scholarly journals Effect of Reaction Temperature on Adsorption Efficiency using Computer Mathematical Statistics Visible Spectorphotometer

2021 ◽  
Vol 2083 (3) ◽  
pp. 032072
Author(s):  
Yongli Zhang ◽  
Ruiting Li
Keyword(s):  
Reaction Temperature ◽  
Metal Ion ◽  
Adsorption Rate ◽  
Ion Concentration ◽  
Adsorption Efficiency ◽  
Optimum Temperature ◽  
Absorption Effect ◽  
Before And After ◽  
Measurement Experiment ◽  
Optimal Reaction

Abstract In this paper, waste shrimp shells extracted from the head of the chitosan material; static adsorption experiments manner by wastewater containing Fe(III) added chitosan, vis spectrophotometer absorbance before and after the measurement experiment was obtained by reacting the size of the metal ion concentration, adsorption conditions whereby chitosan Fe(III) and the ability to explore. Experiments show that. In the case where the reaction temperature is less than 55°C, chitosan has adsorption rate Fe(III) smaller rise, the optimum temperature was 55°C, but the effects on the reaction temperature adsorption rate is not large; Adsorption when control time 30 min to 50 min, the absorption effect is increased with increase in the time, to reach the optimal reaction time 50 min.

scholarly journals Adsorptive Removal of Pb(II), Cu(II) and Cd(II) Ions onto Rubus ellipticus as Low-Cost Biosorbent

2020 ◽  
Vol 32 (3) ◽  
pp. 495-500
Author(s):  
Rajesh Kumar ◽  
Harish Sharma ◽  
M.C. Vishwakarma ◽  
S.K. Joshi ◽  
N.S. Bhandari ◽  
...  
Keyword(s):  
Contact Time ◽  
Metal Ion ◽  
Low Cost ◽  
Ion Concentration ◽  
Adsorption Efficiency ◽  
Adsorptive Removal ◽  
Langmuir Adsorption ◽  
Equilibrium Data ◽  
Rubus Ellipticus ◽  
Adsorbent Dose

In the present study, removal efficiency (%) of Rubus ellipticus leaves (REL) as an adsorbent for the removal of Pb(II), Cu(II) and Cd(II) ions was investigated. Different parameters i.e., pH, contact time, temperature, adsorbent dose and initial metal ion concentration were investigated to obtain the optimum adsorption efficiency. At pH 4, a maximum adsorption was 84.6, 80.2 and 74.5 % for Pb(II), Cu(II) and Cd(II) ions, respectively. The maximum adsorption of all the three metal ions obtained at contact time (75 min), initial metal ion concentration (10 mg/L), temperature (25 ºC) and adsorbent dose (5.0 g). The equilibrium adsorption of Pb(II), Cu(II) and Cd(II) ions at different temperature was described by Langmuir, Freundlich and Temkin isotherms. The equilibrium data fitted well the Langmuir adsorption isotherm. Thermodynamic parameters like Gibb′s free energy (ΔGº), enthalpy (ΔHº) and entropy (ΔSº) were also calculated. The calculated parameters indicated that adsorption of Pb(II), Cu(II) and Cd(II) ions onto Rubus ellipticus leaves (REL) was spontaneous (ΔGº < 0), endothermic (ΔGº > 0). The feasibility of the process was evident from the positive value of ΔSº.

scholarly journals Adsorption Capabilities of Activated Carbon Derived from Detarium microcarpum Seeds in Removing Co2+ and Pb2+ from Wastewater

2020 ◽  
pp. 167-179
Author(s):  
Ishaq Yahaya Lawan ◽  
Shinggu D. Yamta ◽  
Abdurrahman Hudu ◽  
Kolo Alhaji Madu ◽  
Adamu Mohammad ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Metal Ion ◽  
Adsorption Process ◽  
Ion Concentration ◽  
Adsorption Efficiency ◽  
Cobalt Ions ◽  
Initial Concentration ◽  
Detarium Microcarpum ◽  
Percentage Removal

This study was carried out to evaluate the efficiency of metals (Pb and Co) removal from solution using Detarium microcarpum seeds as adsorbent. The effect of initial concentration and adsorbent dosage on the adsorption process of these metals were studied, the percentage removal of these metals increased with increased in weight (0.5 -2.5g) in 50ml of the solution and the adsorption efficiency increased with increasing initial metal ion concentration (0.01-0.05 moldm−3). The percentage removal obtained for Lead and Cobalt were compared. The result of adsorption were fitted to Langmuir models and coefficients indicated favorable adsorption of Pb2+ and Co2+ ions on the adsorbents. The adsorption of Pb2+ and Co2+ in aqueous solution was in the following order (1400µm>420µm>150µm). More than 55.4% of studied Lead cations were removed by 1400µm, 47.2% by 420µm and 29.8% by 150µm. While for Cobalt cations only 53.2% by 1400µm, 38.6% by 420µm and 24% by 150µm respectively, from aqueous solution it was concluded that, activated Carbon derived from Detarium microcarpum seed is good in removing both lead and cobalt ions, which make it good absorbent.

