Improvement of Mechanical Strength of a Hot-Worked Twinning-Induced Plasticity Steel through an Optimum Secondary Annealing Treatment

2021 ◽  
Author(s):  
V. García-García ◽  
F. Ruiz-León ◽  
F. Reyes-Calderón ◽  
P. Garnica-González ◽  
M. L. Mondragón-Sánchez
Keyword(s):  
Mechanical Strength ◽  
Annealing Treatment ◽  
Secondary Annealing

scholarly journals Mechanical Response of Ni-Based CU5MCuC Alloy to Different Stabilization Thermal Treatments

2020 ◽  
Author(s):  
Andrea Gruttadauria ◽  
Silvia Barella ◽  
Claudia Fiocchi
Keyword(s):  
Mechanical Properties ◽  
Corrosion Resistance ◽  
Mechanical Strength ◽  
Intergranular Corrosion ◽  
Mechanical Response ◽  
Annealing Treatment ◽  
Mechanical Tests ◽  
Thermal Treatments ◽  
Stabilization Treatment ◽  
Cr System

Abstract The Ni–Fe–Cr system is the basis of a series of commercial alloys featuring chemical–physical characteristics that allow them to be used in a variety of fields where excellent resistance to aggressive environments is required. In this scenario, the CU5MCuC alloy, the foundry counterpart of Alloy 825, is proving successful in the petrochemical field thanks to its good corrosion resistance in acidic and highly oxidizing environments. Intergranular corrosion resistance, critical for this material, is ensured by the stabilization treatment that allows precipitation of Nb carbides. Strengthening of this alloy takes place only via a solid solution. Therefore, its mechanical properties depend on the solution annealing treatment: often this treatment alone does not make it possible to reach the UTS imposed by the ASTM-A494 standard. In this work, the possibility of using stabilization treatment to increase mechanical strength as well was considered. Treatments, with different combinations of time and temperature, were carried out in order to modify the material’s microstructure. After the thermal treatments, microstructural analyses, mechanical tests and (pitting and intergranular) corrosion and resistance tests were carried out to identify optimal treatment parameters in order to promote the evolution of microstructural constituents capable of improving mechanical strength without decreasing corrosion resistance. The treatment that achieves the best compromise between mechanical properties and corrosion resistance is stabilization at 970 °C for 4 h.

Morphological transformations in solution-cast Styrene-Butadiene-Styrene (SBS) triblock copolymer thin films

1995 ◽  
Vol 53 ◽  
pp. 184-185
Author(s):  
Ginam Kim ◽  
W. Marsillo ◽  
M. Libera
Keyword(s):  
Thin Films ◽  
Triblock Copolymer ◽  
Annealing Treatment ◽  
Minor Component ◽  
Solvent Evaporation ◽  
Single Crystal Substrate ◽  
Transparent Films ◽  
Crystal Substrate ◽  
Solution Cast ◽  
Morphological Transformations

The fact that block copolymers can assume a range of morphologies depending upon such variables as relative block length and molecular weight is now well known. In the case of poly(styrene)[PS]-poly(butadiene)[PB]-poly(styrene) (SBS) triblock copolymer, the morphologies range from spheres (roughly ~20% minor component), to cylinders (roughly 20%~35% minor component), to lamellae (roughly equal component fractions) Most recently, there has been increasing interest in transformations between morphologies by thermal annealing. This paper describes initial results studying the effect of solvent evaporation rate and post-casting annealing treatment on the morphology of SBS thin films.TEM specimens were prepared by solution casting electron transparent films. 50 μl of 0.1 wt% SBS (30% styrene, Mw=14,000, Scientific Polymer Products, Inc.) dissolved in toluene was deposited on a polished NaCl single crystal substrate placed in a small dish. After solvent evaporation the film was cut into small squares, floated from the salt in water, and each square was collected on a Cu grid.

