Influence of cold deformation on the behavior of helium in steel OKh16N15M3B

1984 ◽  
Vol 56 (5) ◽  
pp. 304-306
Author(s):  
A. G. Zaluzhnyi ◽  
M. V. Cherednichenko-Alchevskii ◽  
O. M. Storozhuk ◽  
V. F. Reutov ◽  
G. T. Zhdan
Keyword(s):  
Cold Deformation ◽  
Steel Okh16n15m3b

scholarly journals Al, Cu and Zr Addition to High Entropy Alloys: The Effect on Recrystallization Temperature

2018 ◽  
Vol 941 ◽  
pp. 1137-1142
Author(s):  
Elena Colombini ◽  
Andrea Garzoni ◽  
Roberto Giovanardi ◽  
Paolo Veronesi ◽  
Angelo Casagrande
Keyword(s):  
Solid Solution ◽  
Grain Size ◽  
Single Phase ◽  
Boundary Energy ◽  
Cold Deformation ◽  
Recrystallization Temperature ◽  
High Entropy Alloys ◽  
High Entropy ◽  
Ni Alloy ◽  
Sluggish Diffusion

The equimolar Cr, Mn, Fe, Co and Ni alloy, first produced in 2004, was unexpectedly found to be single-phase. Consequently, a new concept of materials was developed: high entropy alloys (HEA) forming a single solid-solution with a near equiatomic composition of the constituting elements. In this study, an equimolar CoCrFeMnNi HEA was modified by the addition of 5 at% of either Al, Cu or Zr. The cold-rolled alloys were annealed for 30 minutes at high temperature to investigate the recrystallization kinetics. The evolution of the grain boundary and the grain size were investigated, from the as-cast to the recrystallized state. Results show that the recrystallized single phase FCC structures exhibits different twin grains density, grain size and recrystallization temperatures as a function of the at.% of modifier alloying elements added. In comparison to the equimolar CoCrFeMnNi, the addition of modifier elements increases significantly the recrystallization temperature after cold deformation. The sluggish diffusion (typical of HEA alloys), the presence of a solute in solid solution as well as the low twin boundary energy are responsible for the lower driving force for recrystallization.

On the possibility of formation of domains with {110}〈001〉 orientation during cold deformation of commercial Fe-3% Si alloy

2006 ◽  
Vol 101 (6) ◽  
pp. 600-606 ◽  
Author(s):  
G. M. Rusakov ◽  
A. A. Redikul’tsev ◽  
M. L. Lobanov ◽  
A. I. Gomzikov
Keyword(s):  
Cold Deformation

scholarly journals Formation of microstructure and properties of Cu-3Ti alloy in thermal and thermomechanical processes

2017 ◽  
Vol 62 (1) ◽  
pp. 223-230 ◽  
Author(s):  
A. Szkliniarz
Keyword(s):  
Mechanical Properties ◽  
Electrical Conductivity ◽  
Plastic Deformation ◽  
Cold Working ◽  
Cold Deformation ◽  
Solution Treatment ◽  
Cold Plastic Deformation ◽  
Working Solution ◽  
Thermomechanical Processes ◽  
Selection Of

Abstract This paper presents the possibilities of forming the microstructure as well as mechanical properties and electrical conductivity of Cu-3Ti alloy (wt.%) in thermal and thermomechanical processes that are a combination of homogenising treatment, hot and cold working, solution treatment and ageing. Phase composition of the alloy following various stages of processing it into the specified semi-finished product was being determined too. It was demonstrated that the application of cold plastic deformation between solution treatment and ageing could significantly enhance the effect of hardening of the Cu-3Ti alloy without deteriorating its electrical conductivity. It was found that for the investigated alloy the selection of appropriate conditions for homogenising treatment, hot and cold deformation as well as solution treatment and ageing enables to obtain the properties comparable to those of beryllium bronzes.

