scholarly journals Characterization of Limestone as Raw Material to Hydrated Lime

2018 ◽  
Vol 34 ◽  
pp. 02042 ◽  
Author(s):  
Rajeb Salem Hwidi ◽  
Tengku Nuraiti Tengku Izhar ◽  
Farah Naemah Mohd Saad
Keyword(s):  
Raw Materials ◽  
Hydrated Lime ◽  
Raw Material ◽  
Morphological Properties ◽  
X Ray Diffraction ◽  
Absorption Bands ◽  
X Ray ◽  
Main Chemical Composition ◽  
The Difference

In Malaysia, limestone is essentially important for the economic growth as raw materials in the industry sector. Nevertheless, a little attention was paid to the physical, chemical, mineralogical, and morphological properties of the limestone using X-ray fluorescence (X-RF), X-ray diffraction (X-RD), Fourier transform infrared spectroscopy (FTIR), and Scanning electron microscopy / energy dispersive x-ray spectroscopy (SEM-EDS) respectively. Raw materials (limestone rocks) were collected from Bukit Keteri area, Chuping, Kangar, Perlis, Malaysia. Lab crusher and lab sieved were utilized to prepare five different size of ground limestone at (75 µm, 150 µm, 225 µm, 300, and 425 µm) respectively. It is found that the main chemical composition of bulk limestone was Calcium oxide (CaO) at 97.58 wt.% and trace amount of MnO, Al2O3, and Fe2O3 at 0.02%, 0.35%, and 0.396% respectively. XRD diffractograms showed characteristic peaks of calcite and quartz. Furthermore, main FTIR absorption bands at 1,419, 874.08 and 712.20 cm-1 indicated the presence of calcite. The micrographs showed clearly the difference of samples particle size. Furthermore, EDS peaks of Ca, O, and C elements confirmed the presence of CaCO3 in the samples.

Quality Characterization of Iron Dust Exhaust Thermal as Alternative Ceramic Coating Raw Materials in a Brazilian Company

2014 ◽  
Vol 1077 ◽  
pp. 135-138
Author(s):  
Luiz Oliveira Veriano dalla Valentina ◽  
Marilena Valadares Folgueras ◽  
Wanessa Rejane Knop ◽  
Maria Cristina Pacheco do Nascimento ◽  
Glaucia Aparecida Prates
Keyword(s):  
Ceramic Coating ◽  
Raw Materials ◽  
Ceramic Materials ◽  
Raw Material ◽  
Silica Sand ◽  
Commercial Application ◽  
X Ray Diffraction ◽  
X Ray ◽  
Materials Used

As the raw materials used in the ceramic materials manufacturing are natural, it is important to use them as a alternative materials, thus decreasing the elements demand taken from nature. This paper aims the characterization of foundry solid powder exhaust from a brazilian company located in Joinville - SC as an alternative raw material for ceramic coating by X-ray diffraction (XRD), thermal analysis (DSC) and thermogravimetric (TG). The dust depletion is caused in the manufacturing mold sand process, when the bentonita (clay), silica sand and coal during the metal parts production are mixed in green sand production. The raw materials were characterized through X-ray diffraction (XRD), thermal (DSC) and thermogravimetric analisys (TG). The atomized powder thermogravimetric analysis curve shows three intervals associated with the mass loss and it is typical of clay commercial application.

Development and Characterization of Al2O3-ZrO2 Composites Using ZrO2(Y2O3)-Recycled as Raw Material

2018 ◽  
Vol 912 ◽  
pp. 124-129
Author(s):  
Caio Marcelo Felbinger Azevedo Cossu ◽  
Manuel Fellipe Rodrigues Pais Alves ◽  
Luiz Cláudio Lemos de Assis ◽  
Roberto de Oliveira Magnago ◽  
José Vitor Candido de Souza ◽  
...  
Keyword(s):  
Fracture Toughness ◽  
Relative Density ◽  
Raw Materials ◽  
Ceramic Composites ◽  
Raw Material ◽  
X Ray Diffraction ◽  
X Ray ◽  
Dental Prostheses ◽  
Scanning Electron

