Microstructural engineering of ceramic-matrix layered composites: Effect of grain-size dispersion on single-phase ceramic strength

1999 ◽  
Vol 59 (2) ◽  
pp. 283-289 ◽  
Author(s):  
M. Lugovy ◽  
N. Orlovskaya ◽  
K. Berroth ◽  
J. Kuebler
Keyword(s):  
Grain Size ◽  
Single Phase ◽  
Ceramic Matrix ◽  
Layered Composites ◽  
Size Dispersion

A TEM study of the influence of microstructure on the superplastic behavior of a U-5.8 wt.% Nb alloy

1986 ◽  
Vol 44 ◽  
pp. 568-569
Author(s):  
G. Mackiewicz Ludtka
Keyword(s):  
Grain Size ◽  
Heating Rate ◽  
Phase Field ◽  
Single Phase ◽  
Superplastic Behavior ◽  
Two Phase ◽  
Single Phase Field

Historically, metals exhibit superplasticity only while forming in a two-phase field because a two-phase microstructure helps ensure a fine, stable grain size. In the U-5.8 Nb alloy, superplastici ty exists for up to 2 h in the single phase field (γ1) at 670°C. This is above the equilibrium monotectoid temperature of 647°C. Utilizing dilatometry, the superplastic (SP) U-5.8 Nb alloy requires superheating to 658°C to initiate the α+γ2 → γ1 transformation at a heating rate of 1.5°C/s. Hence, the U-5.8 Nb alloy exhibits an anomolous superplastic behavior.

scholarly journals Preparation of high-entropy carbides by different sintering techniques

2021 ◽  
Vol 56 (19) ◽  
pp. 11237-11247 ◽  
Author(s):  
Johannes Pötschke ◽  
Manisha Dahal ◽  
Mathias Herrmann ◽  
Anne Vornberger ◽  
Björn Matthey ◽  
...  
Keyword(s):  
Grain Size ◽  
Single Phase ◽  
X Ray Diffraction ◽  
Vacuum Sintering ◽  
X Ray ◽  
High Entropy ◽  
Mean Grain Size ◽  
The Mean ◽  
Gas Pressure Sintering ◽  
Hardness Values

AbstractDense (Hf, Ta, Nb, Ti, V)C- and (Ta, Nb, Ti, V, W)C-based high-entropy carbides (HEC) were produced by three different sintering techniques: gas pressure sintering/sinter–HIP at 1900 °C and 100 bar Ar, vacuum sintering at 2250 °C and 0.001 bar as well as SPS/FAST at 2000 °C and 60 MPa pressure. The relative density varied from 97.9 to 100%, with SPS producing 100% dense samples with both compositions. Grain size measurements showed that the substitution of Hf with W leads to an increase in the mean grain size of 5–10 times the size of the (Hf, Ta, Nb, Ti, V,)C samples. Vacuum-sintered samples showed uniform grain size distribution regardless of composition. EDS mapping revealed the formation of a solid solution with no intermetallic phases or element clustering. X-ray diffraction analysis showed the structure of mostly single-phase cubic high-entropy carbides. Hardness measurements revealed that (Hf, Ta, Nb, Ti, V)C samples possess higher hardness values than (Ta, Nb, Ti, V, W)C samples.

scholarly journals Overview of HSS Steel Grades Development and Study of Reheating Condition Effects on Austenite Grain Size Changes

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 1988
Author(s):  
Tibor Kvackaj ◽  
Jana Bidulská ◽  
Róbert Bidulský
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
High Strength Steel ◽  
Single Phase ◽  
Hsla Steel ◽  
High Strength ◽  
Strength Properties ◽  
Austenite Grain Size ◽  
Austenite Grain ◽  
Steel Grades

This review paper concerns the development of the chemical compositions and controlled processes of rolling and cooling steels to increase their mechanical properties and reduce weight and production costs. The paper analyzes the basic differences among high-strength steel (HSS), advanced high-strength steel (AHSS) and ultra-high-strength steel (UHSS) depending on differences in their final microstructural components, chemical composition, alloying elements and strengthening contributions to determine strength and mechanical properties. HSS is characterized by a final single-phase structure with reduced perlite content, while AHSS has a final structure of two-phase to multiphase. UHSS is characterized by a single-phase or multiphase structure. The yield strength of the steels have the following value intervals: HSS, 180–550 MPa; AHSS, 260–900 MPa; UHSS, 600–960 MPa. In addition to strength properties, the ductility of these steel grades is also an important parameter. AHSS steel has the best ductility, followed by HSS and UHSS. Within the HSS steel group, high-strength low-alloy (HSLA) steel represents a special subgroup characterized by the use of microalloying elements for special strength and plastic properties. An important parameter determining the strength properties of these steels is the grain-size diameter of the final structure, which depends on the processing conditions of the previous austenitic structure. The influence of reheating temperatures (TReh) and the holding time at the reheating temperature (tReh) of C–Mn–Nb–V HSLA steel was investigated in detail. Mathematical equations describing changes in the diameter of austenite grain size (dγ), depending on reheating temperature and holding time, were derived by the authors. The coordinates of the point where normal grain growth turned abnormal was determined. These coordinates for testing steel are the reheating conditions TReh = 1060 °C, tReh = 1800 s at the diameter of austenite grain size dγ = 100 μm.

