A Transmission Electron Microscopical Investigation of Phase Transformations in TiNi

1980 ◽  
Vol 38 ◽  
pp. 340-341
Author(s):  
P. Moine ◽  
G. M. Michal ◽  
R. Sinclair
Keyword(s):  
Electron Microscopy ◽  
Phase Transformations ◽  
Applied Stress ◽  
Structural Changes ◽  
Microscopical Investigation ◽  
Temperature Range ◽  
Transmission Electron ◽  
Electron Microscopical ◽  
Diffraction Effects ◽  
Microscopy Images

Premartensitic effects in near equiatomic TiNi have been pointed out by several authors(1-5). These include anomalous contrast in electron microscopy images (mottling, striations, etc. ),diffraction effects(diffuse streaks, extra reflections, etc.), a resistivity peak above Ms (temperature at which a perceptible amount of martensite is formed without applied stress). However the structural changes occuring in this temperature range are not well understood. The purpose of this study is to clarify these phenomena.

Embedding Procedure for Water Swollen Samples

1970 ◽  
Vol 28 ◽  
pp. 504-505
Author(s):  
Ann M. Thomas ◽  
Virginia Shemeley
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Ion Exchange ◽  
Structural Changes ◽  
Cross Linking ◽  
Ion Exchange Resins ◽  
Transmission Electron ◽  
First Pass ◽  
Exchange Resins

Those samples which swell rapidly when exposed to water are, at best, difficult to section for transmission electron microscopy. Some materials literally burst out of the embedding block with the first pass by the knife, and even the most rapid cutting cycle produces sections of limited value. Many ion exchange resins swell in water; some undergo irreversible structural changes when dried. We developed our embedding procedure to handle this type of sample, but it should be applicable to many materials that present similar sectioning difficulties.The purpose of our embedding procedure is to build up a cross-linking network throughout the sample, while it is in a water swollen state. Our procedure was suggested to us by the work of Rosenberg, where he mentioned the formation of a tridimensional structure by the polymerization of the GMA biproduct, triglycol dimethacrylate.

Ultrastructure of the soil fungus, Geomyces pannorus

1984 ◽  
Vol 42 ◽  
pp. 738-739
Author(s):  
J. A. Traquair ◽  
E. G. Kokko
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Fine Structure ◽  
Low Temperatures ◽  
Soil Fungus ◽  
Organic Soils ◽  
Anatomical Studies ◽  
Transmission Electron ◽  
Electron Microscopical ◽  
Scanning Electron

With the advent of improved dehydration techniques, scanning electron microscopy has become routine in anatomical studies of fungi. Fine structure of hyphae and spore surfaces has been illustrated for many hyphomycetes, and yet, the ultrastructure of the ubiquitous soil fungus, Geomyces pannorus (Link) Sigler & Carmichael has been neglected. This presentation shows that scanning and transmission electron microscopical data must be correlated in resolving septal structure and conidial release in G. pannorus.Although it is reported to be cellulolytic but not keratinolytic, G. pannorus is found on human skin, animals, birds, mushrooms, dung, roots, and frozen meat in addition to various organic soils. In fact, it readily adapts to growth at low temperatures.

scholarly journals Green Synthesis of Feather-Shaped MoS2/CdS Photocatalyst for Effective Hydrogen Production

2013 ◽  
Vol 2013 ◽  
pp. 1-5 ◽  
Author(s):  
Yang Liu ◽  
Hongtao Yu ◽  
Xie Quan ◽  
Shuo Chen
Keyword(s):  
Electron Microscopy ◽  
Hydrogen Production ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance ◽  
Sulfur Source ◽  
X Ray ◽  
Transmission Electron ◽  
Microscopy Images ◽  
Effective Hydrogen ◽  
Better Than

MoS2/CdS photocatalyst was fabricated by a hydrothermal method for H2production under visible light. This method used low toxic thiourea as a sulfur source and was carried out at 200°C. Thus, it was better than the traditional methods, which are based on an annealing process at relatively high temperature (above 400°C) using toxic H2S as reducing agent. Scanning electron microscopy and transmission electron microscopy images showed that the morphologies of MoS2/CdS samples were feather shaped and MoS2layer was on the surface of CdS. The X-ray photoelectron spectroscopy testified that the sample was composed of stoichiometric MoS2and CdS. The UV-vis diffuse reflectance spectra displayed that the loading of MoS2can enhance the optical absorption of MoS2/CdS. The photocatalytic activity of MoS2/CdS was evaluated by producing hydrogen. The hydrogen production rate on MoS2/CdS reached 192 μmol·h−1. This performance was stable during three repeated photocatalytic processes.

