TEM study of buried cobalt disilicide layers formed by ion implantation: Identification of cobalt monosilicide inclusions

1990 ◽  
Vol 48 (4) ◽  
pp. 576-577
Author(s):  
A. De Veirman ◽  
J. Van Landuyt ◽  
K.J. Reeson ◽  
R. Gwilliam ◽  
C. Jeynes ◽  
...  
Keyword(s):  
Ion Implantation ◽  
Annealing Treatment ◽  
Silicon On Insulator ◽  
High Dose ◽  
Nitrogen Flow ◽  
Cobalt Disilicide ◽  
Transmission Electron ◽  
Beam Heating ◽  
Co Concentration ◽  
Silicon On Insulator Technology

In analogy to the formation of SIMOX (Separation by IMplanted OXygen) material which is presently the most promising silicon-on-insulator technology, high-dose ion implantation of cobalt in silicon is used to synthesise buried CoSi2 layers. So far, for high-dose ion implantation of Co in Si, only formation of CoSi2 is reported. In this paper it will be shown that CoSi inclusions occur when the stoichiometric Co concentration is exceeded at the peak of the Co distribution. 350 keV Co+ ions are implanted into (001) Si wafers to doses of 2, 4 and 7×l017 per cm2. During the implantation the wafer is kept at ≈ 550°C, using beam heating. The subsequent annealing treatment was performed in a conventional nitrogen flow furnace at 1000°C for 5 to 30 minutes (FA) or in a dual graphite strip annealer where isochronal 5s anneals at temperatures between 800°C and 1200°C (RTA) were performed. The implanted samples have been studied by means of Rutherford Backscattering Spectroscopy (RBS) and cross-section Transmission Electron Microscopy (XTEM).

Microstructural Characterization of High Dose Oxygen Implanted Silicon

1986 ◽  
Vol 74 ◽  
Author(s):  
J. L. Batstone ◽  
Alice E. White ◽  
K. T. Short ◽  
J. M. Gibson ◽  
D. C. Jacobson
Keyword(s):  
Microstructural Characterization ◽  
Amorphous Structure ◽  
Silicon On Insulator ◽  
High Dose ◽  
High Resolution Imaging ◽  
Buried Oxide ◽  
Transmission Electron ◽  
Resolution Imaging ◽  
Silicon On Insulator Technology

AbstractThe microstructure of oxygen implanted silicon for use in silicon-on- insulator technology has been examined by transmission electron microscopy. A variety of buried oxide layers prepared using oxygen doses below and above that required for stoichiometric SiO2 formation have been studied. High resolution imaging in crosssection has revealed exceptionally flat Si-SiO2 interfaces, comparable to the best thermally grown Si-SiO2 interfaces. Examination of as-implanted material shows a complex interwoven crystalline/amorphous structure which evolves during high temperature (1350–1400° C) annealing into a buried oxide layer.

Analysis of Silicon-On-Insulator Structures Formed By Oxygen Ion Implantation

1985 ◽  
Vol 43 ◽  
pp. 300-301
Author(s):  
N. Lewis ◽  
E. L. Hall ◽  
A. Mogro-Campero ◽  
R. P. Love
Keyword(s):  
Ion Implantation ◽  
Single Crystal ◽  
Single Crystal Silicon ◽  
Silicon Layer ◽  
Device Fabrication ◽  
Silicon On Insulator ◽  
High Dose ◽  
Crystal Silicon ◽  
Oxygen Ion ◽  
Oxygen Ion Implantation

The formation of buried oxide structures in single crystal silicon by high-dose oxygen ion implantation has received considerable attention recently for applications in advanced electronic device fabrication. This process is performed in a vacuum, and under the proper implantation conditions results in a silicon-on-insulator (SOI) structure with a top single crystal silicon layer on an amorphous silicon dioxide layer. The top Si layer has the same orientation as the silicon substrate. The quality of the outermost portion of the Si top layer is important in device fabrication since it either can be used directly to build devices, or epitaxial Si may be grown on this layer. Therefore, careful characterization of the results of the ion implantation process is essential.

