Concurrent dual-band SiGe HBT power amplifier for Wireless applications

2009 ◽  
Vol 1 (2) ◽  
pp. 117-126 ◽  
Author(s):  
Vittorio Camarchia ◽  
Rocco Giofrè ◽  
Iacopo Magrini ◽  
Luca Piazzon ◽  
Alessandro Cidronali ◽  
...  
Keyword(s):  
Output Power ◽  
Power Amplifier ◽  
Orthogonal Frequency Division Multiplexing ◽  
Maximum Output Power ◽  
System Level ◽  
Dual Band ◽  
Maximum Output ◽  
System Architectures ◽  
Power Added Efficiency ◽  
Mode Operation

This paper presents an investigation of a concurrent low-cost dual-band power amplifier (PA) fabricated in SiGe technology, able to simultaneously operate at two frequencies of 2.45 and 3.5-GHz, including an evaluation of its system level performance potentiality. Taking into account the technology novelty and the lack of device characterization and modeling, a hybrid (MIC) approach has been adopted both for a fast prototyping of the PA and for the evaluation of the device potentiality based on an extensive linear and nonlinear characterization. The comparison of PA performance in single-band or concurrent mode operation will be presented. In particular, the measured PA prototype shows an output power of 17.2 and 17-dBm at a 1-dB compression point, at 2.45 and 3.5-GHz, respectively, for CW single-mode operation, with a power added efficiency around 20%. System-level analysis predicts that, when the PA is operated under the 20-MHz Orthogonal Frequency-Division Multiplexing (OFDM) concurrent signals, the maximum output power levels to maintain the Error Vector Magnitude (EVM) within 5% are 11 and 3.5-dBm at 2.45 and 3.5-GHz, respectively. Moreover, new concepts and possible new system architectures for the development of the next generation of the multi-band transceiver front-end will be provided with an extensive system-level evaluation of the amplifier.

A 5.2/5.8 GHz Dual Band On-Off Keying Transmitter Design for Bio-Signal Transmission

2018 ◽  
Vol 3 (2) ◽  
Author(s):  
Chang-Hsi Wu ◽  
Hong-Cheng You ◽  
Shun-Zhao Huang
Keyword(s):  
Output Power ◽  
Power Amplifier ◽  
Power Efficiency ◽  
Supply Voltage ◽  
Maximum Output Power ◽  
Dual Band ◽  
Maximum Output ◽  
Power Combiner ◽  
Power Added Efficiency ◽  
Chip Size

Abstract An architecture of 5.2/5.8-GHz dual-band on-off keying (DBOOK) modulated transmitter is designed in a 0.18-μm CMOS technology. The proposed DBOOK transmitter is used in the biosignal transmission system with high power efficiency and small area. To reduce power consumption and enhance output swing, two pairs of center-tapped transformers are used as both LC tank and source grounding choke for the designed voltage controlled oscillator (VCO). Switching capacitances are used to achieve dual band operations, and a complemented power combiner is used to merge the differential output power of VCO to a single-ended output. Besides, the linearizer circuits are used in the proposed power amplifier with wideband output matching to improve the linearity both at 5.2/5.8-GHz bands. The designed DBOOK transmitter is implemented by dividing it into two chips. One chip implements the dual-band switching VCO and power combiner, and the other chip implements a linear power amplifier including dual-band operation. The first chip drives an output power of 2.2mW with consuming power of 5.13 mW from 1.1 V supply voltage. With the chip size including pad of 0.61 × 0.91 m2, the measured data rate and transmission efficiency attained are 100 Mb/s and 51 pJ/bit, respectively. The second chip, for power enhanced mode, exhibits P1 dB of −9 dBm, IIP3 of 1 dBm, the output power 1 dB compression point of 12.42 dBm, OIP3 of about 21 dBm, maximum output power of 17.02/16.18 dBm, and power added efficiency of 17.13/16.95% for 5.2/ 5.8 GHz. The chip size including pads is 0:693 × 1:084mm2.

