Electrical Conductivity Enhancement and Electronic Applications of 2D Ti 3 C 2 T x MXene Materials

2021 ◽  
pp. 2100903
Author(s):  
Chunyang Qiao ◽  
Han Wu ◽  
Xiyan Xu ◽  
Zhengxin Guan ◽  
Wei Ou‐Yang
2019 ◽  
Author(s):  
Patricia Scheurle ◽  
Andre Mähringer ◽  
Andreas Jakowetz ◽  
Pouya Hosseini ◽  
Alexander Richter ◽  
...  

Recently, a small group of metal-organic frameworks (MOFs) has been discovered featuring substantial charge transport properties and electrical conductivity, hence promising to broaden the scope of potential MOF applications in fields such as batteries, fuel cells and supercapacitors. In combination with light emission, electroactive MOFs are intriguing candidates for chemical sensing and optoelectronic applications. Here, we incorporated anthracene-based building blocks into the MOF-74 topology with five different divalent metal ions, that is, Zn2+, Mg2+, Ni2+, Co2+ and Mn2+, resulting in a series of highly crystalline MOFs, coined ANMOF-74(M). This series of MOFs features substantial photoluminescence, with ANMOF-74(Zn) emitting across the whole visible spectrum. The materials moreover combine this photoluminescence with high surface areas and electrical conductivity. Compared to the original MOF-74 materials constructed from 2,5-dihydroxy terephthalic acid and the same metal ions Zn2+, Mg2+, Ni2+, Co2+ and Mn2+, we observed a conductivity enhancement of up to six orders of magnitude. Our results point towards the importance of building block design and the careful choice of the embedded MOF topology for obtaining materials with desired properties such as photoluminescence and electrical conductivity.


Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 1975
Author(s):  
Hyeok Jo Jeong ◽  
Hong Jang ◽  
Taemin Kim ◽  
Taeshik Earmme ◽  
Felix Sunjoo Kim

We investigate the sigmoidal concentration dependence of electrical conductivity of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) processed with linear glycol-based additives such as ethylene glycol (EG), diethylene glycol (DEG), triethylene glycol (TEG), hexaethylene glycol (HEG), and ethylene glycol monomethyl ether (EGME). We observe that a sharp transition of conductivity occurs at the additive concentration of ~0.6 wt.%. EG, DEG, and TEG are effective in conductivity enhancement, showing the saturation conductivities of 271.8, 325.4, and 326.2 S/cm, respectively. Optical transmittance and photoelectron spectroscopic features are rather invariant when the glycols are used as an additive. Two different figures of merit, calculated from both sheet resistance and optical transmittance to describe the performance of the transparent electrodes, indicate that both DEG and TEG are two most effective additives among the series in fabrication of transparent electrodes based on PEDOT:PSS films with a thickness of ~50–60 nm.


2017 ◽  
Vol 110 (12) ◽  
pp. 121904 ◽  
Author(s):  
Pietro Cataldi ◽  
Luca Ceseracciu ◽  
Sergio Marras ◽  
Athanassia Athanassiou ◽  
Ilker S. Bayer

2017 ◽  
Vol 37 (2) ◽  
pp. 163-168 ◽  
Author(s):  
Suhana Mohd Said ◽  
Shahriar Mufid Rahman ◽  
Bui Duc Long ◽  
Subramanian Balamurugan ◽  
Norhayati Soin ◽  
...  

Abstract In this work, the posttreatment of an organic polymer is performed using an inorganic acid, nitric acid (HNO3). We picked poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) as the base material and improved its electrical conductivity by acid treatment with different concentrations of HNO3. The acid treatment was able to achieve the optimum electrical conductivity of 197 S/cm, which is 115.5 times higher than the base material when treated with an aqueous solution containing 65% of HNO3. Moreover, the films showed higher transparency in the visible range while conducting Fourier transform infrared analysis. In addition, the treated films showed improved stability against outdoor operating conditions in terms of sheet resistance compared with untreated PEDOT:PSS films. We tried to develop a hypothesis to describe the reason behind the electrical conductivity enhancement by studying the thicknesses of all the samples at different acid concentration levels. The results from atomic force microscopy, the Hall effect, and the trend of film thickness suggest that the conformational change, the removal of excess PSS from the polymer, and the increase in carrier concentration are the reasons behind the improvement in electrical conductivity.


MRS Advances ◽  
2019 ◽  
Vol 4 (43) ◽  
pp. 2337-2344
Author(s):  
Adrian Goodwin ◽  
Ajit D. Kelkar ◽  
Ram V. Mohan

ABSTRACTConductive composites are being considered for use in applications such as electromagnetic shielding. Prior work has shown correlation of electrical conductivity to the microstructure of corresponding composite. In the present paper, composites consisting of polyurethane acrylic and dispersed nickel nanoparticles were fabricated, and tested for their electrical conductivity. In the fabrication process, half of the suspensions were agitated by sonication and half were not. Correlations between electrical conductivity and composite microstructural details are presented. These correlations show an optimum concentration of nickel nanoparticles that result in maximum conductivity enhancement. In addition, sonicating the suspensions increased conductivity of resulting nanocomposites. Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDS) images were used to estimate surface concentration and distribution of Nickel nanoparticles, and were correlated to electrical conductivity measurements. Parameters such as number of particles in contact and junction distance between the nano particles in the composites are suggested as a way of enhancing electrical conductivity.


Sign in / Sign up

Export Citation Format

Share Document