Formation of Sic, Si3N4 and SiO2 by High-Dose Ion Implantation and Laser Annealing

1980 ◽  
Vol 1 ◽  
Author(s):  
S.W. Chiang ◽  
Y.S. Liu ◽  
R.F. Reihl
Keyword(s):  
Ion Implantation ◽  
Polycrystalline Silicon ◽  
Laser Annealing ◽  
Pulsed Laser ◽  
High Dose ◽  
Pulsed Laser Annealing ◽  
Transmission Electron ◽  
A Cell ◽  
Ft Ir ◽  
Ft Ir Spectroscopy

ABSTRACTHigh-dose ion implantation (1017 ions-cm−2) of C+, N+, and O+ at 50 KeV into silicon followed by pulsed laser annealing at 1.06 μm was studied. Formation of SiC, Si3N4, and SiO2 has been observed and investigated using Transmission Electron Microscopy (TEM) and Differential Fourier-Transform Infrared (FT-IR) Spectroscopy. Furthermore, in N+-implanted and laser-annealed silicon samples, we have observed a cell-like structure which has been identified to be spheroidal polycrystalline silicon formed by the rapid laser irradiation.

scholarly journals Thermal Annealing of High Dose P Implantation in 4H-SiC

2019 ◽  
Vol 963 ◽  
pp. 399-402 ◽  
Author(s):  
Cristiano Calabretta ◽  
Massimo Zimbone ◽  
Eric G. Barbagiovanni ◽  
Simona Boninelli ◽  
Nicolò Piluso ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Raman Spectroscopy ◽  
Ion Implantation ◽  
Epitaxial Layer ◽  
Point Defects ◽  
High Dose ◽  
Double Step ◽  
Post Annealing ◽  
Transmission Electron

In this work, we have studied the crystal defectiveness and doping activation subsequent to ion implantation and post-annealing by using various techniques including photoluminescence (PL), Raman spectroscopy and transmission electron microscopy (TEM). The aim of this work was to test the effectiveness of double step annealing to reduce the density of point defects generated during the annealing of a P implanted 4H-SiC epitaxial layer. The outcome of this work evidences that neither the first 1 hour isochronal annealing at 1650 - 1700 - 1750 °C, nor the second one at 1500 °C for times between 4 hour and 14 hour were able to recover a satisfactory crystallinity of the sample and achieve dopant activations exceeding 1%.

An analysis of high temperature (1150 °C) furnace annealing of buried oxide wafers formed by ion implantation

1989 ◽  
Vol 4 (1) ◽  
pp. 167-176 ◽  
Author(s):  
S. R. Wilson ◽  
M. E. Burnham ◽  
M. Kottke ◽  
R. P. Lorigan ◽  
S. J. Krause ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Ion Implantation ◽  
Structural Changes ◽  
Relative Number ◽  
Silicon On Insulator ◽  
Precipitate Size ◽  
Buried Oxide ◽  
Annealing Conditions ◽  
Transmission Electron ◽  
Residual Damage

Silicon-on-insulator films were formed by ion implantation of oxygen and were treated with various annealing cycles at peak temperatures of 1150 °C, 1200 °C, and 1250 °C in a conventional diffusion furnace. The objective of this study was to examine the structural effects on samples with similar oxygen diffusion lengths (from 17 to 33 μm) achieved by annealing at different times and temperatures. The oxygen and silicon distributions, as well as the residual damage and precipitate size and distribution, were measured by Auger electron microscopy, Rutherford backscattering spectroscopy, and transmission electron microscopy. In agreement with previous findings, higher temperatures produced a larger and less defective, “precipitate-free” superficial Si region. The buried oxide layer thickened from 0.33 μm to a maximum of 0.43 μm as some precipitates were incorporated into the buried oxide while others adjacent to the buried oxide grew in size (up to 47 nm) and decreased in relative number. A new result of this systematic study of annealing conditions was that the peak temperature has a greater effect on the morphology and crystal quality of the superficial Si structure than does time at temperature. Structural changes for longer anneals at 1150 °C are not equivalent to shorter anneals at 1250 °C even though the diffusion length of oxygen for these treatments is the same.

