Rheology effect and enhanced thermal conductivity of diamond/metakaolin geopolymer fabricated by direct ink writing

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Yushen Wang ◽  
Wei Xiong ◽  
Danna Tang ◽  
Liang Hao ◽  
Zheng Li ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Diamond Powder ◽  
Thermal Imager ◽  
Corrosion Properties ◽  
Content Type ◽  
Sensor Material ◽  
Direct Ink Writing ◽  
Diamond Particles ◽  
Before And After

Purpose Traditional simulation research of geological and similar engineering models, such as landslides or other natural disaster scenarios, usually focuses on the change of stress and the state of the model before and after destruction. However, the transition of the inner change is usually invisible. To optimize and make models more intelligent, this paper aims to propose a perceptible design to detect the internal temperature change transformed by other energy versions like stress or torsion. Design/methodology/approach In this paper, micron diamond particles were embedded in 3D printed geopolymers as a potential thermal sensor material to detect the inner heat change. The authors use synthetic micron diamond powder to reinforced the anti-corrosion properties and thermal conductivity of geopolymer and apply this novel geopolymer slurry in the direct ink writing (DIW) technique. Findings As a result, the addition of micron diamond powder can greatly influence the rheology of geopolymer slurry and make the geopolymer slurry extrudable and suitable for DIW by reducing the slope of the viscosity of this inorganic colloid. The heat transfer coefficient of the micron diamond (15 Wt.%)/geopolymer was 50% higher than the pure geopolymer, which could be detected by the infrared thermal imager. Besides, the addition of diamond particles also increased the porous rates of geopolymer. Originality/value In conclusion, DIW slurry deposition of micron diamond-embedded geopolymer (MDG) composites could be used to manufacture the multi-functional geological model for thermal imaging and defect detection, which need the characteristic of lightweight, isolation, heat transfer and wave absorption.

Effect of magnetic field-dependent thermal conductivity on natural convection of magnetic nanofluid inside a square enclosure

2019 ◽  
Vol 29 (4) ◽  
pp. 1466-1489 ◽  
Author(s):  
Mohammadhossein Hajiyan ◽  
Shohel Mahmud ◽  
Mohammad Biglarbegian ◽  
Hussein A. Abdullah ◽  
A. Chamkha
Keyword(s):  
Magnetic Field ◽  
Heat Transfer ◽  
Thermal Conductivity ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Hartmann Number ◽  
Magnetic Nanofluid ◽  
Content Type ◽  
Square Enclosure ◽  
Field Dependent

Purpose The purpose of this paper is to investigate the convective heat transfer of magnetic nanofluid (MNF) inside a square enclosure under uniform magnetic fields considering nonlinearity of magnetic field-dependent thermal conductivity. Design/methodology/approach The properties of the MNF (Fe3O4+kerosene) were described by polynomial functions of magnetic field-dependent thermal conductivity. The effect of the transverse magnetic field (0 < H < 105), Hartmann Number (0 < Ha < 60), Rayleigh number (10 <Ra <105) and the solid volume fraction (0 < φ < 4.7%) on the heat transfer performance inside the enclosed space was examined. Continuity, momentum and energy equations were solved using the finite element method. Findings The results show that the Nusselt number increases when the Rayleigh number increases. In contrast, the convective heat transfer rate decreases when the Hartmann number increases due to the strong magnetic field which suppresses the buoyancy force. Also, a significant improvement in the heat transfer rate is observed when the magnetic field is applied and φ = 4.7% (I = 11.90%, I = 16.73%, I = 10.07% and I = 12.70%). Research limitations/implications The present numerical study was carried out for a steady, laminar and two-dimensional flow inside the square enclosure. Also, properties of the MNF are assumed to be constant (except thermal conductivity) under magnetic field. Practical implications The results can be used in thermal storage and cooling of electronic devices such as lithium-ion batteries during charging and discharging processes. Originality/value The accuracy of results and heat transfer enhancement having magnetic field-field-dependent thermal conductivity are noticeable. The results can be used for different applications to improve the heat transfer rate and enhance the efficiency of a system.

