Design and modeling of an ultra-wideband low-noise distributed amplifier in InP DHBT technology

2019 ◽  
Vol 11 (7) ◽  
pp. 635-644 ◽  
Author(s):  
T. Shivan ◽  
E. Kaule ◽  
M. Hossain ◽  
R. Doerner ◽  
T. Johansen ◽  
...  
Keyword(s):  
Noise Figure ◽  
Impedance Matching ◽  
Low Noise ◽  
Ultra Wideband ◽  
Frequency Range ◽  
Collector Current ◽  
Noise Sources ◽  
Distributed Amplifier ◽  
Double Heterojunction ◽  
High Bandwidth

AbstractThis paper reports on an ultra-wideband low-noise distributed amplifier (LNDA) in a transferred-substrate InP double heterojunction bipolar transistor (DHBT) technology which exhibits a uniform low-noise characteristic over a large frequency range. To obtain very high bandwidth, a distributed architecture has been chosen with cascode unit gain cells. Each unit cell consists of two cascode-connected transistors with 500 nm emitter length and ft/fmax of ~360/492 GHz, respectively. Due to optimum line-impedance matching, low common-base transistor capacitance, and low collector-current operation, the circuit exhibits a low-noise figure (NF) over a broad frequency range. A 3-dB bandwidth from 40 to 185 GHz is measured, with an NF of 8 dB within the frequency range between 75 and 105 GHz. Moreover, this circuit demonstrates the widest 3-dB bandwidth operation among all reported single-stage amplifiers with a cascode configuration. Additionally, this work has proposed that the noise sources of the InP DHBTs are largely uncorrelated. As a result, a reliable prediction can be done for the NF of ultra-wideband circuits beyond the frequency range of the measurement equipment.

A 3–14 GHz, Self-Body Biased Common-Gate UWB LNA for Wireless Applications in 90 nm CMOS

2019 ◽  
Vol 28 (04) ◽  
pp. 1950056 ◽  
Author(s):  
Vikram Singh ◽  
Sandeep Kumar Arya ◽  
Manoj Kumar
Keyword(s):  
Reflection Coefficient ◽  
Noise Figure ◽  
Impedance Matching ◽  
Low Noise ◽  
Ultra Wideband ◽  
Common Source ◽  
Cmos Process ◽  
Frequency Range ◽  
Continuous Growth ◽  
Common Gate

Inspired from continuous growth in the field of low power and low noise wireless communication devices, a low noise amplifier (LNA) using self-body biased common-gate (CG) configuration is presented in this paper. The proposed LNA is designed for 3–14[Formula: see text]GHz ultra-wideband (UWB) frequency range using 90[Formula: see text]nm CMOS process. Common-gate configuration with self-body biasing has been used at the input stage to provide wideband input matching with low noise figure (NF) for the complete UWB frequency. An impedance matching network consisting of parallel to series RLC network has been used between common-gate and cascaded common source (CS) stages. Two stages of the CS configuration have been used for bandwidth enhancement and to increase the power gain (S[Formula: see text]) with acceptable NF. Buffer stage at the output has been used to achieve output reflection coefficient (S[Formula: see text]) less than [Formula: see text]10.8[Formula: see text]dB. The proposed LNA achieves an average S[Formula: see text] of 15.9[Formula: see text][Formula: see text][Formula: see text]0.7[Formula: see text]dB with a maximum of 16.7[Formula: see text]dB at 3.0[Formula: see text]GHz and NF of 1.68–2.7[Formula: see text]dB for 3.1–10.6[Formula: see text]GHz UWB frequency range. It provides input reflection coefficient (S[Formula: see text]) less than [Formula: see text]10.2[Formula: see text]dB, reverse isolation (S[Formula: see text]) less than [Formula: see text]75.8[Formula: see text]dB and a NF of 1.68–4.0[Formula: see text]dB throughout the proposed UWB frequency range. The proposed LNA provides input 1[Formula: see text]dB compression point (P1dB) of [Formula: see text]13[Formula: see text]dBm and input third-order intercept point (IIP3) of [Formula: see text]8[Formula: see text]dBm at 6[Formula: see text]GHz. It consumes 20.1[Formula: see text]mW of power from a 1.2[Formula: see text]V power supply.

scholarly journals Design and Performance Investigation of a New Distributed Amplifier Architecture for 40 and 100 Gb/s Optical Receivers