A fully matched dual stage CMOS power amplifier with integrated passive linearizer attaining 23 db gain, 40% PAE and 28 DBM OIP3

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Premmilaah Gunasegaran ◽  
Jagadheswaran Rajendran ◽  
Selvakumar Mariappan ◽  
Yusman Mohd Yusof ◽  
Zulfiqar Ali Abdul Aziz ◽  
...  
Keyword(s):  
Power Consumption ◽  
Output Power ◽  
Power Amplifier ◽  
Maximum Output Power ◽  
Maximum Output ◽  
Power Gain ◽  
Matching Network ◽  
Content Type ◽  
Power Added Efficiency ◽  
Main Amplifier

Purpose The purpose of this paper is to introduce a new linearization technique known as the passive linearizer technique which does not affect the power added efficiency (PAE) while maintaining a power gain of more than 20 dB for complementary metal oxide semiconductor (CMOS) power amplifier (PA). Design/methodology/approach The linearization mechanism is executed with an aid of a passive linearizer implemented at the gate of the main amplifier to minimize the effect of Cgs capacitance through the generation of opposite phase response at the main amplifier. The inductor-less output matching network presents an almost lossless output matching network which contributes to high gain, PAE and output power. The linearity performance is improved without the penalty of power consumption, power gain and stability. Findings With this topology, the PA delivers more than 20 dB gain for the Bluetooth Low Energy (BLE) Band from 2.4 GHz to 2.5 GHz with a supply headroom of 1.8 V. At the center frequency of 2.45 GHz, the PA exhibits a gain of 23.3 dB with corresponding peak PAE of 40.11% at a maximum output power of 14.3 dBm. At a maximum linear output power of 12.7 dBm, a PAE of 37.3% has been achieved with a peak third order intermodulation product of 28.04 dBm with a power consumption of 50.58 mW. This corresponds to ACLR of – 20 dBc, thus qualifying the PA to operate for BLE operation. Practical implications The proposed technique is able to boost up the efficiency and output power, as well as linearize the PA closer to 1 dB compression point. This reduces the trade-off between linear output power and PAE in CMOS PA design. Originality/value The proposed CMOS PA can be integrated comfortably to a BLE transmitter, allowing it to reduce the transceiver’s overall power consumption.

RF-MEMS multi-mode-matching networks for GaN power transistors

2014 ◽  
Vol 6 (5) ◽  
pp. 447-458 ◽  
Author(s):  
Sascha A. Figur ◽  
Friedbert van Raay ◽  
Rüdiger Quay ◽  
Larissa Vietzorreck ◽  
Volker Ziegler
Keyword(s):  
Output Power ◽  
Power Amplifier ◽  
Rf Mems ◽  
Operation Mode ◽  
Maximum Output Power ◽  
Maximum Output ◽  
Mode Matching ◽  
Power Added Efficiency ◽  
Matching Networks ◽  
Multi Mode

This work presents radio-frequency-microelectromechanical-system (RF-MEMS)-based tunable input- and output-matching networks for a multi-band gallium nitride (GaN) power-amplifier applications. In the first part, circuit designs are shown and characterized for a fixed operation mode of the transistor, i.e. either a maximum-output-power- or a maximum-power-added-efficiency (PAE)-mode, which are finally combined into a multi-mode-matching network (M3N); the M3N allows to tune the operation mode of the transistor independently of its operational frequency. The matching networks are designed to provide optimum matching for the power amplifier at three to six different operating frequencies for maximum-output-power- and maximum-PAE-mode. In the frequency range from 3.5 to 8.5 GHz, return losses of 10 dB and higher were measured and insertion losses of 0.5–1.9 dB were demonstrated for the output-matching networks. Further characterizations were performed to test the dependency on the RF-input power, and no changes were observed up to power levels of 34 dBm when cold-switched.

DOUBLE SUPPLY, LINEAR, AND HIGH EFFICIENCY PUSH AMPLIFIER DESIGN FOR ENVELOPE TRACKING POWER AMPLIFIERS IN WiMAX APPLICATIONS

2014 ◽  
Vol 23 (08) ◽  
pp. 1450113 ◽  
Author(s):  
MOHAMMAD MOGHADDAM TABRIZI ◽  
NASSER MASOUMI
Keyword(s):  
Output Power ◽  
Power Amplifier ◽  
High Performance ◽  
High Efficiency ◽  
Maximum Output Power ◽  
Total Efficiency ◽  
Maximum Output ◽  
Error Vector Magnitude ◽  
Power Added Efficiency ◽  
Amplifier Design