The microstructure change of low-carbon electrical steels by residual aluminum

1989 ◽  
Vol 47 ◽  
pp. 286-287
Author(s):  
C.K. Hou ◽  
C.T. Hu ◽  
Sanboh Lee
Keyword(s):  
Annealing Treatment ◽  
Low Carbon ◽  
Electrical Steels ◽  
Vacuum Degassing ◽  
Spherical Inclusions ◽  
Residual Aluminum ◽  
Average Grain Size ◽  
The Matrix ◽  
Fine Size ◽  
To Come

The fully processed low-carbon electrical steels are generally fabricated through vacuum degassing to reduce the carbon level and to avoid the need for any further decarburization annealing treatment. This investigation was conducted on eighteen heats of such steels with aluminum content ranging from 0.001% to 0.011% which was believed to come from the addition of ferroalloys.The sizes of all the observed grains are less than 24 μm, and gradually decrease as the content of aluminum is increased from 0.001% to 0.007%. For steels with residual aluminum greater than 0. 007%, the average grain size becomes constant and is about 8.8 μm as shown in Fig. 1. When the aluminum is increased, the observed grains are changed from the uniformly coarse and equiaxial shape to the fine size in the region near surfaces and the elongated shape in the central region. SEM and EDAX analysis of large spherical inclusions in the matrix indicate that silicate is the majority compound when the aluminum propotion is less than 0.003%, then the content of aluminum in compound inclusion increases with that in steel.

Characterisation of planar crystal defects in Y2Fe17Cx (0.6 ≤ x ≤ 1.6) magnetic material by High Resolution Electron Microscopy

1990 ◽  
Vol 48 (4) ◽  
pp. 774-775
Author(s):  
W. Coene ◽  
F. Hakkens ◽  
T.H. Jacobs ◽  
K.H.J. Buschow
Keyword(s):  
Electron Microscopy ◽  
High Resolution ◽  
Permanent Magnets ◽  
Annealing Treatment ◽  
High Resolution Electron Microscopy ◽  
Crystal Defects ◽  
Ordered Structure ◽  
X Ray ◽  
Planar Crystal ◽  
Resolution Electron

Intermetallic compounds of the type RE2Fe17Cx (RE= rare earth element) are promising candidates for permanent magnets. In case of Y2Fe17Cx, the Curie temperature increases from 325 K for x =0 to 550 K for x = 1.6 . X ray and electron diffraction reveal a carbon - induced structural transformation in Y2Fe17Cx from the hexagonal Th2Ni17 - type (x < 0.6 ) to the rhombohedral Th2Zn17 - type ( x ≥ 0.6). Planar crystal defects introduce local sheets of different magnetic anisotropy as compared with the ordered structure, and therefore may have an important impact on the coercivivity mechanism .High resolution electron microscopy ( HREM ) on a Philips CM30 / Super Twin has been used to characterize planar crystal defects in rhombohedral Y2Fe17Cx ( x ≥ 0.6 ). The basal plane stacking sequences are imaged in the [100] - orientation, showing an ABC or ACB sequence of Y - atoms and Fe2 - dumbbells, for both coaxial twin variants, respectively . Compounds resulting from a 3 - week annealing treatment at high temperature ( Ta = 1000 - 1100°C ) contain a high density of planar defects.

TEM study of buried cobalt disilicide layers formed by ion implantation: Identification of cobalt monosilicide inclusions

1990 ◽  
Vol 48 (4) ◽  
pp. 576-577
Author(s):  
A. De Veirman ◽  
J. Van Landuyt ◽  
K.J. Reeson ◽  
R. Gwilliam ◽  
C. Jeynes ◽  
...  
Keyword(s):  
Ion Implantation ◽  
Annealing Treatment ◽  
Silicon On Insulator ◽  
High Dose ◽  
Nitrogen Flow ◽  
Cobalt Disilicide ◽  
Transmission Electron ◽  
Beam Heating ◽  
Co Concentration ◽  
Silicon On Insulator Technology

In analogy to the formation of SIMOX (Separation by IMplanted OXygen) material which is presently the most promising silicon-on-insulator technology, high-dose ion implantation of cobalt in silicon is used to synthesise buried CoSi2 layers. So far, for high-dose ion implantation of Co in Si, only formation of CoSi2 is reported. In this paper it will be shown that CoSi inclusions occur when the stoichiometric Co concentration is exceeded at the peak of the Co distribution. 350 keV Co+ ions are implanted into (001) Si wafers to doses of 2, 4 and 7×l017 per cm2. During the implantation the wafer is kept at ≈ 550°C, using beam heating. The subsequent annealing treatment was performed in a conventional nitrogen flow furnace at 1000°C for 5 to 30 minutes (FA) or in a dual graphite strip annealer where isochronal 5s anneals at temperatures between 800°C and 1200°C (RTA) were performed. The implanted samples have been studied by means of Rutherford Backscattering Spectroscopy (RBS) and cross-section Transmission Electron Microscopy (XTEM).