2015 ◽  
Vol 14 (5) ◽  
pp. 5661-5686
Author(s):  
Essra E. Al-Bayati ◽  
R. S. Fyath
Keyword(s):  
Communication Systems ◽  
Noise Figure ◽  
Complementary Metal Oxide Semiconductor ◽  
Low Noise ◽  
Ultra Wideband ◽  
Oxide Semiconductor ◽  
Cmos Process ◽  
Optical Receivers ◽  
Distributed Amplifier ◽  
Design Scheme

The design of distributed amplifiers (DAs) is one of the challenging aspects in emerging ultra high bit rate optical communication systems. This is especially important when implementation in submicron silicon complementary metal oxide semiconductor (CMOS) process is considered. This work presents a novel design scheme for DAs suitable for frontend amplification in 40 and 100 Gb/s optical receivers. The goal is to achieve high flat gain and low noise figure (NF) over the ultra wideband operating bandwidth (BW). The design scheme combines shifted second tire (SST) matrix configuration with cascode amplification cell configuration and uses m-derived technique. Performance investigation of the proposed DA architecture is carried out and the results are compared with that of other DA architectures reported in the literature. The investigation covers the gain and NF spectra when the DAs are implemented in 180, 130, 90, 65 and 45 CMOS standards.The simulation results reveal that the proposed DA architecture offers the highest gain with highest degree of flatness and low NF when compared with other DA configurations. Gain-BW products of 42772 and 21137 GHz are achieved when the amplifier is designed for 40 and 100 Gb/s operation, respectively, using 45 nm CMOS standard. Thesimulation is performed using AWR Microwave Office (version 10).

scholarly journals Low Noise Amplifier with Improved Gain and Reduced Noise-Figure in 90nm CMOS Technology

2021 ◽  
pp. 85-94
Author(s):  
Dr. Rashmi S B ◽  
Mr. Raghavendra B ◽  
Mr. Sanketh V
Keyword(s):  
Reflection Coefficient ◽  
Noise Figure ◽  
Cmos Technology ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Ultra Wideband ◽  
Common Source ◽  
Frequency Range ◽  
Common Gate ◽  
Noise Amplifier

A CMOS low noise amplifier (LNA) for ultra-wideband (UWB) wireless applications is presented in this paper. The proposed CMOS low noise amplifier (LNA) is designed using common-gate (CG) topology as the first stage to achieve ultra-wideband input matching. The common-gate (CG) is cascaded with common- source (CS) topology with current-reused configuration to enhance the gain and noise figure (NF) performance of the LNA with low power. The Buffer stage is used as output matching network to improve the reflection coefficient. The proposed low noise amplifier (LNA) is implemented using CADENCE Virtuoso Analog and Digital Design Environment tool in 90nm CMOS technology. The LNA provides a forward voltage gain or power gain (S21) of 32.34dB , a minimum noise figure of 2dB, a reverse-isolation (S12) of less than - 38.74dB and an output reflection coefficient (S22) of less than -7.4dB for the entire ultra-wideband frequency range. The proposed LNA has an input reflection coefficient (S11) of less than -10dB for the ultra-wideband frequency range. It achieves input referred 1-dB compression point of 78.53dBm and input referred 3-dB compression point of 13dBm. It consumes only 24.226mW of power from a Vdd supply of 0.7V.

60 GHz-Band Low-Noise Amplifier

2017 ◽  
Vol 26 (05) ◽  
pp. 1750075 ◽  
Author(s):  
Najam Muhammad Amin ◽  
Lianfeng Shen ◽  
Zhi-Gong Wang ◽  
Muhammad Ovais Akhter ◽  
Muhammad Tariq Afridi
Keyword(s):  
Transmission Line ◽  
Quality Factor ◽  
Noise Figure ◽  
Cmos Technology ◽  
Low Noise ◽  
Constant Current ◽  
60 Ghz ◽  
Frequency Range ◽  
Constant Current Density ◽  
Chip Area

This paper presents the design of a 60[Formula: see text]GHz-band LNA intended for the 63.72–65.88[Formula: see text]GHz frequency range (channel-4 of the 60[Formula: see text]GHz band). The LNA is designed in a 65-nm CMOS technology and the design methodology is based on a constant-current-density biasing scheme. Prior to designing the LNA, a detailed investigation into the transistor and passives performances at millimeter-wave (MMW) frequencies is carried out. It is shown that biasing the transistors for an optimum noise figure performance does not degrade their power gain significantly. Furthermore, three potential inductive transmission line candidates, based on coplanar waveguide (CPW) and microstrip line (MSL) structures, have been considered to realize the MMW interconnects. Electromagnetic (EM) simulations have been performed to design and compare the performances of these inductive lines. It is shown that the inductive quality factor of a CPW-based inductive transmission line ([Formula: see text] is more than 3.4 times higher than its MSL counterpart @ 65[Formula: see text]GHz. A CPW structure, with an optimized ground-equalizing metal strip density to achieve the highest inductive quality factor, is therefore a preferred choice for the design of MMW interconnects, compared to an MSL. The LNA achieves a measured forward gain of [Formula: see text][Formula: see text]dB with good input and output impedance matching of better than [Formula: see text][Formula: see text]dB in the desired frequency range. Covering a chip area of 1256[Formula: see text][Formula: see text]m[Formula: see text]m including the pads, the LNA dissipates a power of only 16.2[Formula: see text]mW.