scholarly journals ADSORPTION KINETICS OF Pb(II), Cd(II) AND Cr(III) ON ADSORBENT PRODUCED BY PROTECTED-CROSSLINKING OF HUMIC ACID-CHITOSAN

2010 ◽  
Vol 10 (1) ◽  
pp. 80-87
Author(s):  
Dewi Umaningrum ◽  
Uripto Trisno Santoso ◽  
Radna Nurmasari ◽  
Rahmat Yunus
Keyword(s):  
Humic Acid ◽  
Adsorption Kinetics ◽  
Metal Ion ◽  
Second Order ◽  
Adsorption Rate ◽  
Ion Concentration ◽  
Rate Limiting Step ◽  
Limiting Step ◽  
Rate Limiting ◽  
Kinetics Of

Study on adsorption kinetics of of Pb(II), Cd(II) and Cr(III) on adsorbent which was produced by protected-crosslinking of humic acid-chitosan has been done. The Langmuir-Hinshelwood, pseudo first- and second-order kinetics models were used to describe the kinetic data, and the rate constants of adsorption were also evaluated. The experimental data fitted well the second-order kinetics model, indicating that the chemical sorption is the rate-limiting step, instead of mass transfer. The initial metal ion concentration significantly affects the adsorption rate. An increase in initial metal ion concentration results in the decrease in adsorption rate of the metals.   Keywords: kinetics, adsorption, crosslinking, humic acid, chitosan

scholarly journals THERMODYNAMIC OF Mg(II), Cd(II), AND Ni(II) ADSORPTION ON SULFONIC MODIFIED SILICA GEL

2010 ◽  
Vol 5 (1) ◽  
pp. 31-35 ◽  
Author(s):  
Choiril Azmiyawati ◽  
Nuryono Nuryono ◽  
Narsito Narsito
Keyword(s):  
Silica Gel ◽  
Metal Ion ◽  
Ion Concentration ◽  
Chemical Adsorption ◽  
Modified Silica ◽  
Adsorption Parameters ◽  
Modified Silica Gel ◽  
Batch System ◽  
Before And After ◽  
The Difference

Silica gel modified with 4-amino-5-hydroxy-2,7-naphtalenedisulphonate (SG-SO3-) has been applied for adsorption of Mg(II), Cd(II), and Ni(II) in aqueous medium. In addition, three thermodynamic parameters i.e. capacity, adsorption constant and energy of adsorption were calculated. Adsorption was conducted in a batch system and metal ion remaining in the solution was determined by atomic adsorption spectrophotometry (AAS). The amount of adsorbed metal ions was calculated from the difference of metal ion concentration before and after interaction. Adsorption parameters i.e. capacity (ns2), constant (b), and energy (E) of adsorption were calculated using the equation of Langmuir isotherm. Results showed that ns2 for Mg(II), Cd(II), and Ni(II) on the adsorbent were 4.67 x 10-4, 1.19 x 10-4, and 0.13 x 10-4mol g-1, respectively. The values of b for Mg(II), Cd(II), and Ni(II) were 49.35 x 105, 173.46 x 105, and 181.12 x 105 g-1, respectively. Furthermore, it was found that E for all metal ion investigated was in the range of 26-30 kJ/mol, indicating the involvement of chemical adsorption.  

Use of agro-waste (Musa paradisiaca peels) as a sustainable biosorbent for toxic metal ions removal from contaminated water

2019 ◽  
Author(s):  
Chem Int
Keyword(s):  
Heavy Metal ◽  
Metal Ions ◽  
Contact Time ◽  
Metal Ion ◽  
Equilibrium Concentration ◽  
Ion Concentration ◽  
Contaminated Water ◽  
Musa Paradisiaca ◽  
Percentage Removal ◽  
Adsorbent Dose

A study of removal of heavy metal ions from heavy metal contaminated water using agro-waste was carried out with Musa paradisiaca peels as test adsorbent. The study was carried by adding known quantities of lead (II) ions and cadmium (II) ions each and respectively into specific volume of water and adding specific dose of the test adsorbent into the heavy metal ion solution, and the mixture was agitated for a specific period of time and then the concentration of the metal ion remaining in the solution was determined with Perkin Elmer Atomic absorption spectrophotometer model 2380. The effect of contact time, initial adsorbate concentration, adsorbent dose, pH and temperature were considered. From the effect of contact time results equilibrium concentration was established at 60minutes. The percentage removal of these metal ions studied, were all above 90%. Adsorption and percentage removal of Pb2+ and Cd2+ from their aqueous solutions were affected by change in initial metal ion concentration, adsorbent dose pH and temperature. Adsorption isotherm studies confirmed the adsorption of the metal ions on the test adsorbent with good mathematical fits into Langmuir and Freundlich adsorption isotherms. Regression correlation (R2) values of the isotherm plots are all positive (&gt;0.9), which suggests too, that the adsorption fitted into the isotherms considered.

