversion degree at 220 °C reached by 3 wt.% CeO2-modified and ceria-free Au/NiAl samples (98.8 and 83.4%, respectively). It can be stated that tuning the properties of Au/NiAl LDH via CeO2 addition offers catalysts with possibilities for practical application owing to innovative synthesis and improved WGS performance.

Sign in / Sign up

Export Citation Format

Share Document