scholarly journals A 1.5–40 GHz frequency modulated continuous wave radar receiver front-end

2021 ◽  
pp. 1-11
Author(s):  
Mantas Sakalas ◽  
Niko Joram ◽  
Frank Ellinger
Keyword(s):  
Continuous Wave ◽  
Noise Figure ◽  
Supply Voltage ◽  
Low Noise ◽  
Ultra Wideband ◽  
Front End ◽  
Wave Radar ◽  
Bicmos Technology ◽  
Circuit Components ◽  
High Band

Abstract This study presents an ultra-wideband receiver front-end, designed for a reconfigurable frequency modulated continuous wave radar in a 130 nm SiGe BiCMOS technology. A variety of innovative circuit components and design techniques were employed to achieve the ultra-wide bandwidth, low noise figure (NF), good linearity, and circuit ruggedness to high input power levels. The designed front-end is capable of achieving 1.5–40 GHz bandwidth, 30 dB conversion gain, a double sideband NF of 6–10.7 dB, input return loss better than 7.5 dB and an input referred 1 dB compression point of −23 dBm. The front-end withstands continuous wave power levels of at least 25 and 20 dBm at low band and high band inputs respectively. At 3 V supply voltage, the DC power consumption amounts to 302 mW when the low band is active and 352 mW for the high band case, whereas the total IC size is $3.08\, {\rm nm{^2}}$ .

scholarly journals A 0.18um CMOS Low Noise Amplifier for 3-5ghz UWB Receivers

2018 ◽  
Vol 7 (3.6) ◽  
pp. 84
Author(s):  
N Malika Begum ◽  
W Yasmeen
Keyword(s):  
Power Supply ◽  
Noise Figure ◽  
Cmos Technology ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Ultra Wideband ◽  
Noise Amplifier ◽  
5 Ghz ◽  
Chebyshev Filter ◽  
Minimum Noise

This paper presents an Ultra-Wideband (UWB) 3-5 GHz Low Noise Amplifier (LNA) employing Chebyshev filter. The LNA has been designed using Cadence 0.18um CMOS technology. Proposed LNA achieves a minimum noise figure of 2.2dB, power gain of 9dB.The power consumption is 6.3mW from 1.8V power supply.  

scholarly journals CMOS Ultra-Wideband Low Noise Amplifier Design

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
K. Yousef ◽  
H. Jia ◽  
R. Pokharel ◽  
A. Allam ◽  
M. Ragab ◽  
...  
Keyword(s):  
Impedance Matching ◽  
Cmos Technology ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Ultra Wideband ◽  
Output Impedance ◽  
Integrated Inductor ◽  
Technology Process ◽  
Amplifier Design ◽  
Noise Amplifier

This paper presents the design of ultra-wideband low noise amplifier (UWB LNA). The proposed UWB LNA whose bandwidth extends from 2.5 GHz to 16 GHz is designed using a symmetric 3D RF integrated inductor. This UWB LNA has a gain of 11 ± 1.0 dB and a NF less than 3.3 dB. Good input and output impedance matching and good isolation are achieved over the operating frequency band. The proposed UWB LNA is driven from a 1.8 V supply. The UWB LNA is designed and simulated in standard TSMC 0.18 µm CMOS technology process.

scholarly journals A 1 to 32 GHz broadband multi-octave receiver for monolithic integrated vector network analyzers in SiGe technology

2018 ◽  
Vol 10 (5-6) ◽  
pp. 717-728
Author(s):  
Marco Dietz ◽  
Andreas Bauch ◽  
Klaus Aufinger ◽  
Robert Weigel ◽  
Amelie Hagelauer
Keyword(s):  
Noise Figure ◽  
Gain Control ◽  
Wide Frequency Range ◽  
Low Noise ◽  
Vector Network Analyzer ◽  
Ultra Wideband ◽  
Network Analyzer ◽  
Active Mixer ◽  
Input Matching ◽  
Better Than