scholarly journals Al, Cu and Zr Addition to High Entropy Alloys: The Effect on Recrystallization Temperature

2018 ◽  
Vol 941 ◽  
pp. 1137-1142
Author(s):  
Elena Colombini ◽  
Andrea Garzoni ◽  
Roberto Giovanardi ◽  
Paolo Veronesi ◽  
Angelo Casagrande
Keyword(s):  
Solid Solution ◽  
Grain Size ◽  
Single Phase ◽  
Boundary Energy ◽  
Cold Deformation ◽  
Recrystallization Temperature ◽  
High Entropy Alloys ◽  
High Entropy ◽  
Ni Alloy ◽  
Sluggish Diffusion

The equimolar Cr, Mn, Fe, Co and Ni alloy, first produced in 2004, was unexpectedly found to be single-phase. Consequently, a new concept of materials was developed: high entropy alloys (HEA) forming a single solid-solution with a near equiatomic composition of the constituting elements. In this study, an equimolar CoCrFeMnNi HEA was modified by the addition of 5 at% of either Al, Cu or Zr. The cold-rolled alloys were annealed for 30 minutes at high temperature to investigate the recrystallization kinetics. The evolution of the grain boundary and the grain size were investigated, from the as-cast to the recrystallized state. Results show that the recrystallized single phase FCC structures exhibits different twin grains density, grain size and recrystallization temperatures as a function of the at.% of modifier alloying elements added. In comparison to the equimolar CoCrFeMnNi, the addition of modifier elements increases significantly the recrystallization temperature after cold deformation. The sluggish diffusion (typical of HEA alloys), the presence of a solute in solid solution as well as the low twin boundary energy are responsible for the lower driving force for recrystallization.

Structure of Low Cobalt Alloy for Permanent Magnets of Basis System Fe-Cr-Co at Complex Two-Level Loading in Isothermal Conditions

2007 ◽  
Vol 539-543 ◽  
pp. 2928-2933 ◽  
Author(s):  
V.S. Yusupov ◽  
A.I. Milyaev ◽  
Galia F. Korznikova ◽  
Alexander V. Korznikov ◽  
J.K. Kovneristii
Keyword(s):  
Grain Size ◽  
Active Zone ◽  
Single Phase ◽  
Permanent Magnets ◽  
Phase Region ◽  
The Body ◽  
Coarse Grained ◽  
Isothermal Conditions ◽  
Basis System ◽  
Level Loading

Results of experimental research into evolution of the structure and microhardness of the hard magnetic Fe-30Cr-8Co-0,7Ti-0,5V-0,7Si alloy during complex two-level loading (compression + torsion) in isothermal conditions at various temperatures in single-phase region are reported. It was revealed that the deformation leads to a strong refinement of initial coarse-grained structure in the whole volume of the sample, however the generated structure is non-uniform through the body of the sample. In an active zone of deformation, near to mobile head, there is a microcrystalline layer with a grain size of about 5 microns which thickness poorly depends on the formation. With removal from the active zone of deformation the grain size increases, and microhardness decreases.

Simulation of Fabrication for Al2O3 Ceramic Tool Materials

2012 ◽  
Vol 500 ◽  
pp. 537-543 ◽  
Author(s):  
Bin Fang ◽  
Chuan Zhen Huang ◽  
Hong Tao Zhu ◽  
Chong Hai Xu
Keyword(s):  
Grain Size ◽  
Monte Carlo ◽  
Microstructure Evolution ◽  
Potts Model ◽  
Single Phase ◽  
Ceramic Tool ◽  
Tool Materials ◽  
Fabrication Parameters

The new Monte Carlo Potts model that couples with fabrication parameters and considers pores and additives has been developed in order to simulate the fabrication of single-phase ceramics tool materials. The microstructure evolution for single-phase Al2O3 ceramic tool materials is simulated with the different technology parameters. At the same time, the single-phase Al2O3 ceramic tool materials are fabricated with the corresponding technology parameters. The errors of grain size between the simulated and the experimental is 12.1 and18.2%.