FORMULATION AND DEVELOPMENT OF FAST DISSOLVING TABLET OF METOCLOPRAMIDE: AN ANTI-EMETIC DRUG

2019 ◽  
Vol 8 (6) ◽  
Author(s):  
Avilash Carpenter ◽  
M.K. Gupta ◽  
Neetesh Kumar Jain ◽  
Urvashi Sharma ◽  
Rahul Sisodiya
Keyword(s):  
Mechanical Strength ◽  
Standard Procedure ◽  
Flow Property ◽  
Storage Conditions ◽  
Angle Of Repose ◽  
Dissolution Time ◽  
Disintegration Time ◽  
Powder Blend ◽  
Standard Curve ◽  
The Stability

Aim: The main of the study is to formulate and develop orally disintegrating fast dissolving tablet of Metoclopramide hydrochloride. Material & Methods: Before formulation and development of selected drug, the standard curve in buffer was prepared and absorbance at selected maxima was taken. Then two different disintegrating agents were selected and drug was mixed with disintegrating agents in different ratio. Various Preformulation parameters and evaluation of tablet i.e. disintegration time, dissolution time, friability, hardness, thickness were measured by standard procedure. Result & Discussion: The angle of repose for all the batches prepared. The values were found to be in the range of 30.46 to 36.45, which indicates good flow property for the powder blend according to the USP. The bulk density and tapped density for all the batches varied from 0.49 to 0.54 g/mL and 0.66 to 0.73, respectively. Carr’s index values were found to be in the range of 23.33 to 25.88, which is satisfactory for the powders as well as implies that the blends have good compressibility. Hausner ratio values obtained were in the range of 1.22 to 1.36, which shows a passable flow property for the powder blend based on the USP. The results for tablet thickness and height for all batches was found to range from 4.45 to 4.72 mm and 3.67 to 3.69 mm, respectively. Hardness or breaking force of tablets for all batches was found to range from 32.8 to 36.2 N. Tablet formulations must show good mechanical strength with sufficient hardness in order to handle shipping and transportation. Friability values for all the formulations were found to be in the range of 0.22 % to 0.30 %. Conclusion: Orally disintegrating tablets were compressed in order to have sufficient mechanical strength and integrity to withstand handling, shipping and transportation. The formulation was shown to have a rapid disintegration time that complied with the USP (less than one minute). The data obtained from the stability studies indicated that the orally disintegrating mini-tablets of MTH were stable under different environmental storage conditions. Keywords: Formulation & Development, Fast Dissolving Tablet, Metoclopramide, Anti-Emetic Drug, Oral Disintegrating Tablet

Plasma Enhanced Chemical Vapor Deposition of Porous Organosilicate Glass ILD Films With k ≤ 2.4.

2003 ◽  
Vol 766 ◽  
Author(s):  
Raymond N. Vrtis ◽  
Mark L. O'Neill ◽  
Jean L. Vincent ◽  
Aaron S. Lukas ◽  
Brian K. Peterson ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Chemical Vapor Deposition ◽  
Mechanical Strength ◽  
Thermal Annealing ◽  
Vapor Deposition ◽  
Chemical Vapor ◽  
Organosilicate Glass

AbstractWe report on our work to develop a process for depositing nanoporous organosilicate (OSG) films via plasma enhanced chemical vapor deposition (PECVD). This approach entails codepositing an OSG material with a plasma polymerizable hydrocarbon, followed by thermal annealing of the material to remove the porogen, leaving an OSG matrix with nano-sized voids. The dielectric constant of the final film is controlled by varying the ratio of porogen precursor to OSG precursor in the delivery gas. Because of the need to maintain the mechanical strength of the final material, diethoxymethylsilane (DEMS) is utilized as the OSG precursor. Utilizing this route we are able to deposit films with a dielectric constant of 2.55 to 2.20 and hardness of 0.7 to 0.3 GPa, respectively.

Sign in / Sign up

Export Citation Format

Share Document