AbstractA multi-octave receiver chain is presented for the use in a monolithic integrated vector network analyzer. The receiver exhibits a very wide frequency range of 1–32 GHz, where the gain meets the 3 dB-criterion. The differential receiver consists of an ultra-wideband low noise amplifier, an active mixer and an output buffer and exhibits a maximum conversion gain (CG) of 16.6 dB. The main design goal is a very flat CG over five octaves, which eases calibration of the monolithic integrated vector network analyzer. To realize variable gain functionality, without losing much input matching, an extended gain control circuit with additional feedback branch is shown. For the maximum gain level, a matching better than −10 dB is achieved between 1–28 GHz, and up to 30.5 GHz the matching is better than −8.4 dB. For both, the input matching and the gain of the LNA, the influence of the fabrication tolerances are investigated. A second gain control is implemented to improve isolation. The measured isolations between RF-to-LO and LO-to-RF are better than 30 dB and 60 dB, respectively. The LO-to-IF isolation is better than 35 dB. The noise figure of the broadband receiver is between 4.6 and 5.8 dB for 4–32 GHz and the output referred 1-dB-compression-point varies from 0.1 to 4.3 dBm from 2–32 GHz. The receiver draws a current of max. 66 mA at 3.3 V.

ON-CHIP INDUCTORS OPTIMIZATION FOR ULTRA WIDE BAND LOW NOISE AMPLIFIERS

2011 ◽  
Vol 20 (07) ◽  
pp. 1231-1242 ◽  
Author(s):  
J. DEL PINO ◽  
SUNIL L. KHEMCHANDANI ◽  
ROBERTO DÍAZ-ORTEGA ◽  
R. PULIDO ◽  
H. GARCÍA-VÁZQUEZ
Keyword(s):  
Quality Factor ◽  
Noise Figure ◽  
Impedance Matching ◽  
Broad Band ◽  
Wide Band ◽  
Design Guidelines ◽  
Low Noise ◽  
Low Noise Amplifiers ◽  
Integrated Inductor ◽  
On Chip

In this work, the influence of the inductor quality factor in wide band low noise amplifiers has been studied. Electromagnetic simulations have been used to model the integrated inductor broad band response. The influence of the quality factor on LNA performance of the inductors that compound the impedance matching networks, inductive degeneration and broadband load has been studied, obtaining design guidelines for optimizing the amplifier gain flatness. Using this guidelines, an LNA with wideband input matching, shunt-peaking load, and an output buffer was designed. Using Austria Mikro Systems BiCMOS 0.35 m process, a prototype has been fabricated achieving the following measured specifications: maximum gain of 12.5 dB at 3.4 GHz with a -3 dB bandwidth of 1.7–5.3 GHz, noise figure from 4.3 to 5.2 dB, and unity gain at 9.4 GHz.

Design of Low-Noise Two-Path Amplifier for 6–16 GHz Applications

2020 ◽  
pp. 2150136
Author(s):  
Asieh Parhizkar Tarighat ◽  
Mostafa Yargholi
Keyword(s):  
Noise Figure ◽  
Impedance Matching ◽  
High Gain ◽  
Low Noise ◽  
Cmos Process ◽  
Input Matching ◽  
Inductive Peaking ◽  
Linearity Improvement ◽  
Noise Amplifier ◽  
Path Structure

A two-path low-noise amplifier (LNA) is designed with TSMC 0.18[Formula: see text][Formula: see text]m standard RF CMOS process for 6–16[Formula: see text]GHz frequency band applications. The principle of a conventional resistive shunt feedback LNA is analyzed to demonstrate the trade-off between the noise figure (NF) and the input matching. To alleviate the mentioned issue for wideband application, this structure with noise canceling technique and linearity improvement are applied to a two-path structure. Flat and high gain is supplied by the primary path; while the input and output impedance matching are provided by the secondary path. The [Formula: see text][Formula: see text]dB bandwidth can be increased to a higher frequency by inductive peaking, which is used at the first stage of the two paths. Besides, by biasing the transistors at the threshold voltage, low power dissipation is achieved. The [Formula: see text][Formula: see text]dB gain bandwidth of the proposed LNA is 10[Formula: see text]GHz, while the maximum power gain of 13.1[Formula: see text]dB is attained. With this structure, minimum NF of 4.6[Formula: see text]dB and noise flatness of 1[Formula: see text]dB in the whole bandwidth can be achieved. The input impedance is matched, and S[Formula: see text] is lower than [Formula: see text]10 dB. With the proposed linearized LNA, the average IIP[Formula: see text][Formula: see text]dBm is gained, while it occupies 1051.7[Formula: see text][Formula: see text]m die area.

Sign in / Sign up

Export Citation Format

Share Document