In this work, a novel and efficient approach is proposed to optimize linearity and efficiency of a power amplifier used in mobile communication applications. A linear and high performance push amplifier is designed and analyzed to extract design equations for an optimum performance. The proposed push amplifier has two sections; an analog section and a switching section. The analog section provides the required linearity and the switching section guarantees the satisfaction of the total efficiency level. Double power supply scheme is used in push amplifiers to enhance its performance. Two separate power supplies are employed for linear and switching sections of push amplifiers which have different voltage levels. The implemented circuit is simulated using HSPICERF with TSMC models for active and passive elements. The proposed power amplifier (PA) provides a maximum output power of 25 dBm and power added efficiency (PAE) as high as 51% at 2.5 GHz operation frequency. At 1-dB compression point, this PA exhibits output power of 25 dBm with 48% PAE and 4.5% error vector magnitude (EVM) which is appropriate for 64QAM OFDM signals.

Design of a 0.7~2.6GHz Wideband Power Amplifier in 0.18-μm CMOS Process

2014 ◽  
Vol 618 ◽  
pp. 543-547
Author(s):  
Zhou Yu ◽  
Xiang Ning Fan ◽  
Zai Jun Hua ◽  
Chen Xu
Keyword(s):  
Output Power ◽  
Power Amplifier ◽  
Negative Feedback ◽  
Maximum Output Power ◽  
Cmos Process ◽  
Maximum Output ◽  
Power Gain ◽  
Class A ◽  
Simulation Results ◽  
Multi Mode

A power amplifier (PA) for multi-mode multi-standard transceiver which is implemented in a TSMC 0.18μm process is presented. The proposed PA uses matching compensation, lossy matching network and negative feedback technique to improve bandwidth. To achieve the linearity performance, the two-stage PA operates in Class-A regime. Simulation results show that the power amplifier achieves maximum output power of more than 24dBm in 0.7~2.6GHz. The output P1dBof the PA is larger than 22dBm. The simulated power gain is more than 27dB. The S11 is less than-10dB and the S22 is under-5dB.

scholarly journals A Novel Configuration of A Microstrip Power Amplifier based on GaAs-FET for ISM Applications

2018 ◽  
Vol 8 (5) ◽  
pp. 3882
Author(s):  
Amine Rachakh ◽  
Larbi El Abdellaoui ◽  
Jamal Zbitou ◽  
Ahmed Errkik ◽  
Abdelali Tajmouati ◽  
...  
Keyword(s):  
Output Power ◽  
Power Amplifier ◽  
Return Loss ◽  
Maximum Output Power ◽  
Maximum Power ◽  
Design System ◽  
Stability Factor ◽  
Maximum Output ◽  
Power Gain ◽  
Microstrip Technology

Power Amplifiers (PA) are very indispensable components in the design of numerous types of communication transmitters employed in microwave technology. The methodology is exemplified through the design of a 2.45GHz microwave power Amplifier (PA) for the industrial, scientific and medical (ISM) applications using microstrip technology. The main design target is to get a maximum power gain while simultaneously achieving a maximum output power through presenting the optimum impedance which is characteristically carried out per adding a matching circuit between the source and the input of the power amplifier and between the load and the output of the power amplifier. A "T" matching technique is used at the input and the output sides of transistor for assure in band desired that this circuit without reflections and to obtain a maximum power gain. The proposed power amplifier for microwave ISM applications is designed, simulated and optimized by employing Advanced Design System (ADS) software by Agilent. The PA shows good performances in terms of return loss, output power, power gain and stability; the circuit has an input return loss of -38dB and an output return loss of -33.5dB. The 1-dB compression point is 8.69dBm and power gain of the PA is 19.4dBm. The Rollet's Stability measure B1 and the stability factor K of the amplifier is greater than 0 and 1 respectively, which shows that the circuit is unconditionally stable. The total chip size of the PA is 73.5× 36 mm2.

scholarly journals Extended Bandwidth and Increased Efficiency Quasi-Doherty Power Amplifier Design With A Revised Approach For Load Modulation

2021 ◽  
Author(s):  
Seyedehmarzieh Rouhani ◽  
Kasra Rouhi ◽  
Adib Abrishamifar ◽  
Majid Tayarani
Keyword(s):  
Power Amplifier ◽  
High Power ◽  
Maximum Output Power ◽  
Input Power ◽  
Maximum Efficiency ◽  
Maximum Output ◽  
Power Added Efficiency ◽  
Active Feedback ◽  
Doherty Power Amplifier ◽  
Load Modulation