Eulerian–Eulerian multi-phase RPI modeling of turbulent forced convective of boiling flow inside the tube with porous medium

2019 ◽  
Vol 30 (5) ◽  
pp. 2739-2757 ◽  
Author(s):  
Reza Azadbakhti ◽  
Farzad Pourfattah ◽  
Abolfazl Ahmadi ◽  
Omid Ali Akbari ◽  
Davood Toghraie
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Reynolds Number ◽  
Porous Medium ◽  
Flow Boiling ◽  
Rensselaer Polytechnic Institute ◽  
Content Type ◽  
Turbulent Flow Regime ◽  
High Reynolds ◽  
Multi Phase

Purpose The purpose of this study is simulation the flow boiling inside a tube in the turbulent flow regime for investigating the effect of using a porous medium in the boiling procedure. Design/methodology/approach To ensure the accuracy of the obtained numerical results, the presented results have been compared with the experimental results, and proper coincidence has been achieved. In this study, the phase change phenomenon of boiling has been modeled by using the Eulerian–Eulerian multi-phase Rensselaer Polytechnic Institute (RPI) wall boiling model. Findings The obtained results indicate using a porous medium in boiling process is very effective in a way that by using a porous medium inside the tub, the location of changing the liquid to the vapor and the creation of bubbles, changes. By increasing the thermal conductivity of porous medium, the onset of phase changing postpones, which causes the enhancement of heat transfer from the wall to the fluid. Generally, it can be said that using a porous medium in boiling flows, especially in flow with high Reynolds numbers, has a positive effect on heat transfer enhancement. Also, the obtained results revealed that by increasing Reynolds number, the created vapor phase along the tube decreases and by increasing Reynolds number, the Nusselt number enhances. Originality/value In present research, by using the computational fluid dynamics, the effect of using a porous medium in the forced boiling of water flow inside a tube has been investigated. The fluid boiling inside the tube has been simulated by using the multi-phase Eulerian RPI wall boiling model, and the effect of thermal conductivity of a porous medium and the Reynolds number on the flow properties, heat transfer and boiling procedure have been investigated.

Analysis of nanofluids as a means of thermal conductivity enhancement in heavy machineries

2014 ◽  
Vol 66 (2) ◽  
pp. 238-243 ◽  
Author(s):  
Ayush Jain ◽  
Imbesat Hassan Rizvi ◽  
Subrata Kumar Ghosh ◽  
P.S. Mukherjee
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Ethylene Glycol ◽  
Base Fluid ◽  
High Concentration ◽  
Content Type ◽  
Conductivity Enhancement ◽  
Heavy Machinery ◽  
Heat Transfer Fluids ◽  
Experimental Findings

Purpose – Nanofluids exhibit enhanced heat transfer characteristics and are expected to be the future heat transfer fluids particularly the lubricants and transmission fluids used in heavy machinery. For studying the heat transfer behaviour of the nanofluids, precise values of their thermal conductivity are required. For predicting the correct value of thermal conductivity of a nanofluid, mathematical models are necessary. In this paper, the effective thermal conductivity of various nanofluids has been reported by using both experimental and mathematical modelling. The paper aims to discuss these issues. Design/methodology/approach – Hamilton and Crosser equation was used for predicting the thermal conductivities of nanofluids, and the obtained values were compared with the experimental findings. Nanofluid studied in this paper are Al2O3 in base fluid water, Al2O3 in base fluid ethylene glycol, CuO in base fluid water, CuO in base fluid ethylene glycol, TiO2 in base fluid ethylene glycol. In addition, studies have been made on nanofluids with CuO and Al2O3 in base fluid SAE 30 particularly for heavy machinery applications. Findings – The study shows that increase in thermal conductivity of the nanofluid with particle concentration is in good agreement with that predicted by Hamilton and Crosser at typical lower concentrations. Research limitations/implications – It has been observed that deviation between experimental and theoretical results increases as the volume concentration of nanoparticles increases. Therefore, the mathematical model cannot be used for predicting thermal conductivity at high concentration values. Originality/value – Studies on nanoparticles with a standard mineral oil as base fluid have not been considered extensively as per the previous literatures available.