The objective of this work was the development of Al2O3-ZrO2 ceramic composites using recycled-source of ZrO2(Y2O3). Al2O3 powder was mixed with different proportions of ZrO2(Y2O3) arising from pre-sintered blocks used in dental prostheses manufacturing. The mixtures containing 3wt% to 15wt% ZrO2(Y2O3) were uniaxially pressed at 80MPa and sintered at 1600°C-2h. Raw materials and sintered samples were characterized by X-ray diffraction, scanning electron microscopy (SEM), relative density, hardness and fracture toughness. The results of X-ray diffraction showed α-Al2O3 and tetragonal-ZrO2 as crystalline phases after sintering. Furthermore, the relative density in all compositions was higher than 95%. The samples presented Vickers hardness and fracture toughness higher than 1300HV and 3.5MPa. m1/2, respectively.

Characterization and A Preliminary Study of TiO2 Synthesis from Lampung Iron Sand

2020 ◽  
Vol 849 ◽  
pp. 113-118
Author(s):  
Yayat Iman Supriyatna ◽  
Slamet Sumardi ◽  
Widi Astuti ◽  
Athessia N. Nainggolan ◽  
Ajeng W. Ismail ◽  
...  
Keyword(s):  
Food Packaging ◽  
Xrd Analysis ◽  
Major Elements ◽  
Raw Material ◽  
Solid Residue ◽  
X Ray Diffraction ◽  
X Ray ◽  
Leaching Solution ◽  
Ti Content

The purpose of this study is to characterize Lampung iron sand and to conduct preliminary experiments on the TiO2 synthesis which can be used for the manufacturing of functional food packaging. The iron sand from South Lampung Regency, Lampung Province that will be utilized as raw material. The experiment was initiated by sieving the iron sand on 80, 100, 150, 200 and 325 mesh sieves. Analysis using X-Ray Fluorescence (XRF) to determine the element content and X-Ray Diffraction (XRD) to observe the mineralization of the iron sand was conducted. The experiment was carried out through the stages of leaching, precipitation, and calcination. Roasting was applied firstly by putting the iron sand into the muffle furnace for 5 hours at a temperature of 700°C. Followed by leaching using HCl for 48 hours and heated at 105°C with a stirring speed of 300 rpm. The leaching solution was filtered with filtrate and solid residue as products. The solid residue was then leached using 10% H2O2 solution. The leached filtrate was heated at 105°C for 40 minutes resulting TiO2 precipitates (powder). Further, the powder was calcined and characterized. Characterization of raw material using XRF shows the major elements of Fe, Ti, Mg, Si, Al and Ca. The highest Ti content is found in mesh 200 with 9.6%, while iron content is about 80.7%. While from the XRD analysis, it shows five mineral types namely magnetite (Fe3O4), Rhodonite (Mn, Fe, Mg, Ca) SiO3, Quart (SiO2), Ilmenite (FeOTiO2) and Rutile (TiO2). The preliminary experiment showed that the Ti content in the synthesized TiO2 powder is 21.2%. The purity of TiO2 is low due to the presence of Fe metal which is dissolved during leaching, so that prior to precipitation purification is needed to remove impurities such as iron and other metals.

Preliminary Preparation and Characterization Studies of Cellulose from Merbau (Intsia bijuga)

2012 ◽  
Vol 620 ◽  
pp. 314-319
Author(s):  
Nur Amira Mamat Razali ◽  
Fauziah Abdul Aziz ◽  
Saadah Abdul Rahman
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Alkaline Treatment ◽  
Raw Material ◽  
X Ray Diffraction ◽  
X Ray ◽  
Preliminary Preparation ◽  
Characterization Studies ◽  
Scanning Electron

Hardwood is wood from angiosperm trees. The characteristic of hardwood include flowers, endosperm within seeds and the production of fruits that contain the seeds. This paper aims to discuss the preparation and characterization of cellulose obtained from hardwood. The hardwood Merbau (Intsia bijuga) was chosen as raw material in this study. Alkaline treatment and delignification methods were used for the preparation of cellulose. Acid hydrolysis was employed to produce cellulose nanocrystal (CNC). The treated and untreated samples were characterized using x-ray diffraction (XRD) and field emission scanning electron microscopy (FE-SEM). The final product, from both trated and untreated samples were then compared.

scholarly journals Making and Characterization of Limnpo4 Using Solid State Reaction Method for Lithium Ion Battery Cathodes

