Magnetoelectric properties in bulk and layered composites

2015 ◽  
Vol 32 (3) ◽  
pp. 110-114 ◽  
Author(s):  
Piotr Guzdek ◽  
Marek Wzorek
Keyword(s):  
Polyvinylidene Fluoride ◽  
Magnetoelectric Effect ◽  
Materials Science ◽  
Functional Materials ◽  
Solid State Reaction Method ◽  
Ceramic Composites ◽  
Sem Analysis ◽  
Content Type ◽  
Magnetoelectric Composites ◽  
Magnetoelectric Properties

Purpose – The purpose of the paper was to present a comparative study on the microstructure and magnetoelectric effect of new magnetoelectric composites based on TbFe2 compound and Ni0.3Zn0.62Cu0.08Fe2O4, CoFe2O4 ferrites as a magnetostrictive phase, Pb(Fe1/2Ta1/2)O3 (PFT), Pb(Fe1/2Nb1/2)O3 relaxors as a ferroelectric phase and polyvinylidene fluoride (PVDF) as piezoelectric phase. Design/methodology/approach – The ceramic components of composites were prepared by the standard solid-state reaction method. The intermetallic compound TbFe2 was prepared with an arc melting system with a contact-less ignition in a high purity argon atmosphere. The metal – ceramic – polymer composites were prepared in a container in which powder of PVDF were dissolved in N,N-dimethylformamide with continuous mixing and at the controlled temperature. Ceramic composites were prepared as bulk samples and multilayer tape cast and co-sintered laminates. The microstructure of the composites was investigated using scanning electron microscopy (SEM). The magnetoelectric effect of the composites was evaluated at room temperature by means of the dynamic lock-in method. Findings – SEM analysis revealed a dense, fine-grained microstructure and uniform distribution of the metallic, ferrite and relaxor grains in the bulk composites. The SEM image for multilayer composite illustrates the lack of cracks or delaminations at the phase boundaries between the well-sintered ferrite and relaxor layers. For all studied composites, the magnetoelectric coefficients at a lower magnetic field increase, reaches a maximum and then decreases. Originality/value – The progress in electronic technology is directly linked to advances made in materials science. Exploring and characterizing new materials with interesting magnetoelectric properties, in the rapidly growing field of functional materials, is an important task. The paper reports on processing, microstructure and magnetoelectric properties of novel magnetoelectric composites.

A glance on rare earth oxides: importance, reserves, demand, applications, critical uncertainties, global economy, and zeta potential characterization

2020 ◽  
Vol 05 ◽  
Author(s):  
Silas Santos ◽  
Orlando Rodrigues ◽  
Letícia Campos
Keyword(s):  
Rare Earth ◽  
Zeta Potential ◽  
Sample Preparation ◽  
Rare Earths ◽  
Smart Materials ◽  
Global Economy ◽  
Materials Science ◽  
Functional Materials ◽  
Rare Earth Oxides ◽  
Interparticle Forces

Background: Innovation mission in materials science requires new approaches to form functional materials, wherein the concept of its formation begins in nano/micro scale. Rare earth oxides with general form (RE2O3; RE from La to Lu, including Sc and Y) exhibit particular proprieties, being used in a vast field of applications with high technological content since agriculture to astronomy. Despite of their applicability, there is a lack of studies on surface chemistry of rare earth oxides. Zeta potential determination provides key parameters to form smart materials by controlling interparticle forces, as well as their evolution during processing. This paper reports a study on zeta potential with emphasis for rare earth oxide nanoparticles. A brief overview on rare earths, as well as zeta potential, including sample preparation, measurement parameters, and the most common mistakes during this evaluation are reported. Methods: A brief overview on rare earths, including zeta potential, and interparticle forces are presented. A practical study on zeta potential of rare earth oxides - RE2O3 (RE as Y, Dy, Tm, Eu, and Ce) in aqueous media is reported. Moreover, sample preparation, measurement parameters, and common mistakes during this evaluation are discussed. Results: Potential zeta values depend on particle characteristics such as size, shape, density, and surface area. Besides, preparation of samples which involves electrolyte concentration and time for homogenization of suspensions are extremely valuable to get suitable results. Conclusion: Zeta potential evaluation provides key parameters to produce smart materials seeing that interparticle forces can be controlled. Even though zeta potential characterization is mature, investigations on rare earth oxides are very scarce. Therefore, this innovative paper is a valuable contribution on this field.

scholarly journals Metal Nano/Microparticles for Bioapplications

2021 ◽  
Vol 22 (9) ◽  
pp. 4543
Author(s):  
Xuan-Hung Pham ◽  
Seung-min Park ◽  
Bong-Hyun Jun
Keyword(s):  
Materials Science ◽  
Functional Materials ◽  
Science And Engineering ◽  
Micro Particles ◽  
Materials Science And Engineering

