scholarly journals CORRECTION OF POLYRIBOSOME DISTRIBUTIONS AS OBSERVED IN CELL SECTIONS BY ELECTRON MICROSCOPY

1964 ◽  
Vol 22 (3) ◽  
pp. 613-621 ◽  
Author(s):  
William Perl
Keyword(s):  
Electron Microscopy ◽  
Probability Method ◽  
Section Thickness ◽  
Thin Sections ◽  
Comparison Of The Results ◽  
Good Agreement ◽  
Rabbit Reticulocytes

Clusters of ribosomes observed by electron microscopy in thin sections of rabbit reticulocytes are of the same order of size as the section thickness of 600 A. Many of the observed clusters must therefore have been transected by the section surfaces and observed as clusters containing fewer ribosomes. A probability method of correcting for this effect is given. Comparison of the results with grid observations of ribosome distributions indicates sufficiently good agreement for application to cell section observations.

scholarly journals Improved Sectioning of Polymers Using an Oscillating Diamond Knife for Transmission Electron Microscopy

2006 ◽  
Vol 14 (5) ◽  
pp. 20-21 ◽  
Author(s):  
J.D. Harris ◽  
J.S. Vastenhout
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Wedge Angle ◽  
Cutting Speed ◽  
Sample Surface ◽  
Section Thickness ◽  
Thin Sections ◽  
Transmission Electron ◽  
Surface Section ◽  
Diamond Knife

Polymers are viscoelastic materials that can often deform during microtome sectioning. Similar to plastic embedded biological materials, many methods have been developed over the years to not only improve the image contrast of these materials but also to harden the material for improved sectioning during microtomy. Even with these improvements, a common artifact, compression, during the sectioning of this class of materials remains problematic.Compression is caused by several factors: hardness of the sample, embedding media, wedge angle of the knife, interaction between the diamond and sample surface, section thickness and cutting speed. It has been found that reducing the knife angle from 45º to 35° leads to a reduction in compression. Recent efforts to further reduce the compression of ultra-thin sections have led to the invention of an oscillating diamond knife.

Two- or three-way observations of the identical cell elements within the same sections by LM, TEM and/or SEM

1978 ◽  
Vol 36 (2) ◽  
pp. 82-83 ◽  
Author(s):  
Nakazo Watari ◽  
Yasuaki Hotta ◽  
Yoshio Mabuchi
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Fine Structure ◽  
Light Microscopy ◽  
Thin Sections ◽  
Transmission Electron ◽  
Identical Cell ◽  
Electron Microscopes ◽  
Scanning Electron

It is very useful if we can observe the identical cell elements within the same sections by light microscopy (LM), transmission electron microscopy (TEM) and/or scanning electron microscopy (SEM) sequentially, because, the cell fine structure can not be indicated by LM, while the color is; on the other hand, the cell fine structure can be very easily observed by EM, although its color properties may not. However, there is one problem in that LM requires thick sections of over 1 μm, while EM needs very thin sections of under 100 nm. Recently, we have developed a new method to observe the same cell elements within the same plastic sections using both light and transmission (conventional or high-voltage) electron microscopes.In this paper, we have developed two new observation methods for the identical cell elements within the same sections, both plastic-embedded and paraffin-embedded, using light microscopy, transmission electron microscopy and/or scanning electron microscopy (Fig. 1).

Lead aspartate: a new en bloc stain for electron microscopy

1978 ◽  
Vol 36 (2) ◽  
pp. 34-35
Author(s):  
J.R. Walton
Keyword(s):  
Electron Microscopy ◽  
Calcium Ion ◽  
Enzyme Reaction ◽  
Lead Citrate ◽  
Reaction Products ◽  
En Bloc ◽  
Thin Sections ◽  
Lead Salts ◽  
Thin Sectioning ◽  
High Alkalinity

In electron microscopy, lead is the metal most widely used for enhancing specimen contrast. Lead citrate requires a pH of 12 to stain thin sections of epoxy-embedded material rapidly and intensively. However, this high alkalinity tends to leach out enzyme reaction products, making lead citrate unsuitable for many cytochemical studies. Substitution of the chelator aspartate for citrate allows staining to be carried out at pH 6 or 7 without apparent effect on cytochemical products. Moreover, due to the low, controlled level of free lead ions, contamination-free staining can be carried out en bloc, prior to dehydration and embedding. En bloc use of lead aspartate permits the grid-staining step to be bypassed, allowing samples to be examined immediately after thin-sectioning.Procedures. To prevent precipitation of lead salts, double- or glass-distilled H20 used in the stain and rinses should be boiled to drive off carbon dioxide and glassware should be carefully rinsed to remove any persisting traces of calcium ion.