This paper presents an approach to power added efficiency (PAE) increase for Quasi-Doherty power amplifier (Q-DPA) design. For this aim, active feedback is utilized instead of a passive quarter wavelength transmission line (TL) usage, which is conventionally used in the DPA schematic. PAE increase can be done by applying an accurate load modulation to the main amplifier (PAmain), especially for technologies in which output impedance of the main power amplifier (Zout,main) considerably varies in both low and high power regions. Because such precise modulation is still based on a modified TL, this approach suffers from the inherent narrowband behavior of that TL. As a consequence, expecting a wideband DPA may not be satisfied in all cases. To deal with this issue, active feedback is used to play a role in reaching PAmain, which is not saturated before, to its maximum efficiency at the highest level of received input power (Pin) in the high power region. Following Zout,main trajectories in power and frequency sweeps simultaneously just by a passive TL are not needed anymore. Still, for the sake of preventing total PAE degradation due to the consummated power by the feedback path’s power amplifier (PAfeedback) should be limited, analytical confinement is provided in this work. A comparison is made between GaAs pHEMT 0.25um MMIC technology-based conventional DPA and the proposed revised approach based-DPA to verify the mentioned approach. The proposed PA shows maximum output power of 33.4 dBm, maximum PAE of 41.6, fractional bandwidth of 11%. The Q-DPA works with a maximum power gain of 24.16.

A High Temperature Linear Wideband Power Amplifier for a Downhole Communication System

2017 ◽  
Vol 2017 (HiTEN) ◽  
pp. 000114-000117
Author(s):  
S. Reza Hiemstra ◽  
Brannon M. Kerrigan ◽  
Dong S. Ha
Keyword(s):  
Ambient Temperature ◽  
Power Amplifier ◽  
Communication System ◽  
Oil And Gas ◽  
Maximum Output Power ◽  
Oil And Gas Industry ◽  
Junction Temperature ◽  
Maximum Output ◽  
Gas Industry ◽  
Power Added Efficiency

Abstract In order to reach previously untapped wells, the oil and gas industry continues to drill deeper, resulting in extreme operating temperatures for electronic systems. It is essential for electronic circuits and systems to be able to withstand extreme temperatures. The proposed power amplifier (PA) intends for a downhole communication system operating at an ambient temperature of 230 °C. The proposed PA is designed with Qorvo T2G6003028-FL GaN on SiC HEMT, which offers a high junction temperature. The proposed PA can operate reliably up to an ambient temperature of 230 °C with the operation frequency from 228 MHz to 263 MHz. At 230 °C, it achieves maximum output power of 1.66 W, the peak gain of 24 dB, peak PAE (power added efficiency) of 25%, OP1dB (output 1-db compression point) of 32 dBm, and OIP3 (output third intercept point) of 37.9 dBm..

scholarly journals Increased Efficiency of a Current Compensating Load Modulation Based MMIC Doherty Power Amplifier Design In 0.25m GaAs pHEMT Technology

2020 ◽  
Author(s):  
Seyedehmarzieh Rouhani ◽  
Kasra Rouhi ◽  
Adib Abrishamifar ◽  
Majid Tayarani
Keyword(s):  
Power Amplifier ◽  
Second Harmonic ◽  
Maximum Output Power ◽  
Input Power ◽  
Maximum Output ◽  
Modulation Equation ◽  
Gain Compression ◽  
Power Added Efficiency ◽  
Doherty Power Amplifier ◽  
Load Modulation

In this work, a premise is applied to the conventional load modulation equation of Doherty power amplifier (DPA) in 0.25 m GaAs pHEMT technology to compensate output impedance of main amplifier ( Z out,main ) variation, even in low power region. Using this modified modulation leads to the DPAs power added efficiency (PAE) increase in comparison by the case in which the load modulation revision is ignored, which is also designed in this paper. Second harmonic rejection networks are also added to both designs to play their roles as to efficiency increase. By doing so, the revised load modulation based DPA has the maximum PAE of 39.6%, maximum output power ( P out ) of 31.61dBm, at 8 GHz. Simulation results of this DPA in higher harmonics indicate the designed DPA has the minimum second and third harmonics power of -51.7 dBm and -80 dBm, respectively. For the sake of linearity evaluation, it is depicted that 1dB-power gain compression has not occurred in the input power (P in ) range in which the proposed DPA works.

Sign in / Sign up

Export Citation Format

Share Document