Nano/micro particles are considered to be the most valuable and important functional materials in the field of materials science and engineering [...]

scholarly journals In Vitro Effect of Replicated Porous Polymeric Nano-MicroStructured Biointerfaces Characteristics on Macrophages Behavior

Nanomaterials ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1913
Author(s):  
Luminita Nicoleta Dumitrescu ◽  
Madalina Icriverzi ◽  
Anca Bonciu ◽  
Anca Roșeanu ◽  
Antoniu Moldovan ◽  
...  
Keyword(s):  
Inflammatory Response ◽  
Photoelectron Spectroscopy ◽  
Polyvinylidene Fluoride ◽  
Surface Characteristics ◽  
Sem Analysis ◽  
Chemical Structures ◽  
Microstructured Surface ◽  
Inflammatory Conditions ◽  
Vitro Effect

In the last decades, optimizing implant properties in terms of materials and biointerface characteristics represents one of the main quests in biomedical research. Modifying and engineering polyvinylidene fluoride (PVDF) as scaffolds becomes more and more attractive to multiples areas of bio-applications (e.g., bone or cochlear implants). Nevertheless, the acceptance of an implant is affected by its inflammatory potency caused by surface-induced modification. Therefore, in this work, three types of nano-micro squared wells like PVDF structures (i.e., reversed pyramidal shape with depths from 0.8 to 2.5 microns) were obtained by replication, and the influence of their characteristics on the inflammatory response of human macrophages was investigated in vitro. FTIR and X-ray photoelectron spectroscopy analysis confirmed the maintaining chemical structures of the replicated surfaces, while the topographical surface characteristics were evaluated by AFM and SEM analysis. Contact angle and surface energy analysis indicated a modification from superhydrophobicity of casted materials to moderate hydrophobicity based on the structure’s depth change. The effects induced by PVDF casted and micron-sized reversed pyramidal replicas on macrophages behavior were evaluated in normal and inflammatory conditions (lipopolysaccharide treatment) using colorimetric, microscopy, and ELISA methods. Our results demonstrate that the depth of the microstructured surface affects the activity of macrophages and that the modification of topography could influence both the hydrophobicity of the surface and the inflammatory response.

Theoretical investigation of magnetoelectric effect in multilayer magnetoelectric composites

2015 ◽  
Vol 119 ◽  
pp. 738-748 ◽  
Author(s):  
Guo-Liang Yu ◽  
Huai-Wu Zhang ◽  
Fei-Ming Bai ◽  
Yuan-Xun Li ◽  
Jie Li
Keyword(s):  
Theoretical Investigation ◽  
Magnetoelectric Effect ◽  
Magnetoelectric Composites

Tribological characteristics of AA8090-WC-ZrC metal matrix composites prepared by stir casting process for Aerospace applications

2021 ◽  
Vol 73 (6) ◽  
pp. 980-985
Author(s):  
Kalaiyarasan A ◽  
Sundaram S ◽  
Gunasekaran K ◽  
Bensam Raj J.
Keyword(s):  
Metal Matrix ◽  
Materials Science ◽  
Scientific Information ◽  
High Hardness ◽  
Hardness Test ◽  
Casting Process ◽  
Stir Casting ◽  
Hybrid Particles ◽  
Content Type ◽  
The Impact

Purpose Aerospace field is demanding a material with superior strength and high resistance against wear, tear and corrosion. The current study aimed to develop a new material with high performance to be applicable in aerospace field Design/methodology/approach A metal matrix composite AA8090-WC-ZrC was fabricated using stir casting method and its tribological behavior was investigated. Totally, five composites viz. AA/Z, AA/W, AA/WZ (1:3), AA/WZ (1:1) & AA/WZ (3:1) were prepared. Micro hardness, tensile and wear study were performed on the fabricated composites and the results were compared with AA8090 alloy Findings Vickers hardness test resulted that the AA/W composite showed the higher hardness value of 160 HB compared to other materials due to the reinforcing effect of WC particles with high hardness. Tensile test reported that the AA/W composite displayed the maximum tensile strength of 502 MPa owing to the creation of more dislocation density. Further, wear study showed that the AA/W composite exhibited the least wear rate of 0.0011 mm3/m because of the more resisting force offered by the WC particles. Furthermore, the AA/W composite showed the slightest mass loss of 0.0028 g and lower COF value of 0.31 due to the hinder effect of WC particle to the movement of atoms in AA8090 alloy Originality/value This work is original in the field of aerospace engineering and materials science which deals with the fabrication of AA8090 alloy with the reinforcement particles such as tungsten carbide and zirconium carbide. The impact of the combination of hybrid particles and their volume fractions on the tribological properties has been investigated in this work. This work would provide new scientific information to society.