scholarly journals Adsorption Studies on Magnetic Nanoparticles Functionalized with Silver to Remove Nitrates from Waters

Water ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 1757
Author(s):  
Yesica Vicente-Martínez ◽  
Manuel Caravaca ◽  
Antonio Soto-Meca ◽  
Miguel Ángel Martín-Pereira ◽  
María del Carmen García-Onsurbe
Keyword(s):  
Magnetic Nanoparticles ◽  
Nitrate Content ◽  
Adsorption Efficiency ◽  
Experimental Conditions ◽  
Dependent Behavior ◽  
Before And After ◽  
Naoh Solution ◽  
High Concentrations ◽  
Interference Studies

This paper presents a novel procedure for the treatment of contaminated water with high concentrations of nitrates, which are considered as one of the main causes of the eutrophication phenomena. For this purpose, magnetic nanoparticles functionalized with silver (Fe3O4@AgNPs) were synthesized and used as an adsorbent of nitrates. Experimental conditions, including the pH, adsorbent and adsorbate dose, temperature and contact time, were analyzed to obtain the highest adsorption efficiency for different concentration of nitrates in water. A maximum removal efficiency of 100% was reached for 2, 5, 10 and 50 mg/L of nitrate at pH = 5, room temperature, and 50, 100, 250 and 500 µL of Fe3O4@AgNPs, respectively. The characterization of the adsorbent, before and after adsorption, was performed by energy dispersive X-ray spectroscopy, scanning electron microscopy, Brunauer-Emmett-Teller analysis and Fourier-transform infrared spectroscopy. Nitrates can be desorbed, and the adsorbent can be reused using 500 µL of NaOH solution 0.01 M, remaining unchanged for the first three cycles, and exhibiting 90% adsorption efficiency after three regenerations. A deep study on equilibrium isotherms reveals a pH-dependent behavior, characterized by Langmuir and Freundlich models at pH = 5 and pH = 1, respectively. Thermodynamic studies were consistent with physicochemical adsorption for all experiments but showed a change from endothermic to exothermic behavior as the temperature increases. Interference studies of other ions commonly present in water were carried out, enabling this procedure as very selective for nitrate ions. In addition, the method was applied to real samples of seawater, showing its ability to eliminate the total nitrate content in eutrophized waters.

scholarly journals Chemical Composition and Corrosion Behavior of a-C:H/DLC Film-Coated Titanium Substrate in Simulated PEMFC Environment

Coatings ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 820
Author(s):  
Beibei Han ◽  
Mengyuan Yan ◽  
Dongying Ju ◽  
Maorong Chai ◽  
Susumu Sato
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Behavior ◽  
Metal Ion ◽  
Ion Beam ◽  
Titanium Substrate ◽  
Corrosion Current ◽  
Ion Concentration ◽  
Bipolar Plates ◽  
High Adhesion ◽  
Corrosion Behaviors

The amorphous hydrogenated (a-C:H) film-coated titanium, using different CH4/H2 and deposition times, was prepared by the ion beam deposition (IBD) method, which has the advantage of high adhesion because of the graded interface mixes at the atomic level. The chemical characterizations and corrosion behaviors of a-C:H film were investigated and evaluated by SEM, AFM, Raman spectroscopy, EPMA, TEM and XPS. An a-C:H film-coated titanium was corroded at 0.8 V, 90 °C in a 0.5 mol/L H2SO4 solution for 168 h. The metal ion concentration in the H2SO4 corrosion solution and the potentiodynamic polarization behavior were evaluated. Results indicate that a higher CH4/H2 of 1:0 and a deposition time of 12 h can result in a minimum ID/IG ratio of 0.827, Ra of 5.76 nm, metal ion concentration of 0.34 ppm in the corrosion solution and a corrosion current of 0.23 µA/cm2. The current density in this work meets the DOE’s 2020 target of 1 µA/cm2. Electrical conductivity is inversely proportional to the corrosion resistance. The significant improvement in the corrosion resistance of the a-C:H film was mainly attributed to the increased sp3 element and nanocrystalline TiC phase in the penetration layer. As a result, the a-C:H film-coated titanium at CH4/H2 = 1:0 with improved anti-corrosion behavior creates a great potential for PEMFC bipolar plates.

scholarly journals Synthesis of propylene carbonate from urea and 1,2-propylene glycol over metal carbonates