Dufour and Soret effects on Darcy-Forchheimer flow of second-grade fluid with the variable magnetic field and thermal conductivity

2020 ◽  
Vol 30 (9) ◽  
pp. 4331-4347 ◽  
Author(s):  
Ambreen A. Khan ◽  
S. Naeem ◽  
R. Ellahi ◽  
Sadiq M. Sait ◽  
K. Vafai
Keyword(s):  
Magnetic Field ◽  
Heat Transfer ◽  
Thermal Conductivity ◽  
Variable Magnetic Field ◽  
Second Grade ◽  
Second Grade Fluid ◽  
Content Type ◽  
Grade Fluid ◽  
The Impact ◽  
Forchheimer Flow

Purpose This study aims to investigate the effect of two-dimensional Darcy-Forchheimer flow over second-grade fluid with linear stretching. Heat transfer through convective boundary conditions is taken into account. Design/methodology/approach Nonlinear coupled governing equations are tackled with a homotopy algorithm, while for numerical computation the computer software package BVPh 2.0 is used. The convergence analysis is also presented for the validation of analytical and numerical results. Findings Valuation for the impact of key parameters such as variable thermal conductivity, Dufour and Soret effects and variable magnetic field in an electrically conducted fluid on the velocity, concentration and temperature profiles are graphically illustrated. It is observed from the results that temperature distribution rises by Dufour number whereas concentration distribution rises by Soret number. The Forchheimer number and porosity parameter raise the skin friction coefficient. The permeable medium has a vital impact and can help in reining the rate of heat transfer. Practical implications The permeable medium has a vital impact and can help in reining the rate of heat transfer. Originality/value To the best of the authors’ knowledge, this study is reported for the first time.

MHD slip flow and convective heat transfer due to a moving plate with effects of variable viscosity and thermal conductivity

2020 ◽  
Vol 16 (5) ◽  
pp. 991-1018
Author(s):  
Mahantesh M. Nandeppanavar ◽  
M.C. Kemparaju ◽  
R. Madhusudhan ◽  
S. Vaishali
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Boundary Layer ◽  
Differential Equations ◽  
Radiation Effects ◽  
Variable Viscosity ◽  
Heat Transfer Analysis ◽  
Concentration Profiles ◽  
Moving Plate ◽  
Content Type

PurposeThe steady two-dimensional laminar boundary layer flow, heat and mass transfer over a flat plate with convective surface heat flux was considered. The governing nonlinear partial differential equations were transformed into a system of nonlinear ordinary differential equations and then solved numerically by Runge–Kutta method with the most efficient shooting technique. Then, the effect of variable viscosity and variable thermal conductivity on the fluid flow with thermal radiation effects and viscous dissipation was studied. Velocity, temperature and concentration profiles respectively were plotted for various values of pertinent parameters. It was found that the momentum slip acts as a boost for enhancement of the velocity profile in the boundary layer region, whereas temperature and concentration profiles decelerate with the momentum slip.Design/methodology/approachNumerical Solution is applied to find the solution of the boundary value problem.FindingsVelocity, heat transfer analysis is done with comparing earlier results for some standard cases.Originality/value100

Effective heat conductivity of Honeycomb (porous) composite panel

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Cletus Matthew Magoda ◽  
Jasson Gryzagoridis ◽  
Kant Kanyarusoke
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Composite Material ◽  
Thermal Properties ◽  
Heat Conductivity ◽  
Composite Panel ◽  
Porous Composite ◽  
Content Type ◽  
One Dimensional ◽  
Coefficient Of Thermal Conductivity

Purpose The purpose of this paper is to validate an assumption of what to use as an effective (steady state) heat transfer coefficient of thermal conductivity for the honeycomb core sandwiched by Fiberglass face sheets composite. A one-dimensional model based on Fourier law is developed. The results are validated experimentally. Design/methodology/approach The results were obtained from the one-dimensional mathematical model of an overall or effective heat conductivity of the Honeycomb composite panel. These results were validated experimentally by applying heat flux on the specimen under controlled environment. The surface temperatures at different voltages were recorded and analysed. The skin of the sandwich composite material used in the investigation was Fiberglass sheet with a thickness of 0.5 mm at the bottom and 1.0 mm at the top surface. Both skins have a stacking sequence of zero degrees. Due to the presence of air cells in the core (Honeycomb), the model considers the conduction, convection and radiation heat transfer, across the thickness of the panel, combined as an effective conduction mode, whose value may be predicted by using the coefficient of thermal conductivity of the air based on the average temperature difference between the two skins. The experimental results for the heat transfer through the thickness of the panel provide validation of this assumption/prediction. Both infrared thermography and conventional temperature measurement techniques (thermocouples) were used to collect the data. Findings The heat transfer experiment and mathematical modeling were conducted. The data obtained were analyzed, and it was found that the effective thermal conductivity was temperature-dependent as expected. The effective thermal conductivity of the honeycomb panel was close to that of air, and its value could be predicted if the panel surface temperatures were known. It was also found that as temperature raised the variation between experimental and predicted effective air conduction raised up. This is because there was an increase in molecular diffusion and vibration. Therefore, the convection heat transfer increased at high temperatures and the air became an insulator. Originality/value Honeycomb composite panels have excellent physical and thermal properties that influence their performance. This study provides an appropriate method in determining thermal conductivity, which is one of the critical thermal properties of porous composite material. This paper also gives useful and practical data to industries that use or manufacture honeycomb composite panels.