Error Quantification in Strain Mapping Methods

2007 ◽  
Vol 13 (5) ◽  
pp. 320-328 ◽  
Author(s):  
Elisa Guerrero ◽  
Pedro Galindo ◽  
Andrés Yáñez ◽  
Teresa Ben ◽  
Sergio I. Molina
Keyword(s):  
Electron Microscopy ◽  
Geometric Phase ◽  
Step Response ◽  
Strain Mapping ◽  
Error Quantification ◽  
Transmission Electron ◽  
Mapping Techniques ◽  
Microscopy Images ◽  
Real State

In this article a method for determining errors of the strain values when applying strain mapping techniques has been devised. This methodology starts with the generation of a thickness/defocus series of simulated high-resolution transmission electron microscopy images of InAsxP1−x/InP heterostructures and the application of geometric phase. To obtain optimal defocusing conditions, a comparison of different defocus values is carried out by the calculation of the strain profile standard deviations among different specimen thicknesses. Finally, based on the analogy of real state strain to a step response, a characterization of strain mapping error near an interface is proposed.

Control of Morphology and Growth Direction of Gallium Nitride Nanostructures

2003 ◽  
Vol 789 ◽  
Author(s):  
Seung Yong Bae ◽  
Hee Won Seo ◽  
Jeunghee Park
Keyword(s):  
Electron Microscopy ◽  
Gallium Nitride ◽  
Large Scale ◽  
Chemical Vapor ◽  
Growth Direction ◽  
Chemical Vapor Deposition Method ◽  
X Ray Diffraction ◽  
Oxide Mixture ◽  
Temperature Range ◽  
Transmission Electron

ABSTRACTVarious shaped single-crystalline gallium nitride (GaN) nanostructures were produced by chemical vapor deposition method in the temperature range of 900–1200 °C. Scanning electron microscopy, transmission electron microscopy, electron diffraction, x-ray diffraction, electron energy loss spectroscopy, Raman spectroscopy, and photoluminescence were used to investigate the structural and optical properties of the GaN nanostructures. We controlled the GaN nanostructures by the catalyst and temperature. The cylindrical and triangular shaped nanowires were synthesized using iron and gold nanoparticles as catalysts, respectively, in the temperature range of 900 – 1000 °C. We synthesized the nanobelts, nanosaws, and porous nanowires using gallium source/ boron oxide mixture. When the temperature of source was 1100 °C, the nanobelts having a triangle tip were grown. At the temperature higher up to 1200 °C the nanosaws and porous nanowires were formed with a large scale. The cylindrical nanowires have random growth direction, while the triangular nanowires have uniform growth direction [010]. The growth direction of the nanobelts is perpendicular to the [010]. Interestingly, the nanosaws and porous nanowires exhibit the same growth direction [011]. The shift of Raman, XRD, and PL bands from those of bulk was correlated with the strains of the GaN nanostructures.

Interfacial precipitation in titania-doped diphasic mullite gels

1998 ◽  
Vol 13 (4) ◽  
pp. 974-978 ◽  
Author(s):  
Seong-Hyeon Hong ◽  
Naesung Lee ◽  
Altaf H. Carim ◽  
Gary L. Messing
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
High Resolution ◽  
Phase Transformations ◽  
Orientation Relationship ◽  
Sol Gel ◽  
Sintered Body ◽  
Transmission Electron

Interfacial precipitation in sol-gel derived, titania-doped diphasic mullite gels was investigated using conventional and high resolution transmission electron microscopy. Rutile, anatase, and brookite precipitated on the interface between {110} planes of mullite and glass pockets in the sintered body. The formation of brookite may be attributable to the Si- and Al-rich environment during precipitation. Each polymorph of titania has a unique morphology and orientation relationship with mullite. Brookite exhibits a truncated pill box shape, and anatase displays a vermicular morphology. Quenching experiments suggest that the precipitates grow and undergo phase transformations during cooling.

scholarly journals Chemical Stability of Ti3C2 MXene with Al in the Temperature Range 500–700 °C

Materials ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 1979 ◽  
Author(s):  
Jing Zhang ◽  
Shibo Li ◽  
Shujun Hu ◽  
Yang Zhou
Keyword(s):  
Electron Microscopy ◽  
Chemical Stability ◽  
Metal Matrix ◽  
Matrix Composites ◽  
X Ray Diffraction ◽  
X Ray ◽  
Temperature Range ◽  
Transmission Electron ◽  
Work First ◽  
Scanning Electron

Ti3C2Tx MXene, a new 2D nanosheet material, is expected to be an attractive reinforcement of metal matrix composites because its surfaces are terminated with Ti and/or functional groups of –OH, –O, and –F which improve its wettability with metals. Thus, new Ti3C2Tx/Al composites with strong interfaces and novel properties are desired. To prepare such composites, the chemical stability of Ti3C2Tx with Al at high temperatures should be investigated. This work first reports on the chemical stability of Ti3C2Tx MXene with Al in the temperature range 500–700 °C. Ti3C2Tx is thermally stable with Al at temperatures below 700 °C, but it reacts with Al to form Al3Ti and TiC at temperatures above 700 °C. The chemical stability and microstructure of the Ti3C2Tx/Al samples were investigated by differential scanning calorimeter, X-ray diffraction analysis, scanning electron microscopy, and transmission electron microscopy.

Sign in / Sign up

Export Citation Format

Share Document