Elastic Bottom Effects on Ocean Water Wave Scattering by a Composite Caisson-Type Breakwater Placed Upon a Rock Foundation in a Two-Layer Fluid

The association of oblique surface gravity waves with a caisson-type multi-chamber porous breakwater fitted with a perforated front wall in a two-layer fluid is studied in finite ocean depth with an elastic bottom. This study focuses on the influence of porous parameters of the interface-piercing structure on wave attenuation in surface and interfacial modes. The flexural gravity wave motion establishes the influence of the elastic bottom. The reflection coefficients for waves in both modes are evaluated to show their effects on the free surface and interface elevations and the waveloads. Consequently, the appropriateness of various configurations of the structure on the wave scattering is studied. Due to wave dissipation by the structure, less waveload is detected on the stiff wall and less elevation is noticed in the porous zone. The structure’s multi-chamber division allows it to have more dissipative and reflective properties. Adjustment of the structure’s height, breadth, and porous parameter leads to achieving good amount of wave reflection and maximum energy dissipation. An optimal width can be determined for a suitable configuration of the structure so that a breakwater can be built with an acceptable level of reflection and dissipation characteristics. The shear force and bottom deflection show how elastic parameters of the sea-floor affect wave scattering.

Numerical investigation of transient mixed convection of nanofluid in a cavity with non-Darcy porous inner block and rotating cylinders with harmonic motion

Mixed convection of nanofluid in a 2D square enclosure with a porous block in its center and four rotating cylinders, which are forced by a simple harmonic function, was studied numerically. The porous zone was studied by considering the Forchheimer–Brinkman-extended Darcy model. Effects of various parameters including Darcy number (10–5 ≤ Da ≤ 10–2), porosity (0.2 ≤ ɛ ≤ 0.7), Richardson number (0.1 ≤ Ri ≤ 10), and volume fraction of nanoparticles (0 ≤ ϕ ≤ 0.03), on heat transfer, entropy generation, PEC, velocity, streamline and isotherm contours were demonstrated. The results show that decreasing the Darcy number as well as reducing the Richardson number leads to an increase in the average Nusselt number. However, porosity changes had no decisive effect on heat transfer. Maximize the volume fraction of copper nanoparticles in the base fluid enhanced heat transfer. In the case of the high permeability of the porous medium, the impact of the harmonic rotation of the cylinders on the flow patterns became more pronounced.

Investigation of transportation of nanofluid within non-equilibrium porous media

In this investigation, numerical modeling for the behavior of nanomaterial inside a porous zone with imposing Lorentz force has been illustrated. The working fluid is a mixture of H2O and CuO and due to concentration of 0.04, it is reasonable to use the homogeneous model. Two-temperature model for porous zone was employed in which new scalar for calculating temperature of solid region was defined. CVFEM has been applied to model this complex physics. Radiation terms were considered and their influence on Nu has also been considered. Verification with benchmark proves greater accuracy. Dispersing nanopowders helps the fluid to increase velocity and reduce the temperature of inner wall. Rise of Ra results in three strong eddies inside the zone which creates two thermal plumes and it reduces the temperature of square surface about 68%. With rise of Nhs, the power of counter-clockwise vortex reduces about 61.6% and inner wall becomes warmer about 33.3%. Raising the Ha makes thermal plume to vanish and cooling rate decreases about 46.6%. Augment of Nhs makes Nu to reduce about 5.08% while augment of Ra makes it to augment about 35.64%. Also, augmenting Ha makes Nu to decline about 56.45%.

Non-Newtonian fluid flow having fluid–particle interaction through a porous zone in a channel with permeable walls

The flow of Casson fluid streaming through a porous zone in a permeable channel with homogeneously distributed dust particles is studied. The flow is oscillatory and exposed to thermal radiation. With non-uniform temperature and velocity slip at the wall, the channel is put under transverse magnetic flux control. The variable separation approach is used to obtain the exact analytic solution for the flow fields of fluid and dust particles. Physical insights of collective effects of suction/injection, magnetic field, thermal radiation, and buoyance force on the fluid velocity, temperature, rate of heat transport and friction at the wall surface are examined and analysed graphically. Results reveal that surface friction increases on both channel plates as an injection on the hot plate rises.