Mixed convection squeezing three-dimensional flow in a rotating channel filled with nanofluid

2016 ◽  
Vol 26 (5) ◽  
pp. 1460-1485 ◽  
Author(s):  
B Mahanthesh ◽  
B J Gireesha ◽  
R S R Gorla
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Differential Equations ◽  
Mixed Convection ◽  
Three Dimensional ◽  
Vertical Channel ◽  
Three Dimensional Flow ◽  
Content Type ◽  
Dimensional Flow ◽  
Rotating Channel

Purpose – The purpose of this paper is to numerically solve the problem of an unsteady squeezing three-dimensional flow and heat transfer of a nanofluid in rotating vertical channel of stretching left plane. The fluid is assumed to be Newtonian, incompressible and electrically conducting embedded with nanoparticles. Effect of internal heat generation/ absorption is also considered in energy equation. Four different types of nanoparticles are considered, namely, copper (Cu), alumina (Al2O3), silver (Ag) and titanium oxide (TiO2) with the base fluid as water. Maxwell-Garnetts and Brinkman models are, respectively, employed to calculate the effective thermal conductivity and viscosity of the nanofluid. Design/methodology/approach – Using suitable similarity transformations, the governing partial differential equations are transformed into set of ordinary differential equations. Resultant equations have been solved numerically using Runge-Kutta-Fehlberg fourth fifth order method for different values of the governing parameters. Effects of pertinent parameters on normal, axial and tangential components of velocity and temperature distributions are presented through graphs and discussed in detail. Further, effects of nanoparticle volume fraction, squeezing parameter, suction/injection parameter and heat source/sink parameter on skin friction and local Nusselt number profiles for different nanoparticles are presented in tables and analyzed. Findings – Squeezing effect enhances the temperature field and consequently reduces the heat transfer rate. Large values of mixed convection parameter showed a significant effect on velocity components. Also, in many heat transfer applications, nanofluids are potentially useful because of their novel properties. They exhibit high-thermal conductivity compared to the base fluids. Further, squeezing and rotation effects are desirable in control the heat transfer. Originality/value – Three-dimensional mixed convection flows over in rotating vertical channel filled with nanofluid are very rare in the literature. Mixed convection squeezing three-dimensional flow in a rotating channel filled with nanofluid is first time investigated.

Upward and downward conjugate mixed convection heat transfer in a partially porous cavity

2016 ◽  
Vol 26 (1) ◽  
pp. 159-188 ◽  
Author(s):  
Abderrahim Bourouis ◽  
Abdeslam Omara ◽  
Said Abboudi
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Mixed Convection ◽  
Transfer Rate ◽  
Vertical Wall ◽  
Thermal Conductivity Ratio ◽  
Conductivity Ratio ◽  
Content Type ◽  
Moving Wall ◽  
The Right

Purpose – The purpose of this paper is to provide a numerical study of conjugate heat transfer by mixed convection and conduction in a lid-driven enclosure with thick vertical porous layer. The effect of the relevant parameters: Richardson number (Ri=0.1, 1, 10) and thermal conductivity ratio (Rk=0.1, 1, 10, 100) are investigated. Design/methodology/approach – The studied system is a two dimensional lid-driven enclosure with thick vertical porous layer. The left vertical wall of the enclosure is allowed to move in its own plane at a constant velocity. The enclosure is heated from the right vertical wall isothermally. The left and the right vertical walls are isothermal but temperature of the outside of the right vertical wall is higher than that of the left vertical wall. Horizontal walls are insulated. The governing equations are solved by finite volume method and the SIMPLE algorithm. Findings – From the finding results, it is observed that: for the two studied cases, heat transfer rate along the hot wall is a decreasing function of thermal conductivity ratio irrespective of Richardson numbers contrary to the heat transfer rate along the fluid-porous layer interface which is an increasing function of thermal conductivity ratio. At forced convection dominant regime, the difference between heat transfer rate for upward and downward moving wall is insensitive to the thermal conductivity ratio. For downward moving wall, average Nusselt number is higher than that of upward moving wall. Practical implications – Some applications: building applications, furnace design, nuclear reactors, air solar collectors. Originality/value – From the bibliographic work and the authors’ knowledge, the conjugate mixed convection in lid-driven partially porous enclosures has not yet been investigated which motivates the present work that represent a continuation of the preceding investigations.

