A Novel Graphite-Based Sorbent for Oil Spill Cleanup

The performance of an innovative material based on expanded graphite, Grafysorber® G+ (Directa Plus), has been tested through laboratory, tank, and confinement tests for oil removal in case of an oil spill and water treatment. In addition to the ability to retain oil, the possibility of reusing this material after regeneration via squeezing was also evaluated. As a comparison, the same experimental tests were conducted using polypropylene flakes (PP), the material currently most used to deal with spill accidents. Oils with different chemical and physical properties were used, namely kerosene, diesel, and crude oil. From the laboratory tests, the capacity of Grafysorber® G+ to retain oil was found to be directly proportional to the viscosity of the latter, with adsorption values ranging from 76.8 g/g for diesel to 50.8 g/g for kerosene, confirming the potential of the innovative material compared to the PP. Cyclical use tests have confirmed certain reusability of the material, even if its adsorbent capacity decreases significantly after the first cycle and continues to decrease in subsequent cycles, but a less marked manner. Finally, some considerations based on the adsorption capacities were found to suggest that the adoption of the new material is also economically preferable, resulting in savings of 20 to 40% per kg of hydrocarbon treated.

Uses of Nanoclays and Adsorbents for Dye Recovery: A Textile Industry Review

Wastewater recovery is one of the most pressing contaminant-related subjects in the textile industry. Many cleaning and recovery techniques have been applied in recent decades, from physical separation to chemical separation. This work reviews textile wastewater recovery by focusing on natural or synthetic nanoclays in order to compare their capabilities. Presently, a wide variety of nanoclays are available that can adsorb substances dissolved in water. This review summarizes and describes nanoclay modifications for different structures (laminar, tubular, etc.) to compare adsorption performance under the best conditions. This adsorbent capacity can be used in contaminant industries to recover water that can be used and be recontaminated during a second use to close the production circle. It explores and proposes future perspectives for the nanoclay hybrid compounds generated after certain cleaning steps. This is a critical review of works that have studied adsorption or desorption procedures for different nanoclay structures. Finally, it makes a future application proposal by taking into account the summarized pros and cons of each nanoclay. This work addresses contaminant reuse, where part of the employed dyes can be reused in printing or even dyeing processes, depending on the fixing capacity of the dye in the nanoclay, which is herein discussed.

Application of Agricultural Waste for the Adsorption of Pharmaceutical Pollutants in Wastewater: A Review

Modernization and growth in population have contributed to the continuous release of new and emerging chemical compounds (such as pharmaceuticals) into water sources. The importance of pharmaceuticals can never be overemphasized due to their great potential and effectiveness in the body system. However, improper management of their effluents which eventually ends up in the water in our environment has always been an issue of great concern. This led to the need for the purification of the contaminated water (wastewater). Over time, many methods of wastewater purification have been employed in the treatment of the wastewater, but yet, adsorption has been found and established to be an optimum option for the task due to its effectiveness, availability, affordability, and durability. Adsorption is a separation technique that takes place on the surface of a material or through a component called an adsorbent, and the effectiveness of this method is a function of the adsorbent capacity, contact time, temperature, and other related parameters. For adsorbent preparation, many materials have been considered and proven to be active and effective. However, in this paper, synthesizing agricultural wastes as the adsorbent in the adsorption of pharmaceutical effluents is reviewed with references, to further attest to its prominence in adsorption.

Optimization of Congo red dye adsorption from wastewater by a modified commercial zeolite catalyst using response surface modeling approach

In the present work, Zeolite A was modified by using hexadecyltrimethylammonium bromide (HDTMABr) for adsorption of the Congo red (CR) dye from synthetic aqueous solutions. The Modified Zeolite A (MZA) was characterized by XRD, SEM, and FTIR. The influence of solution pH (in the 4–12 range), ionic strength (0.1–1 M), contact time (180 min), initial CR concentration (20–60 mg/L), temperature (24–36 °C), and an adsorbent dose (1–3 g m/L) on the % dye removal and adsorbent capacity were studied. A combined effect of the initial CR concentration and temperature on the CR removal % by MZA was also studied by applying response surface methodology (RSM). Experimental values were in a good agreement with those predicated by a second-order quartic model. A maximum of 99.24% dye removal and adsorbent capacity of 21.11 mg/g was achieved under the following conditions: pH = 7, initial CR concentration = 60 mg/L, temperature = 24 °C, ionic strength = 0.1 M, adsorbent dose = 3 g/L and 90 min contact time. The equilibrium data were subjected to the Langmuir, Freundlich and Temkin isotherms, with the latter providing the best fit while kinetic adsorption studies were conducted by applying three models. The results indicated that the removal process was best described by the pseudo-second-order model. The present study demonstrates that modified MZA can be utilized for the highly efficient CR dye removal.

Fabrication of Green Diatomite/Chitosan-Based Hybrid Foams with Dye Sorption Capacity

The latest tendency of the scientific community regards the development of different classes of green materials able to solve pollution problems caused by industrial and human activity. In this paper, chitosan and diatomite were used to produce a broad-spectrum hybrid adsorbent, either in powder or in monolithic form for environmental pollutant removal. Diatomite–chitosan-based powders and porous diatomite–chitosan hybrids were prepared and characterized by chemical-physical, thermal and morphological analysis. Moreover, their adsorbent capacity towards anionic dye (Indigo Carmine) was also evaluated. Obtained data showed that chitosan improves the adsorption capacity of both systems, increasing the uptake of dye in both diatomite–chitosan systems.

Using Activated Diatomite as Adsorbent for Treatment of Arsenic Contaminated Water

Diatomite or diatomaceous earth (DE) is one of materials which can be used as an adsorbent to treat heavy metal ions from waste water, even there are many factories used it to clean the water for drinking. However, natural DE (raw DE) has very low adsorption capacity because of low specific surface area. In this work, natural DE from Lam Dong province, Viet Nam was demagnetized to remove iron and activated by HCl solution for 90 minutes with concentration of 10% at room condition. Adsorbent capacity was evaluated using As solution and the results show that the activated diatomite has adsorption capacity three times higher than that of raw DE, and the specific surface area of activated diatomite was increased 47.5% with the main chemical composition of 90.8% SiO2 and high porosity