Comparison of Two-Phase Porosity Models for High Capacity Random Packing

High capacity random packing is used in absorption applications where a large throughput of gas is required while simultaneously maintaining as low a pressure loss as possible. Utilising computational fluid dynamics to capture the internal flow patterns and transients when designing packed bed towers can be advantageous in respect to expected performance and cost optimisation. However, capturing the direct interaction between gas, liquid and packing is not computationally feasible and therefore the packed bed is modelled as a porous media. In this work four different porosity model are calibrated with idealised equations to data for the high capacity packing IMTP or I-Ring. The different models are evaluated based on their ability to predict pressure loss and liquid holdup in the packed bed. An Eulerian two-phase model with a porous zone representing the packed bed is setup in a cylindrical tower. The CFD results are compared to the predictions of the best performing porosity model. It was found that the best performing model had an absolute mean error of 6.7% when calibrated with the idealised equations. This error increased to 10.5% when the porosity model was implemented into the CFD model.

Control of Separation Zone Behind a Flat Plate Under the Ground Effect Using Porous Lamination, Mathematical Modeling

Examination of the flat and curved plates flying close to the ground is an appropriate approach in understanding the complexity of flow behavior near a solid or liquid surface. When a body flies close to a surface, the vortex structure behind the body is changed; therefore, the resultant lift force is more than zero. This phenomenon is named “ground effect”. In this study, flat and curved plates submerged in the ground boundary layer were numerically investigated under the ground effect. After validating the desired numerical code, the influences of adding porous layer to the plates with [Formula: see text] attack angle were examined on vortex structure and flow separation behind the plate under the ground effect. The obtained results revealed that using a porous zone significantly reduced the separation zone and changed the vortex shedding structure downstream of the plates.

Numerical Simulation of Detonation Propagation in Flame Arrestor Applications

A detail numerical study of detonation propagation and interaction with a flame arrestor product was conducted. The simulation domain was based on the detonation flame arrestor validation test setup. The flame arrestor element was modeled as a porous zone using the Forchheimer equation. The coefficients of the Forchheimer equation were determined using experimental data. The Forchheimer equation was incorporated into the governing equations for axisymmetric reactive turbulent flow as a momentum sink. A 21-step elementary reaction mechanism with 10 species was used to model the stoichiometric oxyhydrogen detonation. Different cases of detonation propagation including inviscid, viscous adiabatic, and viscous with heat transfer and a porous zone were studied. A detail discussion of the detonation propagation and effect of the arrestor geometry, the heat transfer and the porous zone are presented. The inviscid numerical model solutions of the detonation propagation parameters are compared to one-dimensional analytical solution for verification. The viscous solutions are qualitatively compared to historical experimental data which shows very similar trend. The effect of the porous media parameters on shock transmission and re-initiation of detonation is presented.

Annulus shape tank with convective flow in a porous zone with impose of MHD

Current investigation deals with influence of inclusion of nanoparticles within the permeable medium within a tank with circular outer wall. The inner surface is hot and the radiative term has been imposed in temperature equation. Vorticity formula helps us to remove the pressure terms from equations and CVFEM was incorporated to calculate the amount of scalars in each node. With correlating the current data from previous paper, verification procedure was done which demonstrates good accuracy. Permeability has crucial role and greater values of Da results in stronger thermal penetration and isotherms become more disturbed. Intensity of cell augments with rise of Da about 70% in absence of Ha. Impose of Rd cannot affect the isotherms too much while it can change the Nu regarding the definition of this factor. When [Formula: see text], growth of Ha can decline the strength of eddy about 35%. Given [Formula: see text], as Da increases, Nu enhances about 10.24% and 0.25% when [Formula: see text]e5 and 1e3, respectively. Replacing platelet with sphere shape can augment the Nu about 0.38% and 0.6% when [Formula: see text] and 0, respectively.

Influence of Wind Buffers on the Aero-Thermal Performance of Skygardens

Many high-rise buildings have semi-enclosed landscaped spaces, which act as design elements to improve the social and environmental aspects of the building. Designs such as skygardens are open to outdoor airflow and allow occupants to observe the city skyline from a height. Due to their often high location, they are subjected to strong wind speeds and extreme environmental conditions. The current study investigates the effects of three common wind buffers (railing, hedges, and trees) located at a height of 92 m on the performance of a skygarden, in terms of occupants’ wind comfort. Computational fluid dynamics (CFD) simulations were carried out using the realisable k-epsilon method, where the vegetation was modelled as a porous zone with cooling capacity. The computational modelling of the high-rise building and vegetation were validated using previous works. The quality class (QC) of the Lawson comfort criteria was used for the evaluation of the wind comfort across the skygarden. The results indicate that, although the three wind buffers offer varying levels of wind reduction in the skygarden, the overall wind conditions generated are suitable for occupancy. Furthermore, vegetation is also able to offer slight temperature reductions in its wake. The right combination and dimension of these elements can greatly assist in generating aero-thermal comfort across skygardens.