scholarly journals Effect of Sintering Temperature on the Microstructure, Electrical and Magnetotransport Properties of La0.67Sr0.33MnO3 Compound

2014 ◽  
Vol 895 ◽  
pp. 319-322
Author(s):  
Lim Kean Pah ◽  
Abdul Halim Shaari ◽  
Chen Soo Kien ◽  
Chin Hui Wei ◽  
Albert Gan ◽  
...  
Keyword(s):  
Grain Size ◽  
Single Phase ◽  
Sintering Temperature ◽  
Measurement Range ◽  
Hexagonal Structure ◽  
Precipitation Method ◽  
Metal Insulator ◽  
Higher Temperature ◽  
Co Precipitation ◽  
Grain Surface

In this work, we report the effect of sintering temperature (900°C, 1000°C, 1100°C and 1200°C) on the electrical and magnetotransport properties of polycrystalline La0.67Sr0.33MnO3 (LSMO). Single phase of LSMO hexagonal structure (R-3c) accompanied with minor phases was successfully synthesized by co-precipitation method. With increasing sintering temperature, grain growth was promoted and grain connectivity was improved. It was found that an enhancement of resistivity on smaller grain size was due to larger grain surface over volume (grain boundaries effect). The shifting of the metal-insulator transition (TMI) to higher temperature was also responsible for observed changes in physical properties. TMI of 900°C, 1000°C and 1100°C were 232 K, 278 K and 298 K respectively however 1200°C was out of measurement range (higher than 300 K). In summary, CP900 with smaller grain size distribution (~200 nm) displayed the highest resistivity and MR% of -19.2% (at 80 K, 10 kG).

Preparation of Nanocrystalline Fe2O3 Powder by Cryomilling with Liquid Nitrogen and its Magnetic Property

2020 ◽  
Vol 993 ◽  
pp. 806-810
Author(s):  
Zhi Wei Zhang ◽  
Bing Wei Luo ◽  
Hai Tao Zhou ◽  
Fen Wang
Keyword(s):  
Particle Size ◽  
Grain Size ◽  
Magnetic Property ◽  
Liquid Nitrogen ◽  
Room Temperature ◽  
Single Phase ◽  
Rapid Preparation ◽  
Mean Particle Size ◽  
Milling Temperature ◽  
The Mean

Rapid preparation of nanocrystalline γ-Fe2O3 powder with superparamagnetism was realized by cryomilling commercial Fe2O3 powder using liquid nitrogen. The effects of milling temperature and duration on the grain size, phase and microstructure of the nanocrystalline Fe2O3 powder were analyzed. Magnetic property of the nanocrystalline γ-Fe2O3 powder was also tested by magnetometer at room temperature. The results demonstrate that nanocrystalline γ-Fe2O3 powder with single phase can be prepared rapidly by cryomilling with liquid nitrogen. The mean particle size of γ-Fe2O3 powder can be reduced from 300 nm to 13 nm by cryomilling at −130 °C within 3 hours. The nanocrystalline γ-Fe2O3 powder shows superparamagnetism at room temperature.

Effect of Wood Template on Magnetic Properties of Ni0.5Zn0.5Fe2-xCrxO4 Ceramics

2019 ◽  
Vol 956 ◽  
pp. 107-113
Author(s):  
Rui Li ◽  
Liang Cun Qian ◽  
Xue Feng Sun
Keyword(s):  
Grain Size ◽  
Saturation Magnetization ◽  
Spinel Structure ◽  
Single Phase ◽  
Sol Gel ◽  
Porous Ceramics ◽  
Nanocrystalline Powders ◽  
Test Results ◽  
Doping Amount ◽  
Wood Template

Porous Ni0.5Zn0.5Fe2-xCrxO4 (x = 0, 0.1, 0.2, 0.3, 0.4 and 0.5) ceramics were prepared by a sol-gel method using basswood as the mold. At the same time, Ni0.5Zn0.5Fe2-xCrxO4 nanocrystalline powders were obtained by sintering the gel in oxygen at high temperature. The result of the XRD test showed that all samples presented the single-phase of the cubic spinel structure. With the increase of doping amount x, both porous ceramics and nanopowders decreased their grain size; At the same doping amount, the grain size of powder ferrites was about twice as large as that of porous ceramics. The magnetic test results showed that with the increase of doping amount x, the coercivity values increased monotonously and the saturation magnetization values decreased monotonously for all samples. Under the same doping content, the saturation magnetization values were lower but the coercivity values were higher as compared to the powder ferrites.

Sign in / Sign up

Export Citation Format

Share Document