Graphene growth with no intended carbon precursor feeding into the LPCVD process: causes, solutions, and effects

2020 ◽  
Vol 32 (2) ◽  
pp. 025604
Author(s):  
Maryam Mirzaei ◽  
Seyed Mahdi Hedayat ◽  
Javad Karimi-Sabet ◽  
Jafar Towfighi Darain
2016 ◽  
Author(s):  
M. J. Salifairus ◽  
S. B. Abd Hamid ◽  
Salman A. H. Alrokayan ◽  
Haseeb A. Khan ◽  
M. Rusop

Molecules ◽  
2021 ◽  
Vol 26 (15) ◽  
pp. 4660
Author(s):  
Marta Klimek-Szczykutowicz ◽  
Michał Dziurka ◽  
Ivica Blažević ◽  
Azra Đulović ◽  
Małgorzata Miazga-Karska ◽  
...  

The study demonstrated the effects of precursor feeding on the production of glucosinolates (GSLs), flavonoids, polyphenols, saccharides, and photosynthetic pigments in Nasturtium officinale microshoot cultures grown in Plantform bioreactors. It also evaluated the antioxidant and antimicrobial activities of extracts. L-phenylalanine (Phe) and L-tryptophan (Trp) as precursors were tested at 0.05, 0.1, 0.5, 1.0, and 3.0 mM. They were added at the beginning (day 0) or on day 10 of the culture. Microshoots were harvested after 20 days. Microshoots treated with 3.0 mM Phe (day 0) had the highest total GSL content (269.20 mg/100 g DW). The qualitative and quantitative profiles of the GSLs (UHPLC-DAD-MS/MS) were influenced by precursor feeding. Phe at 3.0 mM stimulated the best production of 4-methoxyglucobrassicin (149.99 mg/100 g DW) and gluconasturtiin (36.17 mg/100 g DW). Total flavonoids increased to a maximum of 1364.38 mg/100 g DW with 3.0 mM Phe (day 0), and polyphenols to a maximum of 1062.76 mg/100 g DW with 3.0 mM Trp (day 0). The precursors also increased the amounts of p-coumaric and ferulic acids, and rutoside, and generally increased the production of active photosynthetic pigments. Antioxidant potential increased the most with 0.1 mM Phe (day 0) (CUPRAC, FRAP), and with 0.5 mM Trp (day 10) (DPPH). The extracts of microshoots treated with 3.0 mM Phe (day 0) showed the most promising bacteriostatic activity against microaerobic Gram-positive acne strains (MIC 250–500 µg/mL, 20–21 mm inhibition zones). No extract was cytotoxic to normal human fibroblasts over the tested concentration range (up to 250 μg/mL).


2013 ◽  
Vol 740-742 ◽  
pp. 323-326
Author(s):  
Kassem Alassaad ◽  
François Cauwet ◽  
Davy Carole ◽  
Véronique Soulière ◽  
Gabriel Ferro

Abstract. In this paper, conditions for obtaining high growth rate during epitaxial growth of SiC by vapor-liquid-solid mechanism are investigated. The alloys studied were Ge-Si, Al-Si and Al-Ge-Si with various compositions. Temperature was varied between 1100 and 1300°C and the carbon precursor was either propane or methane. The variation of layers thickness was studied at low and high precursor partial pressure. It was found that growth rates obtained with both methane and propane are rather similar at low precursor partial pressures. However, when using Ge based melts, the use of high propane flux leads to the formation of a SiC crust on top of the liquid, which limits the growth by VLS. But when methane is used, even at extremely high flux (up to 100 sccm), no crust could be detected on top of the liquid while the deposit thickness was still rather small (between 1.12 μm and 1.30 μm). When using Al-Si alloys, no crust was also observed under 100 sccm methane but the thickness was as high as 11.5 µm after 30 min growth. It is proposed that the upper limitation of VLS growth rate depends mainly on C solubility of the liquid phase.


2009 ◽  
Vol 80 (23) ◽  
Author(s):  
E. Starodub ◽  
S. Maier ◽  
I. Stass ◽  
N. C. Bartelt ◽  
P. J. Feibelman ◽  
...  

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1313
Author(s):  
Andreas Hoffmann ◽  
Alexander J. C. Kuehne

Carbon nanofiber nonwovens are promising materials for electrode or filtration applications; however, their utilization is obviated by a lack of high throughput production methods. In this study, we utilize a highly effective high-throughput method for the fabrication of polyacrylonitrile (PAN) nanofibers as a nonwoven on a dedicated substrate. The method employs rotational-, air pressure- and electrostatic forces to produce fibers from the inner edge of a rotating bell towards a flat collector. We investigate the impact of all above-mentioned forces on the fiber diameter, morphology, and bundling of the carbon-precursor PAN fibers. The interplay of radial forces with collector-facing forces has an influence on the uniformity of fiber deposition. Finally, the obtained PAN nanofibers are converted to carbon nonwovens by thermal treatment.


2021 ◽  
Author(s):  
Christin Gellrich ◽  
Stefanie Lochmann ◽  
Thomas Otto ◽  
Julia Grothe ◽  
Stefan Kaskel

A highly energetic carbon precursor suitable for soft lithographic processing based on acetylene dicarboxylic acid is presented. High-resolution micro-supercapacitors with line width down to 500 nm are produced using the...


2021 ◽  
Vol 331 ◽  
pp. 124934
Author(s):  
Yuxin Yan ◽  
Yang Meng ◽  
Haitao Zhao ◽  
Edward Lester ◽  
Tao Wu ◽  
...  

2021 ◽  
Author(s):  
E. Rozbiegala ◽  
W. Kaszub ◽  
A. Dobrowolski ◽  
J. Jagiello ◽  
K. Pietak ◽  
...  
Keyword(s):  

Sign in / Sign up

Export Citation Format

Share Document