Ectodesmata as Revealed By Freeze-Etch Preparations of Plant Epidermal Cell Walls

1973 ◽  
Vol 31 ◽  
pp. 468-469
Author(s):  
N.C. Lyon ◽  
W. C. Mueller
Keyword(s):  
Electron Microscopy ◽  
Acetic Acid ◽  
Nitric Acid ◽  
Oxalic Acid ◽  
Light Microscopy ◽  
Epidermal Cell ◽  
Cell Walls ◽  
Plant Viruses ◽  
Plant Leaves ◽  
Thin Sections

Schumacher and Halbsguth first demonstrated ectodesmata as pores or channels in the epidermal cell walls in haustoria of Cuscuta odorata L. by light microscopy in tissues fixed in a sublimate fixative (30% ethyl alcohol, 30 ml:glacial acetic acid, 10 ml: 65% nitric acid, 1 ml: 40% formaldehyde, 5 ml: oxalic acid, 2 g: mecuric chloride to saturation 2-3 g). Other workers have published electron micrographs of structures transversing the outer epidermal cell in thin sections of plant leaves that have been interpreted as ectodesmata. Such structures are evident following treatment with Hg++ or Ag+ salts and are only rarely observed by electron microscopy. If ectodesmata exist without such treatment, and are not artefacts, they would afford natural pathways of entry for applied foliar solutions and plant viruses.

High-resolution scanning electron microscopy (HRSEM) of mitochondria from various rat tissues

1988 ◽  
Vol 46 ◽  
pp. 14-15
Author(s):  
P.J. Lea ◽  
M.J. Hollenberg
Keyword(s):  
Electron Microscopy ◽  
Pigment Epithelium ◽  
Retinal Pigment ◽  
Rat Hepatocytes ◽  
Three Dimensions ◽  
Objective Lens ◽  
Rat Tissues ◽  
Thin Sections ◽  
Reconstruction Methods ◽  
Scanning Electron

Our current understanding of mitochondrial ultrastructure has been derived primarily from thin sections using transmission electron microscopy (TEM). This information has been extrapolated into three dimensions by artist's impressions (1) or serial sectioning techniques in combination with computer processing (2). The resolution of serial reconstruction methods is limited by section thickness whereas artist's impressions have obvious disadvantages.In contrast, the new techniques of HRSEM used in this study (3) offer the opportunity to view simultaneously both the internal and external structure of mitochondria directly in three dimensions and in detail.The tridimensional ultrastructure of mitochondria from rat hepatocytes, retinal (retinal pigment epithelium), renal (proximal convoluted tubule) and adrenal cortex cells were studied by HRSEM. The specimens were prepared by aldehyde-osmium fixation in combination with freeze cleavage followed by partial extraction of cytosol with a weak solution of osmium tetroxide (4). The specimens were examined with a Hitachi S-570 scanning electron microscope, resolution better than 30 nm, where the secondary electron detector is located in the column directly above the specimen inserted within the objective lens.

Lattice imaging and pore structure of β ferric oxyhydroxide

1978 ◽  
Vol 36 (1) ◽  
pp. 264-265
Author(s):  
T. Baird ◽  
J.R. Fryer ◽  
S.T. Galbraith
Keyword(s):  
Electron Microscopy ◽  
Room Temperature ◽  
Bulk Material ◽  
Model Structure ◽  
Bulk Crystals ◽  
Lattice Imaging ◽  
Thin Sections ◽  
Ferric Oxyhydroxide ◽  
Resolution Electron ◽  
Hydrolysis Of

Introduction Previously we had suggested (l) that the striations observed in the pod shaped crystals of β FeOOH were an artefact of imaging in the electron microscope. Contrary to this adsorption measurements on bulk material had indicated the presence of some porosity and Gallagher (2) had proposed a model structure - based on the hollandite structure - showing the hollandite rods forming the sides of 30Å pores running the length of the crystal. Low resolution electron microscopy by Watson (3) on sectioned crystals embedded in methylmethacrylate had tended to support the existence of such pores.We have applied modern high resolution techniques to the bulk crystals and thin sections of them without confirming these earlier postulatesExperimental β FeOOH was prepared by room temperature hydrolysis of 0.01M solutions of FeCl3.6H2O, The precipitate was washed, dried in air, and embedded in Scandiplast resin. The sections were out on an LKB III Ultramicrotome to a thickness of about 500Å.