Tribological and electrical behavior of Cu-based composites with addition of Ti-doped NbSe2 nanoplatelets

2018 ◽  
Vol 70 (3) ◽  
pp. 560-567 ◽  
Author(s):  
Jian Feng Li ◽  
Qin Shi ◽  
HeJun Zhu ◽  
ChenYu Huang ◽  
Shuai Zhang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Solid State ◽  
Friction Coefficient ◽  
Electrical Properties ◽  
Tribological Properties ◽  
Solid State Reaction ◽  
Electrical Contact ◽  
Solid State Reaction Method ◽  
Content Type ◽  
Reaction Method

Purpose This paper aims to clarify the size and morphology of transition metal dichalcogenides has an impact on lubrication performance of Cu-based composites. This study is intended to show that Cu-based electrical contact materials containing Nb0.91Ti0.09Se2 have better electrical and tribological properties than those containing NbSe2. The tribological properties of Cu-based with different Ti-dopped NbSe2 content were also discussed. Design/methodology/approach The NbSe2 and Nb0.91Ti0.09Se2 particles were fabricated by thermal solid state reaction method. The powder metallurgy technique was used to fabricate composites with varying Nb0.91Ti0.09Se2 mass fraction. The phase composition of Cu-based composites was identified by X-ray diffraction, and the morphology of NbSe2/Nb0.91Ti0.09Se2 and the worn surface of composites were characterized by scanning electron microscopy and transmission electron microscopy. In addition, the tribological properties of composites were appraised using a ball-on-disk multi-functional tribometer. The data of friction coefficient and resistivity were analyzed and the corresponding conclusion was drawn. Findings In comparison with the pure copper, Cu-based composites containing Nb0.91Ti0.09Se2/NbSe2 had a lower friction coefficient, illustrating the Nb0.91Ti0.09Se2 with nano-size particles prepared in this work is a perfect choice for the fabrication of excellent electrical contact composites. Compared to composites with NbSe2, composites containing Nb0.91Ti0.09Se2 have better tribological and electrical properties. Research limitations/implications Because of the use of thermal solid state reaction method, the size of NbSe2 and Nb0.91Ti0.09Se2 is relatively large. Therefore, the fabrication of finer particles of Nb0.91Ti0.09Se2 is encouraged. Originality/value In this paper, the authors discuss the tribological and electrical properties of Cu-based composites, and the value of optimum obtained as Nb0.91Ti0.09Se2 content is 15 Wt.%.

Characterization and applicability of Sm0.9Sr0.1CoO3-δ in oxygen sensors

2014 ◽  
Vol 31 (3) ◽  
pp. 154-157 ◽  
Author(s):  
Katarina Cvejin ◽  
Libu Manjakkal ◽  
Jan Kulawik ◽  
Krzysztof Zaraska ◽  
Dorota Szwagierczak
Keyword(s):  
Seebeck Coefficient ◽  
Thick Film ◽  
Bulk Sample ◽  
Solid State Reaction Method ◽  
Oxygen Sensors ◽  
Potentiometric Sensors ◽  
X Ray Diffraction ◽  
Content Type ◽  
Thermal Analyzer ◽  
Perovskite Material

Purpose – This paper aims to investigate different properties of synthesized perovskite Sm0.9Sr0.1CoO3-δ and its potential for application in potentiometric oxygen sensors. Design/methodology/approach – The powder was obtained through solid-state reaction method and characterized by thermogravimetric/differential thermal analyzer and X-ray diffraction. It was used for both making a paste and pressing into rods for sintering. The prepared paste was deposited on alumina and yttria-stabilized zirconia substrates, by screen printing. Thick film conductivity, bulk conductivity and Seebeck coefficient of sintered rods were measured as a function of temperature. An oxygen concentration cell was fabricated with the screen-printed perovskite material as electrodes. Findings – Electrical conductivity of the bulk sample and thick film increases with the increase in temperature, showing semiconductor-like behavior, which is also indicated by relatively high values of the measured Seebeck coefficient. Estimated values of the activation energy for conduction are found to be of the same magnitude as those reported in the literature for similar composition. An investigation of Nernstian behavior of the fabricated cell confirmed that Sm0.9Sr0.1CoO3-δ is a promising material for application in oxygen potentiometric sensors. Originality/value – Gas sensor research is focused on the development of new sensitive materials. Although there is scarce information on SmCoO3-δ in the literature, it is mostly investigated for fuel cell applications. Results of this study imply that Sr-doped SmCoO3-δ is a good candidate material for oxygen potentiometric sensor.