2019 ◽  
pp. 583-588
Author(s):  
Adelyna Oktavia ◽  
Kurnia Sembiring ◽  
Slamet Priyono
Keyword(s):  
Solid State ◽  
Lithium Ion Battery ◽  
Lithium Ion ◽  
Solid State Reaction Method ◽  
Raw Material ◽  
X Ray Diffraction ◽  
Solid State Method ◽  
X Ray ◽  
General Investigation

Hospho-material of olivine, LiMnPO4 identified as promising for cathode material generation next Lithium-ion battery and has been successfully synthesized by solid-state method with Li2Co3, 2MnO2, 2NH4H2PO4 as raw material. The influence of initial concentration of precursors at kalsinasi temperatures (400-800 ° C) flows with nitrogen. The purity and composition phase verified by x-ray diffraction analysis (XRD), scanning electron microscopy (SEM), spectroscopy, energy Dispersive x-ray Analysis (EDS), Raman spectra. General investigation shows that there is a correlation between the concentration of precursors, the temperature and the temperature of sintering kalsinasi that can be exploited to design lithium-ion next generation.

Mineralogical and geochemical characterization of archaeological ceramics from the 16th century El Badi Palace, Morocco

Clay Minerals ◽  
2018 ◽  
Vol 53 (3) ◽  
pp. 459-470
Author(s):  
Mouhssin El Halim ◽  
Lahcen Daoudi ◽  
Meriam El Ouahabi ◽  
Valérie Rousseau ◽  
Catherine Cools ◽  
...  
Keyword(s):  
Sixteenth Century ◽  
Chemical Characterization ◽  
Raw Material ◽  
Maximum Temperature ◽  
X Ray Diffraction ◽  
Archaeological Ceramics ◽  
Geochemical Characterization ◽  
X Ray ◽  
Firing Tests

ABSTRACTTextural, mineralogical and chemical characterization of archaeological ceramics (zellige) from El Badi Palace (Marrakech, Morocco), the main Islamic monument from the Saadian period (sixteenth century), has been performed to enhance restoration and to determine the technology of manufacturing. A multi-analytical approach based on optical and scanning electron microscopy, cathodoluminescence, X-ray fluorescence and X-ray diffraction was used. Re-firing tests on ceramic supports were also performed to determine the firing temperatures used by the Saadian artisans. A calcareous clay raw material was used to manufacture these decorative ceramics. The sherds were fired at a maximum temperature of 800°C in oxidizing atmosphere. The low firing temperature for ‘zellige’ facilitates cutting of the pieces, but also causes fragility in these materials due to the absence of vitreous phases.

Synthesis and Characterization of ALaFeNi0.5W0.5O6 (A= Sr or Ca), a New Structure Distorted Double Perovskite

2013 ◽  
Vol 717 ◽  
pp. 133-138
Author(s):  
A. Awad Allah ◽  
M. Elhadi ◽  
O.A. Yassien
Keyword(s):  
Crystal Structure ◽  
Diffraction Data ◽  
Double Perovskite ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Absorption Bands ◽  
X Ray ◽  
Perovskite Materials ◽  
Ftir Spectrometer

The crystal structure of both samples has been solved by powder X-ray diffraction, data in the tetragonal space group I4/m (a= b= 5.55182 Å, c =7.86955 A0) for SrLaFeNi0.5W0.5O6sample and (a=b= 5.49129Å, c= 7.82233Å) for CaLaFeNi0.5W0.5O6 sample, and shows an almost perfect ordering between Ni2+ and W5+ cations at the B-site of the perovskite structure. The FTIR spectrometer used of the powders showed that the spectra of both are very similar, showing two strong and well-defined absorption bands, typical of perovskite materials.

scholarly journals Use of basaltic waste as red ceramic raw material

Cerâmica ◽  
2016 ◽  
Vol 62 (362) ◽  
pp. 157-162 ◽  
Author(s):  
T. M. Mendes ◽  
G. Morales ◽  
P. J. Reis
Keyword(s):  
Size Distribution ◽  
Mechanical Performance ◽  
Raw Materials ◽  
Raw Material ◽  
Metropolitan Region ◽  
X Ray Diffraction ◽  
X Ray ◽  
Microstructure Evaluation ◽  
Firing Shrinkage ◽  
Physical And Chemical

