Effect of Tool Geometry and Heat Input on the Hardness, Grain Structure, and Crystallographic Texture of Thick-Section Friction Stir-Welded Aluminium

2018 ◽  
Vol 50 (1) ◽  
pp. 271-284 ◽  
Author(s):  
M. M. Z. Ahmed ◽  
B. P. Wynne ◽  
W. M. Rainforth ◽  
Adrian Addison ◽  
J. P. Martin ◽  
...  
Keyword(s):  
Crystallographic Texture ◽  
Heat Input ◽  
Grain Structure ◽  
Tool Geometry ◽  
Thick Section ◽  
Friction Stir

scholarly journals Microstructural and Process Parameters of aluminium alloys Using FSW

2021 ◽  
Vol 23 (12) ◽  
pp. 491-510
Author(s):  
Nuzhat Nazir ◽  
◽  
Manish Kumar Gupta ◽  
Keyword(s):  
Process Parameters ◽  
Aluminium Alloys ◽  
Optimal Combination ◽  
Grain Structure ◽  
Weld Strength ◽  
Tool Geometry ◽  
Relevant Parameter ◽  
Influence Of Process Parameters ◽  
Friction Stir ◽  
Fine Grain

Friction stir welding (FSW) has become a popular method for connecting low weight metals. Material joining occurs in the solid state in FSW. Inserting a rotating tool travelling over the faying surfaces of the material to be bonded is used to complete the procedure. It produces practically defect-free welds with little distortion and a fine grain structure. However, the welding mechanism and process parametric combination for welds with consistent and dependable outcomes are not well understood. The thesis details the experimental efforts made to suggest an optimal combination of parameters with simple tool geometry for FSW at greater linear speeds. The materials for research were two precipitation hardenable aluminium alloys: 6mm thick 2219-T87 and 5083H321. The influence of process parameters on weld microstructural changes and defect development was also examined. The optimal combination of process parameters for the FSW of aluminium alloys was proposed, and the most relevant parameter for weld strength and quality was discovered.

Influence of Process Heat Input on Static and Dynamic Properties of Friction Stir Welded 3mm Ti6Al4V Alloy

2014 ◽  
Vol 1019 ◽  
pp. 287-293
Author(s):  
Peter Madindwa Mashinini ◽  
D.G. Hattingh ◽  
Hannalie Lombard
Keyword(s):  
Heat Input ◽  
Dynamic Properties ◽  
Travel Speed ◽  
Ti6al4v Alloy ◽  
Tool Geometry ◽  
Original Material ◽  
Friction Stir ◽  
Tool Shoulder ◽  
The Relationship ◽  
Joint Integrity

This paper presents an investigation on the influence of varying heat input during friction stir welding of Ti6Al4V alloy, with respect to static and dynamic joint integrity. Weld heat input was controlled by varying the rotational-and tool travel speed. In the absences of large defects the welded samples failed predominately in the parent plate, while percentage elongation for all welds was lower than that of the original material. To quantify the influence of joint geometry on dynamic joint integrity, the test samples were categorised into “as-welded” and “polished” conditions for ease of comparison. Welds done at medium heat input exhibited improved fatigue strength in both conditions, while crack initiation sites for the as-welded condition was predominantly from tool shoulder marks whereas the polished sample initiation sites could be mainly linked to subsurface defects in the weld nugget. The relationship between welding tool geometry, weld defects and-process parameters is also discussed in an attempt to identify interrelationships that could be linked to joint integrity.

Quantifying crystallographic texture in the probe-dominated region of thick-section friction-stir-welded aluminium

2008 ◽  
Vol 59 (5) ◽  
pp. 507-510 ◽  
Author(s):  
M.M.Z. Ahmed ◽  
B.P. Wynne ◽  
W.M. Rainforth ◽  
P.L. Threadgill
Keyword(s):  
Crystallographic Texture ◽  
Thick Section ◽  
Friction Stir

Microstructural and Mechanical Behaviour Evaluation of Mg-Al-Zn Alloy Friction Stir Welded Joint

2020 ◽  
Vol 17 (3) ◽  
pp. 8150-8159
Author(s):  
Kulwant Singh ◽  
Gurbhinder Singh ◽  
Harmeet Singh
Keyword(s):  
Heat Treatment ◽  
Friction Stir Welding ◽  
Magnesium Alloys ◽  
Mechanical Performance ◽  
Fuel Efficiency ◽  
Research Work ◽  
Grain Structure ◽  
Tensile Fracture ◽  
Friction Stir ◽  
The Impact

The weight reduction concept is most effective to reduce the emissions of greenhouse gases from vehicles, which also improves fuel efficiency. Amongst lightweight materials, magnesium alloys are attractive to the automotive sector as a structural material. Welding feasibility of magnesium alloys acts as an influential role in its usage for lightweight prospects. Friction stir welding (FSW) is an appropriate technique as compared to other welding techniques to join magnesium alloys. Field of friction stir welding is emerging in the current scenario. The friction stir welding technique has been selected to weld AZ91 magnesium alloys in the current research work. The microstructure and mechanical characteristics of the produced FSW butt joints have been investigated. Further, the influence of post welding heat treatment (at 260 °C for 1 h) on these properties has also been examined. Post welding heat treatment (PWHT) resulted in the improvement of the grain structure of weld zones which affected the mechanical performance of the joints. After heat treatment, the tensile strength and elongation of the joint increased by 12.6 % and 31.9 % respectively. It is proven that after PWHT, the microhardness of the stir zone reduced and a comparatively smoothened microhardness profile of the FSW joint obtained. No considerable variation in the location of the tensile fracture was witnessed after PWHT. The results show that the impact toughness of the weld joints further decreases after post welding heat treatment.