Wafer Bonding of Diamond Films to Silicon for Silicon-on-Insulator Technology

2001 ◽  
Vol 686 ◽  
Author(s):  
Gleb N. Yushin ◽  
Scott D. Wolter ◽  
Alexander V. Kvit ◽  
Ramon Collazo ◽  
John T. Prater ◽  
...  
Keyword(s):  
Wafer Bonding ◽  
Diamond Films ◽  
Polycrystalline Diamond ◽  
Amorphous Layer ◽  
Silicon On Insulator ◽  
Acoustic Microscopy ◽  
Cross Sectional ◽  
Silicon Carbon ◽  
Transmission Electron ◽  
Silicon On Insulator Technology

AbstractPolycrystalline diamond films previously grown on silicon were polished to an RMS roughness of 15 nm and bonded to the silicon in a dedicated ultrahigh vacuum bonding chamber. Successful bonding under a uniaxial mechanical stress of 32 MPa was observed at temperatures as low as 950°C. Scanning acoustic microscopy indicated complete bonding at fusion temperatures above 1150°C. Cross-sectional transmission electron microscopy later revealed a 30 nm thick intermediate amorphous layer consisting of silicon, carbon and oxygen.

Defect Pair Formation by Implantation-Induced Stresses in High-Dose Oxygen Implanted Silicon-on-Insulator Material

1993 ◽  
Vol 316 ◽  
Author(s):  
J.D. Lee ◽  
J.C. Park ◽  
D. Venables ◽  
S.J. Krause ◽  
P. Roitman
Keyword(s):  
Defect Density ◽  
Silicon On Insulator ◽  
Surface Strain ◽  
High Dose ◽  
X Ray Diffraction ◽  
Near Surface ◽  
X Ray ◽  
Density Reduction ◽  
Transmission Electron ◽  
Pair Density

ABSTRACTDefect microstructure and the near-surface strain of high-dose oxygen implanted silicon-on-insulator material (SIMOX) were investigated as a function of dose, implant temperature, and annealing temperature by transmission electron microscopy and high resolution x-ray diffraction. Dislocation half loops (DHLs) begin to form by stress assisted climb at a critical stress level due to implantation-induced damage. DHLs evolve into through-thickness defect (TTD) pairs by expansion during annealing. Both DHL and TTD-pair density increase with higher implant dose and lower implant temperature. Possible methods for defect density reduction are suggested based on the results of this study.

scholarly journals Towards p-type doping of ZnO by ion implantation

2004 ◽  
Vol 829 ◽  
Author(s):  
V. A. Coleman ◽  
H. H. Tan ◽  
C. Jagadish ◽  
S. O. Kucheyev ◽  
M. R. Phillips ◽  
...  
Keyword(s):  
Ion Implantation ◽  
Damage Accumulation ◽  
High Dose ◽  
Furnace Annealing ◽  
Light Emitting ◽  
Selective Area ◽  
Transmission Electron ◽  
Microelectronics Industry ◽  
P Type ◽  
Temperature Furnace

ABSTRACTZinc oxide is a very attractive material for a range of optoelectronic devices including blue light-emitting diodes and laser diodes. Though n-type doping has been successfully achieved, p-type doing of ZnO is still a challenge that must be overcome before p-n junction devices can be realized. Ion implantation is widely used in the microelectronics industry for selective area doping and device isolation. Understanding damage accumulation and recrystallization processes is important for achieving selective area doping. In this study, As (potential p-type dopant) ion implantation and annealing studies were carried out. ZnO samples were implanted with high dose (1.4 × 1017 ions/cm2) 300 keV As ions at room temperature. Furnace annealing of samples in the range of 900°C to 1200°C was employed to achieve recrystallization of amorphous layers and electrical activation of the dopant. Rutherford backscattering/channeling spectrometry, transmission electron microscopy and cathodolumiescence spectroscopy were used to monitor damage accumulation and annihilation behavior in ZnO. Results of this study have significant implications for p-type doing of ZnO by ion implantation.

Improved Soi Films By High Dose Oxygen Implantation and Lamp Annealing

1985 ◽  
Vol 53 ◽  
Author(s):  
G. K. Celler ◽  
P. L. F. Hemment ◽  
K. W. West ◽  
J. M. Gibson
Keyword(s):  
High Speed ◽  
Ion Beam ◽  
Silicon On Insulator ◽  
High Dose ◽  
Cmos Circuits ◽  
Radiation Hardened ◽  
Silicon On Insulator Technology ◽  
Annealing Procedure ◽  
Oxygen Precipitates ◽  
Sharp Interfaces

ABSTRACTIon beam synthesis of a buried SiO2 layer is an attractive silicon-on-insulator technology for high speed CMOS circuits and radiation hardened devices. We demonstrate here a new annealing procedure at 1405°C that produces silicon films of excellent quality, essentially free of oxygen precipitates and with sharp interfaces between the Si and the SiO2.

Sign in / Sign up

Export Citation Format

Share Document