Changes in some nutritional components of Vigna racemosa as influenced by hydrothermal processing techniques

Vigna racemosa is an underutilised hard-to-cook legume in Southwest Nigeria. The seed of V. racemosa was subjected to varying degrees of hydration levels (0%, 10%, 25%, 50% 75% and 100%) before treatment with four hydrothermal techniques, atmospheric boiling, atmospheric steaming, pressure boiling and pressure steaming. The highest percentage reduction of 65.56% in cooking time was achieved at a 100% hydration level when the seeds were processed by boiling at elevated pressure. All the hydrothermal techniques had a significant effect (p<0.05) on the protein content of the seeds. Hydration of the seeds to 100% followed by boiling at elevated pressure caused the least reduction in the protein and mineral element contents. The seed is a good source of important nutrients that are not degraded beyond the levels necessary to meet physiological needs after processing. Widening the scope of utilisation of this legume seed will make critically important nutrients such as protein more available for the teeming populations in developing countries at affordable prices, and thus, alleviating the problem of protein-energy malnutrition (PEM).

Utilizing Hydrothermal Processing to Align Structure and In Vitro Digestion Kinetics between Three Different Pulse Types

Processing results in the transformation of pulses’ structural architecture. Consequently, digestion is anticipated to emerge from the combined effect of intrinsic (matrix-dependent) and extrinsic (processed-induced) factors. In this work, we aimed to investigate the interrelated effect of intrinsic and extrinsic factors on pulses’ structural architecture and resulting digestive consequences. Three commercially relevant pulses (chickpea, pea, black bean) were selected based on reported differences in macronutrient and cell wall composition. Starch and protein digestion kinetics of hydrothermally processed whole pulses were assessed along with microstructural and physicochemical characteristics and compared to the digestion behavior of individual cotyledon cells isolated thereof. Despite different rates of hardness decay upon hydrothermal processing, the pulses reached similar residual hardness values (40 N). Aligning the pulses at the level of this macrostructural property translated into similar microstructural characteristics after mechanical disintegration (isolated cotyledon cells) with comparable yields of cotyledon cells for all pulses (41–62%). We observed that processing to equivalent microstructural properties resulted in similar starch and protein digestion kinetics, regardless of the pulse type and (prolonged) processing times. This demonstrated the capacity of (residual) hardness as a food structuring parameter in pulses. Furthermore, we illustrated that the digestive behavior of isolated cotyledon cells was representative of the digestion behavior of corresponding whole pulses, opening up perspectives for the incorporation of complete hydrothermally processed pulses as food ingredients.

Synthesis and Surface Coating of LiMn2O4 Nanorods for the Cathode of the Lithium-Ion Battery

MnO2 nanorods are prepared using a hydrothermal method, and used as precursors for the synthesis of LiMn2O4 nanorod-based active material for the cathode of lithium-ion batteries. The effects of additives, pressure, reactant concentration in the solution, and reaction time during the hydrothermal synthesis on the morphology of MnO2 are examined. For the synthesis of the LiMn2O4 nanorods, two synthetic methods, hydrothermal processing of the MnO2 precursor in a Li-containing solution, and the solid-state reaction of the precursor with LiOH·H2O powder are tested. The morphological and electrochemical properties of the resulting materials are then analyzed. The rate and cycle performances of the LiMn2O4 nanorods are considerably improved by a composite coating of Li-ion-conductive Li2O–2B2O3 and electrically conductive carbon. Because the conductive properties of these coating materials can be obtained with low crystallinity of them, superior coating performance is attainable with relatively low-temperature of after heating, which is advantageous in preserving the morphology of LiMn2O4 nanorods.

Process Analysis of Main Organic Compounds Dissolved in Aqueous Phase by Hydrothermal Processing of Açaí (Euterpe Oleraceae, Mart.) Seeds: Influence of Process Temperature, Biomass-to-Water Ratio, and Production Scales

This work aims to systematically investigate the influence of process temperature, biomass-to-water ratio, and production scales (laboratory and pilot) on the chemical composition of aqueous and gaseous phases and mass production of chemicals by hydrothermal processing of Açaí (Euterpe Oleraceae, Mart.) seeds. The hydrothermal carbonization was carried out at 175, 200, 225, and 250 °C at 2 °C/min and a biomass-to-water ratio of 1:10; at 250 °C at 2 °C/min and biomass-to-water ratios of 1:10, 1:15, and 1:20 in technical scale; and at 200, 225, and 250 °C at 2 °C/min and a biomass-to-water ratio of 1:10 in laboratory scale. The elemental composition (C, H, N, S) in the solid phase was determined to compute the HHV. The chemical composition of the aqueous phase was determined by GC and HPLC and the volumetric composition of the gaseous phase using an infrared gas analyzer. For the experiments in the pilot test scale with a constant biomass-to-water ratio of 1:10, the yields of solid, liquid, and gaseous phases varied between 53.39 and 37.01% (wt.), 46.61 and 59.19% (wt.), and 0.00 and 3.80% (wt.), respectively. The yield of solids shows a smooth exponential decay with temperature, while that of liquid and gaseous phases showed a smooth growth. By varying the biomass-to-water ratios, the yields of solid, liquid, and gaseous reaction products varied between 53.39 and 32.09% (wt.), 46.61 and 67.28% (wt.), and 0.00 and 0.634% (wt.), respectively. The yield of solids decreased exponentially with increasing water-to-biomass ratio, and that of the liquid phase increased in a sigmoid fashion. For a constant biomass-to-water ratio, the concentrations of furfural and HMF decreased drastically with increasing temperature, reaching a minimum at 250 °C, while that of phenols increased. In addition, the concentrations of CH3COOH and total carboxylic acids increased, reaching a maximum concentration at 250 °C. For constant process temperature, the concentrations of aromatics varied smoothly with temperature. The concentrations of furfural, HMF, and catechol decreased with temperature, while that of phenols increased. The concentrations of CH3COOH and total carboxylic acids decreased exponentially with temperature. Finally, for the experiments with varying water-to-biomass ratios, the productions of chemicals (furfural, HMF, phenols, cathecol, and acetic acid) in the aqueous phase is highly dependent on the biomass-to-water ratio. For the experiments at the laboratory scale with a constant biomass-to-water ratio of 1:10, the yields of solids ranged between 55.9 and 51.1% (wt.), showing not only a linear decay with temperature but also a lower degradation grade. The chemical composition of main organic compounds (furfural, HMF, phenols, catechol, and acetic acid) dissolved in the aqueous phase in laboratory-scale study showed the same behavior as those obtained in the pilot-scale study.