scholarly journals Microstructural Evolutions of 2N Grade Pure Al and 4N Grade High-Purity Al during Friction Stir Welding

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3606
Author(s):  
Tomoya Nagira ◽  
Xiaochao Liu ◽  
Kohasaku Ushioda ◽  
Hidetoshi Fujii
Keyword(s):  
Friction Stir Welding ◽  
Dynamic Recrystallization ◽  
Grain Refinement ◽  
High Purity ◽  
Cube Texture ◽  
Grain Structure ◽  
Welding Temperature ◽  
Friction Stir ◽  
Continuous Dynamic Recrystallization ◽  
Dislocation Annihilation

The grain refinement mechanisms along the material flow path in pure and high-purity Al were examined, using the marker insert and tool stop action methods, during the rapid cooling friction stir welding using liquid CO2. In pure Al subjected to a low welding temperature of 0.56Tm (Tm: melting point), the resultant microstructure consisted of a mixture of equiaxed and elongated grains, including the subgrains. Discontinuous dynamic recrystallization (DDRX), continuous dynamic recrystallization (CDRX), and geometric dynamic recrystallization are the potential mechanisms of grain refinement. Increasing the welding temperature and Al purity encouraged dynamic recovery, including dislocation annihilation and rearrangement into subgrains, leading to the acceleration of CDRX and inhibition of DDRX. Both C- and B/-type shear textures were developed in microstructures consisting of equiaxed and elongated grains. In addition, DDRX via high-angle boundary bulging resulted in the development of the 45° rotated cube texture. The B/ shear texture was strengthened for the fine microstructure, where equiaxed recrystallized grains were fully developed through CDRX. In these cases, the texture is closely related to grain structure development.

scholarly journals Influence of Tool Geometry and Process Parameters on the Properties of Friction Stir Spot Welded Multiple (AA 5754 H111) Aluminium Sheets

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1157
Author(s):  
Danka Labus Zlatanovic ◽  
Sebastian Balos ◽  
Jean Pierre Bergmann ◽  
Stefan Rasche ◽  
Milan Pecanac ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Process Parameters ◽  
Spot Welding ◽  
Minimum Energy ◽  
Tool Geometry ◽  
Friction Stir ◽  
Minimum Energy Consumption ◽  
Punch Test ◽  
Wide Range ◽  
Lap Welding

Friction stir spot welding is an emerging spot-welding technology that offers opportunities for joining a wide range of materials with minimum energy consumption. To increase productivity, the present work addresses production challenges and aims to find solutions for the lap-welding of multiple ultrathin sheets with maximum productivity. Two convex tools with different edge radii were used to weld four ultrathin sheets of AA5754-H111 alloy each with 0.3 mm thickness. To understand the influence of tool geometries and process parameters, coefficient of friction (CoF), microstructure and mechanical properties obtained with the Vickers microhardness test and the small punch test were analysed. A scanning acoustic microscope was used to assess weld quality. It was found that the increase of tool radius from 15 to 22.5 mm reduced the dwell time by a factor of three. Samples welded with a specific tool were seen to have no delamination and improved mechanical properties due to longer stirring time. The rotational speed was found to be the most influential parameter in governing the weld shape, CoF, microstructure, microhardness and weld efficiency. Low rotational speeds caused a 14.4% and 12.8% improvement in joint efficiency compared to high rotational speeds for both tools used in this investigation.

scholarly journals Microstructural Characteristics and Mechanical Properties of Friction Stir Spot Welded 2A12-T4 Aluminum Alloy

2013 ◽  
Vol 2013 ◽  
pp. 1-10 ◽  
Author(s):  
Huijie Liu ◽  
Yunqiang Zhao ◽  
Xingye Su ◽  
Lilong Yu ◽  
Juncai Hou
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Fracture Mode ◽  
Heat Input ◽  
Tensile Shear ◽  
Microstructural Characteristics ◽  
Friction Stir ◽  
Welding Heat Input ◽  
Mixed Fracture ◽  
Spot Welded

2A12-T4 aluminum alloy was friction stir spot welded, and the microstructural characteristics and mechanical properties of the joints were investigated. A softened microstructural region existed in the joint, and it consisted of stir zone (SZ), thermal mechanically affected zone (TMAZ), and heat affected zone (HAZ). The minimum hardness was located in TMAZ, and the average hardness value in SZ can be improved by appropriately increasing welding heat input. The area of complete bonding region at the interface increased with increasing welding heat input because more interface metals were mixed. In a certain range of FSSW parameters, the tensile shear failure load of the joint increased with increasing rotation speed, but it decreased with increasing plunge rate or decreasing shoulder plunging depth. Two kinds of failure modes, that is, shear fracture mode and tensile-shear mixed fracture mode, can be observed in the tensile shear tests, and the joint that failed in the tensile-shear mixed fracture mode possessed a high carrying capability.

Sign in / Sign up

Export Citation Format

Share Document