Abstract Nowadays, environmental codes restrict the emission of particulate matters, which result in these residues being collected by plant filters. This basaltic waste came from construction aggregate plants located in the Metropolitan Region of Londrina (State of Paraná, Brazil). Initially, the basaltic waste was submitted to sieving (< 75 μm) and the powder obtained was characterized in terms of density and particle size distribution. The plasticity of ceramic mass containing 0%, 10%, 20%, 30%, 40% and 50% of basaltic waste was measured by Atterberg method. The chemical composition of ceramic formulations containing 0% and 20% of basaltic waste was determined by X-ray fluorescence. The prismatic samples were molded by extrusion and fired at 850 °C. The specimens were also tested to determine density, water absorption, drying and firing shrinkages, flexural strength, and Young's modulus. Microstructure evaluation was conducted by scanning electron microscopy, X-ray diffraction, and mercury intrusion porosimetry. Basaltic powder has similar physical and chemical characteristics when compared to other raw materials, and contributes to ceramic processing by reducing drying and firing shrinkage. Mechanical performance of mixtures containing basaltic powder is equivalent to mixtures without waste. Microstructural aspects such as pore size distribution were modified by basaltic powder; albite phase related to basaltic powder was identified by X-ray diffraction.

Characterization of Spherical Molybdenum Powders Prepared by RF Plasma Processing

2012 ◽  
Vol 482-484 ◽  
pp. 2563-2567 ◽  
Author(s):  
Yan Wei Sheng ◽  
Zhi Meng Guo ◽  
Jun Jie Hao
Keyword(s):  
Feeding Rate ◽  
Morphological Properties ◽  
Narrow Particle Size Distribution ◽  
Rf Plasma ◽  
X Ray Diffraction ◽  
X Ray ◽  
Plasma Spheroidization ◽  
Powder Characteristics ◽  
Near Net Shape

Spherical molybdenum powders were synthesized by (RF) plasma with irregular molybdenum powders. The powder characteristics and spheroidization efficiency of the feeding rate for obtain the spherical molybdenum powders were studied. The phase composition and morphological properties of the powders were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM). As a result, the fine spherical powders composed of pure molybdenum with favorable dispersity and its surface became smooth. The spheroidization efficiency of synthesized powders was almost 100 % at feeding rate of 5g/min. LMS analysis indicated that the as-prepared powder had narrow particle size distribution and the spheroidization efficiency of the sample decreases gradually as increasing of the feeding rate. The RF plasma spheroidization of molybdenum powder is an ideal route synthesis of well- spherical molybdenum powders used as near net-shape technology and powder metallurgy.

Effect of Barium Aluminates on Acid Resistance of Fracturing Proppants

2011 ◽  
Vol 383-390 ◽  
pp. 3291-3297
Author(s):  
Shiao Zhao ◽  
Bo Lin Wu ◽  
Shuo Qin ◽  
Yan Rong Zhao ◽  
Zu Sheng Hu
Keyword(s):  
Mass Fraction ◽  
Barium Carbonate ◽  
Raw Materials ◽  
Acid Resistance ◽  
Raw Material ◽  
X Ray Diffraction ◽  
Free System ◽  
X Ray ◽  
Acid Solubility ◽  
Industrial Standards

In order to explore the effect of removing siliceous components on acid resistance of fracturing proppants, acid resistance of fracturing proppants in a new silicon-free system was studied in this paper. The fracturing proppants were made by pressureless sintering using high-purity alumina and barium carbonate as the basic raw material. Acid resistance test was carried out in 12 wt% HCl + 3 wt% HF at 65 oC for 30 minutes according to The Petroleum and Gas Industrial Standards of China (SY/T5108-2006) and morphology, structure and chemical analysis of the samples were investigated using X-ray diffraction and scanning electron microscopy. Experiments show that fracturing proppants that contain barium aluminates have better acid resistance. The acid solubility of the samples is less than 3%, especially when the content of barium carbonate is about 10% (mass fraction, the same below), the acid solubility of the sample reaches 0.52% which is far beyond the demands (5%) of the Standards of SY/T5108-2006. Results prove that the removal of siliceous components of raw materials can prominently improve the acid resistance of fracturing proppants. It can provide a new referential thought for improving the acid resistance of fracturing proppants.

Sign in / Sign up

Export Citation Format

Share Document