scholarly journals Texture Evolution and Control of 2524 Aluminum Alloy and Its Effect on Fatigue Crack Propagation Behavior

2021 ◽  
Vol 11 (12) ◽  
pp. 5550
Author(s):  
Yuqiang Chen ◽  
Chuang Xiong ◽  
Wenhui Liu ◽  
Suping Pan ◽  
Yufeng Song ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Aluminum Alloy ◽  
Fatigue Crack ◽  
Cold Rolling ◽  
Texture Evolution ◽  
Cold Deformation ◽  
Solution Treatment ◽  
Second Phase ◽  
Fatigue Crack Growth Resistance ◽  
Volume Fractions

The influences of cold rolling and subsequent heat treatment on the microstructure evolution of 2524 alloy were investigated using an orientation distribution function (ODF) and electron back-scattered diffraction (EBSD). A preparation method of 2524-T3 aluminum alloy with a strong Brass texture was developed, and its effect on the fatigue properties of the alloy was investigated using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results show that with the increase in cold rolling deformation from 0% to 80%, the volume fractions of Brass, copper, and S textures in the 2524-T3 alloy also increase, especially in the case of Brass and S textures. However, the volume fractions of cube and Goss textures are reduced significantly, especially for cube textures, which are decreased by 57.4%. Reducing coarse second-phase particles (CSPs) is conducive to the formation of a strong deformation texture during cold rolling. A 10% deformation at each rolling pass, followed by a step annealing, helps the preservation of a Brass texture even after solution treatment at 500 °C for 0.5 h, while a large cold deformation followed by high-temperature annealing helps the formation of a strong cube texture. The Brass texture can enhance the strength while decreasing the fatigue crack growth resistance of this alloy.

Experimental Results of Pressing and Cold Deformation for the Development of New Pipe Products

2020 ◽  
Vol 50 (12) ◽  
pp. 902-905
Author(s):  
Ya. I. Kosmatskii ◽  
B. V. Barichko ◽  
K. Yu. Yakovleva ◽  
N. V. Fokin ◽  
V. D. Nikolenko
Keyword(s):  
Cold Deformation ◽  
Experimental Results

Influence of Strip Cooling Rate on Lüders Bands Appearance During Subsequent Cold Deformation

2019 ◽  
pp. 115-121
Author(s):  
Rešković Stoja ◽  
Brlić Tin ◽  
Jandrlić Ivan ◽  
Vodopivec Franc
Keyword(s):  
Cooling Rate ◽  
Cold Deformation ◽  
Lüders Bands

scholarly journals The Contact Mechanics of Novikov’s Surface-Hardened Gearing during Running-in Process

2018 ◽  
Vol 2018 ◽  
pp. 1-8 ◽  
Author(s):  
Alexey Beskopylny ◽  
Nikolay Onishkov ◽  
Viktor Korotkin
Keyword(s):  
Cold Deformation ◽  
Contact Fatigue ◽  
High Hardness ◽  
Contact Spot ◽  
The State ◽  
Contact Strength ◽  
Friction Forces ◽  
Contact Surfaces ◽  
Defective Surface ◽  
The Impact

The article is devoted to the analysis of the state of the contact surfaces of the higher kinematic pair in the general case of relative motion, that is, in the presence of rolling, sliding, and twisting, which is characteristic of Novikov’s circular-screw gears. The purpose of the work is to assess the impact of friction forces, the state of contact surfaces after tool processing, and the localization of the instantaneous contact spot on the level of contact—fatigue durability of gears. Power contact in the presence of geometric slippage of the mating surfaces leads to a significant change in the initial geometry and the mechanical properties of surface layers. In the existing methods of calculations of contact strength, the effect of running-in is investigated insufficiently, which leads to an incorrect result, especially for gear with high hardness of the teeth. In this work, the conditions of contact interaction close to the real requirements are studied on the basis of experimental material, numerical solution of the contact problem, determination of the terms of the contact areas of slip, and adhesion within the instantaneous spot. The shape of the instant contact spot has asymmetry and can be approximated by an ellipse with the introduction of a correction factor. The running-in period is of a plastic nature with cold deformation and reduction of the roughness of surfaces. As a result of the run-in period, the area of actual contact (tooth height) is increased by 2 or more times. It is not desirable to spread the area of contact at the area of adhesion that initiates the formation of pitting. The presence of defective surface area on the level of contact strength does not have significant influence, because of the running-in period, but increases the risk of spalling and brittle fracture.