Enhancing the mechanical properties of bismaleimide resin with montmorillonite modified by two intercalators (amino-terminated polyoxypropylene and octadecyl trimethyl ammonium chloride)

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Yufei Chen ◽  
Hui Zhao ◽  
Yulong Liu ◽  
Hongyue CHU
Keyword(s):  
Mechanical Properties ◽  
Bisphenol A ◽  
Ammonium Chloride ◽  
Functional Materials ◽  
Crosslinking Density ◽  
Trimethyl Ammonium Chloride ◽  
Sem Images ◽  
Bismaleimide Resin ◽  
Content Type ◽  
The Matrix

Purpose Bismaleimide (BMI) is a kind of thermosetting resin and its application is usually limited by low toughness. In this paper, two kinds of reinforcement intercalator amino-terminated polyoxypropylene (POP) and octadecyl trimethyl ammonium chloride (OTAC) were designed and synthesized to toughen BMI resin and the toughening effect was compared and analyzed. The purpose of this paper is to toughen BMI resin and analyze the toughening effect of two reinforcements intercalator amino-terminated polyoxypropylene (POP) and octadecyl trimethyl ammonium chloride (OTAC). Design/methodology/approach Sodium-based montmorillonite (Na-MMT) was modified by POP and OTAC, and the ion-exchange reaction obtained organic montmorillonite (POP-MMT and OTAC-MMT). The polymer matrix (MBAE) was synthesized, in which 4,4’-diamino diphenyl methane BMI was used as the monomer and 3,3’-diallyl bisphenol A and bisphenol A diallyl ether were used as active diluents. And then, POP-MMT/MBAE and OTAC-MMT/MBAE composites were prepared using MBAE as matrix and POP-MMT or OTAC-MMT as reinforcement. The Fourier-transform infrared, X-ray diffraction and scanning electron microscope (SEM) of the filler and microstructure and mechanical properties of the composite were characterized to the better reinforcement. Findings POP-MMT and OTAC-MMT enhanced BMI-cured products’ toughness by generating microcracks in the polymer to absorb more fracture energy. Meanwhile, POP-MMT and OTAC-MMT were the main stress components and the enhancement of the interface interaction was beneficial to transfer the external force from the matrix to the reinforcement and improved the mechanical properties of the composite. Furthermore, with the intercalation rate increasing, the compatibility of the two phases was increased and the performance of MBAE was also elevated. Research limitations/implications BMI is generally used as aerospace structural materials, functional materials, impregnating paint and other fields. However, high crosslinking density leads to moulding material’s brittleness and limits a wider range of applications. Therefore, it has become an urgent priority to explore and improve the mechanical properties of BMI resin. Originality/value POP and OTAC have successfully intercalated Na-MMT layers to get POP-MMT and OTAC-MMT, and the interplanar crystal spacing and the intercalation rate were calculated, respectively. The results were corresponding with the SEM images of POP-MMT and OTAC-MMT. After that, the morphology of composites illustrated the compatibility was related to the intercalation rate. According to the mechanism of modified MMT toughening epoxy resin, when they were dispersed uniformly in the matrix, the composite’s mechanical properties had been significantly improved. Additionally, OTAC-MMT with a higher intercalation rate had better compatibility and interfacial force with the matrix, so that the mechanical properties of OTAC-MMT/MBAE were the best.

Multipurpose diffractometer for in situ X-ray crystallography of functional materials

2021 ◽  
Vol 54 (3) ◽  
Author(s):  
Semën Gorfman ◽  
David Spirito ◽  
Netanela Cohen ◽  
Peter Siffalovic ◽  
Peter Nadazdy ◽  
...  
Keyword(s):  
Electric Field ◽  
Materials Science ◽  
Functional Materials ◽  
X Ray Diffraction ◽  
Reciprocal Space Mapping ◽  
X Ray ◽  
X Ray Crystallography ◽  
Area Detector ◽  
Characterization Of Materials

Laboratory X-ray diffractometers play a crucial role in X-ray crystallography and materials science. Such instruments still vastly outnumber synchrotron facilities and are responsible for most of the X-ray characterization of materials around the world. The efforts to enhance the design and performance of in-house X-ray diffraction instruments benefit a broad research community. Here, the realization of a custom-built multipurpose four-circle diffractometer in the laboratory for X-ray crystallography of functional materials at Tel Aviv University, Israel, is reported. The instrument is equipped with a microfocus Cu-based X-ray source, collimating X-ray optics, four-bounce monochromator, four-circle goniometer, large (PILATUS3 R 1M) pixel area detector, analyser crystal and scintillating counter. It is suitable for a broad range of tasks in X-ray crystallography/structure analysis and materials science. All the relevant X-ray beam parameters (total flux, flux density, beam divergence, monochromaticity) are reported and several applications such as determination of the crystal orientation matrix and high-resolution reciprocal-space mapping are demonstrated. The diffractometer is suitable for measuring X-ray diffraction in situ under an external electric field, as demonstrated by the measurement of electric-field-dependent rocking curves of a quartz single crystal. The diffractometer can be used as an independent research instrument, but also as a training platform and for preparation for synchrotron experiments.

Sign in / Sign up

Export Citation Format

Share Document