On the High Voltage Electron Microscopy (1 MeV) of Biological Thick Sections

1972 ◽  
Vol 30 ◽  
pp. 464-465
Author(s):  
William H. Massover
Keyword(s):  
Electron Microscopy ◽  
High Voltage ◽  
Present Report ◽  
Biological Tissues ◽  
Specimen Preparation ◽  
Technical Problems ◽  
High Voltage Electron Microscopy ◽  
Thin Sections ◽  
Voltage Electron ◽  
High Voltage Electron

Stereoscopic examination of thick sections of fixed and embedded biological tissues by high voltage electron microscopy has been shown to allow direct visualization of three-dimensional fine structure. The present report will consider the occurrence of some new technical problems in specimen preparation and Image interpretation that are not common during lower voltage studies of thin sections.Thick Sectioning and Tissue Coloration - Epon sections of 0.5 μm or more that are cut with glass knives do not have a uniform thickness as Judged by their interference colors; these colors change with time during their flotation on the knife bath, and again when drying onto the specimen support. Quoted thicknesses thus must be considered only as rough estimates unless measured in specific regions by other methods. Chloroform vapors do not always result in good spreading of thick sections; however, they will spread spontaneously to large degrees after resting on the flotation bath for several minutes. Ribbons of thick sections have been almost impossible to obtain.

Dislocations in alumina deformed by prismatic slip

1978 ◽  
Vol 36 (1) ◽  
pp. 606-607
Author(s):  
J. Cadoz ◽  
J. Castaing ◽  
J. Philibert
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Basal Slip ◽  
Prismatic Slip ◽  
Compression Tests ◽  
Thin Sections ◽  
Burgers Vector ◽  
Maximum Deformation ◽  
Transmission Electron ◽  
Mechanical Thinning

Plastic deformation of alumina has been much studied; basal slip occurs and dislocation structures have been investigated by transmission electron microscopy (T.E.M.) (1). Non basal slip has been observed (2); the prismatic glide system <1010> {1210} has been obtained by compression tests between 1400°C and 1800°C (3). Dislocations with <0110> burgers vector were identified using a 100 kV microscope(4).We describe the dislocation structures after prismatic slip, using high voltage T.E.M. which gives much information.Compression tests were performed at constant strainrate (∿10-4s-1); the maximum deformation reached was 0.03. Thin sections were cut from specimens deformed at 1450°C, either parallel to the glide plane or perpendicular to the glide direction. After mechanical thinning, foils were produced by ion bombardment. Details on experimental techniques can be obtained through reference (3).

Some early history of replica techniques for electron microscopy

1992 ◽  
Vol 50 (2) ◽  
pp. 1076-1077
Author(s):  
Robert M. Fisher
Keyword(s):  
Thin Film ◽  
Electron Microscopy ◽  
Optical Microscope ◽  
Early History ◽  
Bulk Materials ◽  
Thin Sections ◽  
Transmission Electron ◽  
Reflected Light ◽  
History Of ◽  
Electron Microscopes

By 1940, a half dozen or so commercial or home-built transmission electron microscopes were in use for studies of the ultrastructure of matter. These operated at 30-60 kV and most pioneering microscopists were preoccupied with their search for electron transparent substrates to support dispersions of particulates or bacteria for TEM examination and did not contemplate studies of bulk materials. Metallurgist H. Mahl and other physical scientists, accustomed to examining etched, deformed or machined specimens by reflected light in the optical microscope, were also highly motivated to capitalize on the superior resolution of the electron microscope. Mahl originated several methods of preparing thin oxide or lacquer impressions of surfaces that were transparent in his 50 kV TEM. The utility of replication was recognized immediately and many variations on the theme, including two-step negative-positive replicas, soon appeared. Intense development of replica techniques slowed after 1955 but important advances still occur. The availability of 100 kV instruments, advent of thin film methods for metals and ceramics and microtoming of thin sections for biological specimens largely eliminated any need to resort to replicas.

Surface reconstructions of (001) cleaved GdBa2Cu3O7-δ

1992 ◽  
Vol 50 (1) ◽  
pp. 106-107
Author(s):  
H.W. Zandbergen ◽  
M.R. McCartney
Keyword(s):  
Electron Microscopy ◽  
Copper Oxide ◽  
Grain Boundaries ◽  
Atomic Structure ◽  
Oxygen Deficiency ◽  
Surface Layers ◽  
Layer Sequence ◽  
Surface Reconstructions ◽  
Good Agreement

Very few electron microscopy papers have been published on the atomic structure of the copper oxide based superconductor surfaces. Zandbergen et al. have reported that the surface of YBa2Cu3O7-δ was such that the terminating layer sequence is bulk-Y-CuO2-BaO-CuO-BaO, whereas the interruption at the grain boundaries is bulk-Y-CuO2-BaO-CuO. Bursill et al. reported that HREM images of the termination at the surface are in good agreement with calculated images with the same layer sequence as observed by Zandbergen et al. but with some oxygen deficiency in the two surface layers. In both studies only one or a few surfaces were studied.

Sign in / Sign up

Export Citation Format

Share Document