Effect of Cold Deformation and Annealing on Microstructure and Mechanical Properties of 5083 Aluminum Alloy Sheets

2018 ◽  
Vol 913 ◽  
pp. 49-54
Author(s):  
Jian Xin Wu ◽  
Chong Gao ◽  
Rui Yin Huang ◽  
Zhen Shan Liu ◽  
Pi Zhi Zhao
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Tensile Strength ◽  
Aluminum Alloy ◽  
Annealing Temperature ◽  
Cold Deformation ◽  
Rolling Process ◽  
Prolonged Annealing ◽  
5083 Aluminum Alloy ◽  
Research Hotspots

5083 aluminum alloy, due to moderate strength, good thermal conductivity and formability, is an ideal structural material for car production. Influence of cold rolling process on microstructures and mechanical properties of 5083 aluminum alloys is significant and research hotspots. In this paper, cold deformation and annealing processes on grains, tensile properties and anisotropies of 5083 alloy sheets were studied. Results showed that incomplete recrystallization occured on 5083 alloy sheets when annealing temperature was at 300°C. The degree of recrystallization increased slightly with the cold deformation raised from 30% to 50% and varied slightly with prolonged annealing time from 2h to 4h. Furthermore, fully recrystallization occurred on 5083 alloy sheets at the annealing temperature above 320°C. Tensile strength of 5083 alloy sheets reduced significantly when the annealing temperature was raised from 300°C to 320°C, while it varied slightly when the annealing temperature continued to rise to 380°C.

High Strength Conductors and Structural Materials for High Field Magnets

MRS Advances ◽  
2016 ◽  
Vol 1 (17) ◽  
pp. 1233-1239 ◽  
Author(s):  
Ke Han ◽  
Rongmei Niu ◽  
Jun Lu ◽  
Vince Toplosky
Keyword(s):  
Service Life ◽  
High Field ◽  
Lattice Distortion ◽  
Mechanical Load ◽  
Cold Deformation ◽  
High Strength ◽  
Structural Support ◽  
Metal Metal ◽  
Lattice Distortions ◽  
Materials Used

ABSTRACTOne important approach to increasing High magnetic fields (HMF) beyond what is now possible is to improve the properties of various composite materials used as both conductors and structural support. Typical conductors for high field magnets are Cu-based metal-metal composites. To achieve high mechanical strength, these composites are fabricated by cold deformation, which introduces high densities of interfaces along with lattice distortions. During the operation of a magnet, mechanical load, high magnetic field, extreme temperatures and other stressors are imposed on the materials, causing them to be further “processed”. The composite conductors in a magnet, for example, may undergo high temperatures, which reduce lattice distortions or soften the material. At the same time, HMF may increase lattice distortion, leading to a complex change in interface characteristics. Both the mechanical properties of the conductors, like the tensile and yield strength, and the electric conductivity of the composites are closely connected to changes in lattice distortion and interface density. Understanding these changes helps us to assure that materials can operate in optimized conditions during most of magnets’ service life. Maximizing service life is critical, given the high cost of building and operating high field magnets. The goal of this paper is to 1) show our understanding of changes that occur in the properties of selected materials during the fabrication and under HMF and 2) to discuss how those changes relate to the microstructure of these materials and consequently to the service life of high field magnets.

Sign in / Sign up

Export Citation Format

Share Document