scholarly journals Numerical study of heat transfer in 90° bend tube by AI2O3 nano fluids using fluid injection

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Hadi Mahdizadeh ◽  
Nor Mariah Adam
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Reynolds Number ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Volume Fraction ◽  
Fluid Injection ◽  
Content Type ◽  
Nano Fluid ◽  
The Impact

Purpose This paper aims to investigate increasing heat transfer in bend tube 90° by fluid injection using nano fluid flow that was performed by expending varying Reynolds number. This paper studies the increased heat transfer in the bent tube that used some parameters to examine the effects of volume fraction, nanoparticle diameter, fluid injection, Reynolds number on heat transfer and flow in a bend pipe. Design/methodology/approach Designing curved tubes increases the thermal conductivity amount between fluid and wall. It is used the finite volume method and simple algorithms to solve the conservation equations of mass, momentum and energy. The results showed that the nanoparticles used in bent tube transfusion increase the heat transfer performance by increasing the volume fraction; it has a direct impact on enhancing the heat transfer coefficient. Findings Heat transfer coefficient enhanced 1.5% when volume fraction increased from 2 % to 6%, the. It is due to the impact of nanoparticles on the thermal conductivity of the fluid. The fluid is injected into the boundary layer flow due to jamming that enhances heat transfer. Curved lines used create a centrifugal force due to the bending and lack of development that increase the heat transfer. Originality/value This study has investigated the effect of injection of water into a 90° bend before and after the bend. Specific objectives are to analyze effect of injection on heat transfer of bend tube and pressure drop, evaluate best performance of mixing injection and bend in different positions and analyze effect of nano fluid volume fraction on injection.

Natural convection of nanofluids in a cavity: criteria for enhancement of nanofluids

2017 ◽  
Vol 27 (7) ◽  
pp. 1504-1534 ◽  
Author(s):  
M. Sabour ◽  
Mohammad Ghalambaz ◽  
Ali Chamkha
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Dynamic Viscosity ◽  
Base Fluid ◽  
Convection Heat Transfer ◽  
Governing Equations ◽  
Content Type ◽  
Separation Line ◽  
Working Temperature ◽  
Dimensional Parameters

Purpose The purpose of this study is to theoretically analyze the laminar free convection heat transfer of nanofluids in a square cavity. The sidewalls of the cavity are subject to temperature difference, whereas the bottom and top are insulated. Based on the available experimental results in the literature, two new non-dimensional parameters, namely, the thermal conductivity parameter (Nc) and dynamic viscosity parameter (Nv) are introduced. These parameters indicate the augmentation of the thermal conductivity and dynamic viscosity of the nanofluid by dispersing nanoparticles. Design/methodology/approach The governing equations are transformed into non-dimensional form using the thermo-physical properties of the base fluid. The obtained governing equations are solved numerically using the finite element method. The results are reported for the general non-dimensional form of the problem as well as case studies in the form of isotherms, streamlines and the graphs of the average Nusselt number. Using the concept of Nc and Nv, some criteria for convective enhancement of nanofluids are proposed. As practical cases, the effect of the size of nanoparticles, the shape of nanoparticles, the type of nanoparticles, the type of base fluids and working temperature on the enhancement of heat transfer are analyzed. Findings The results show that the increase of the magnitude of the Rayleigh number increases of the efficiency of using nanofluids. The type of nanoparticles and the type of the base fluid significantly affects the enhancement of using nanofluids. Some practical cases are found, in which utilizing nanoparticles in the base fluid results in deterioration of the heat transfer. The working temperature of the nanofluid is very crucial issue. The increase of the working temperature of the nanofluid decreases the convective heat transfer, which limits the capability of nanofluids in decreasing the size of the thermal systems. Originality/value In the present study, a separation line based on two non-dimensional parameters (i.e. Nc and Nv) are introduced. The separation line demonstrates a boundary between augmentation and deterioration of heat transfer by using nanoparticles. Indeed, by utilizing the separation lines, the convective enhancement of using nanofluid with a specified Nc and Nv can be simply estimated.

Sign in / Sign up

Export Citation Format

Share Document