2011 ◽  
Vol 17 (3) ◽  
pp. 323-331 ◽  
Author(s):  
Jiancheng Zhou ◽  
Wu Dongfang ◽  
Birong Zhang ◽  
Yali Guo
Keyword(s):  
Reaction Time ◽  
Propylene Glycol ◽  
Propylene Carbonate ◽  
Reaction Temperature ◽  
Reaction Conditions ◽  
Lead Carbonate ◽  
Synthetic Process ◽  
Metal Carbonates ◽  
Optimal Reaction ◽  
Mixed Carbonate

A series of single-metal carbonates and Pb-Zn mixed-metal carbonates were prepared as catalysts for alcoholysis of urea with 1,2-propylene glycol (PG) for the synthesis of propylene carbonate (PC). The mixed carbonates all show much better catalytic activities than the single carbonates, arising from a strong synergistic effect between the two crystalline phases, hydrozincite and lead carbonate. The mixed carbonate with Pb/Zn=1:2 gives the highest yield of PC, followed by the mixed carbonate with Pb/Zn=1:3. Furthermore, Taguchi method was used to optimize the synthetic process for improving the yield of PC. It is shown that the reaction temperature is the most significant factor affecting the yield of PC, followed by the reaction time, and that the optimal reaction conditions are the reaction time at 5 hours, the reaction temperature at 180 oC and the catalyst amount at 1.8 wt%, resulting in the highest PC yield of 96.3%.

Membrane transport systems. II. Transport of alkali metal ions against their concentration gradients

1981 ◽  
Vol 59 (12) ◽  
pp. 1734-1744 ◽  
Author(s):  
Thomas M. Fyles ◽  
Virginia A. Malik-Diemer ◽  
Dennis M. Whitfield
Keyword(s):  
Alkali Metal ◽  
Metal Ions ◽  
Metal Ion ◽  
Complex Function ◽  
Membrane System ◽  
Ion Concentration ◽  
Transport Systems ◽  
Alkali Metal Ions ◽  
Concentration Gradients ◽  
Membrane Transport Systems

An artificial membrane system based on a series of macrocyclic polyether carriers (crown ethers) is described. Under the influence of a proton gradient the carriers move alkali metal ions from basic to acidic solution through a chloroform membrane phase. Transport occurs against the concentration gradient of the transported ion as a result of a coupled counterflow of protons. Different transport behaviors are observed depending upon the metal ion concentration. At high metal ion concentration the amount transported is a linear function of time; at lower metal ion concentration the amount transported is a complex function of time which may be described as the result of a pair of consecutive first order processes. Effects of metal ion, carrier, and proton concentration on transport rate are considered. The rate increases with increasing metal ion or carrier concentration but is essentially independent of the pH of either aqueous phase. Increased lipophilicity of the carrier also results in a rate increase. Carriers derived from 18-crown-6 transport potassium selectively and all ions more rapidly than 15-crown-5 derivatives which are, however, selective for sodium. The overall efficiency of the system is discussed in terms of competing "leak" reactions, either of cations from the basic phase or of anions from the acidic phase.

Removal of heavy metal ion from synthetic wastewater using spent tea waste powder

2021 ◽  
pp. 24-38
Author(s):  
Devyanshu Sachdev ◽  
Shyam Sunder Mishra ◽  
Srinivas Tadepalli
Keyword(s):  
Metal Ion ◽  
Traditional Approach ◽  
Operating Conditions ◽  
Ion Concentration ◽  
Metal Particles ◽  
Synthetic Wastewater ◽  
Batch Adsorption ◽  
Toxic Heavy Metals ◽  
Copper Solution ◽  
Tea Waste

The current work centres around on the expulsion of toxic heavy metals from mechanical effluents through the cycle of adsorption. This traditional approach is expensive, henceforth the utilization of ease, bountiful naturally neighbourly bio sorbents must be utilized. Adsorption conduct of copper and lead from waste water has been researched in this paper utilizing adsorbent like used tea powder waste. Copper and lead are profoundly harmful metal particles and considered as the need contamination delivered from different chemical ventures electroplating, blending exercises, smelting, battery manufacture etc. The effluents have been unnecessarily delivered into the climate because of expeditious industrialization and have made a worldwide concern. Hence, they should be taken out before release. In current paper, the trial results did in batch adsorption measure utilizing the treated waste tea powder with engineered test arranged in the test center were tried and introduced. The different boundaries, for example, solution’s pH, initial metal ion concentration, temperature and adsorbent dosage on the adsorption of Cu and Pb were considered. The greatest evacuation of Copper was above (at pH 5) 90% was observed using used tea waste powder at 100 ppm Copper solution. The removal of lead was above 85% (at pH 5) was respectively observed at the same operating conditions.

Sign in / Sign up

Export Citation Format

Share Document