Effect of growth media on natural starter culture composition and performance evaluated with a polyphasic approach

2018 ◽  
Vol 72 (1) ◽  
pp. 152-158 ◽  
Author(s):  
Luigi Chessa ◽  
Antonio Paba ◽  
Elisabetta Daga ◽  
Roberta Comunian
Keyword(s):  
Starter Culture ◽  
Polyphasic Approach ◽  
Growth Media ◽  
And Performance

Upgrading of facultative ponds to treat a toxic organic wastewater

1995 ◽  
Vol 31 (12) ◽  
pp. 201-210 ◽  
Author(s):  
C. Polprasert ◽  
S. Sookhanich
Keyword(s):  
High Strength ◽  
Pond Water ◽  
Superior Performance ◽  
Growth Media ◽  
Phenol Removal ◽  
Waste Stabilization Ponds ◽  
Attached Growth ◽  
Waste Stabilization ◽  
Removal Efficiencies ◽  
And Performance

This study investigated the efficiency and performance of attached-growth waste stabilization ponds (AGWSP) treating a high-strength phenolic wastewater. The experiments employed 4 laboratory-scale pond units installed with an artificial attached-growth media. A control pond unit without attached-growth media (or WSP) was run in parallel for data comparison. The experimental results revealed that the AGWSP units could remove about 99, 50, 45 and 28% of phenol when operated at influent phenol concentrations of 500, 1000, 1500 and 2000 mg/l (corresponding to organic loading rates (OLR) of 180, 360, 540 and 720 kg COD/(ha.day), respectively); these removal efficiencies were consistently higher than those observed in the WSP unit. The influent phenol concentrations of 1000-2000 mg/l resulted in some toxic effects and over loading to the pond system, causing the phenol removal efficiencies to decrease. The amount of phenol loss from the pond water through volatilization was found to be approximately 10%. A relationship between phenol removal rates (excluding volatilization) and phenol dosages to the AGWSP was developed. The superior performance of the AGWSP over the WSP appeared to be due to the biofilm biomass growing on the attached-growth media surface, resulting in increased potential biomass in the pond water.

scholarly journals Lactobacillus kefiranofaciens: From Isolation and Taxonomy to Probiotic Properties and Applications

2021 ◽  
Vol 9 (10) ◽  
pp. 2158
Author(s):  
Marina Georgalaki ◽  
Georgia Zoumpopoulou ◽  
Rania Anastasiou ◽  
Maria Kazou ◽  
Effie Tsakalidou
Keyword(s):  
Bacterial Species ◽  
Starter Culture ◽  
Blood Lipid ◽  
Growth Conditions ◽  
Water Soluble ◽  
Growth Media ◽  
Rrna Gene ◽  
Probiotic Properties ◽  
Kefir Grain ◽  
Health Promoting

One of the main lactic acid bacterial species found in the kefir grain ecosystem worldwide is Lactobacillus kefiranofaciens, exhibiting strong auto-aggregation capacity and, therefore, being involved in the mechanism of grain formation. Its occurrence and dominance in kefir grains of various types of milk and geographical origins have been verified by culture-dependent and independent approaches using multiple growth media and regions of the 16S rRNA gene, respectively, highlighting the importance of their combination for its taxonomic identification. L. kefiranofaciens comprises two subspecies, namely kefiranofaciens and kefirgranum, but only the first one is responsible for the production of kefiran, the water-soluble polysaccharide, which is a basic component of the kefir grain and famous for its technological as well as health-promoting properties. L. kefiranofaciens, although very demanding concerning its growth conditions, can be involved in mechanisms affecting intestinal health, immunomodulation, control of blood lipid levels, hypertension, antimicrobial action, and protection against diabetes and tumors. These valuable bio-functional properties place it among the most exquisite candidates for probiotic use as a starter culture in the production of health-beneficial dairy foods, such as the kefir beverage.

scholarly journals Isolation, Identification, and Characterization of Pectinolytic Yeasts for Starter Culture in Coffee Fermentation

2019 ◽  
Vol 7 (10) ◽  
pp. 401 ◽  
Author(s):  
Mesfin Haile ◽  
Won Hee Kang
Keyword(s):  
Phylogenetic Trees ◽  
Starter Culture ◽  
Evolutionary Relationship ◽  
Pectin Methylesterase ◽  
Growth Media ◽  
Pichia Kudriavzevii ◽  
Coffee Pulp ◽  
Yeast Extract Peptone Dextrose ◽  
Wet Processing ◽  
Relationship Of

This experiment was carried out to identify and select pectinolytic yeasts that have potential use as a starter culture for coffee fermentation during wet processing. The coffee fruit was fermented for 48 h at 28 °C and a sample was taken from the fermented solution and spread onto yeast extract-peptone-dextrose agar (YPDA) media and incubated at 28 °C. A total of 28 yeasts were isolated, eight of which had the ability to produce pectinase enzymes. The species of those eight yeasts were molecularly identified and confirmed. These yeasts are Wickerhamomyces anomalus (strain KNU18Y3), Saccharomycopsis fibuligera (strain KNU18Y4), Papiliotrema flavescens (strain KNU18Y5 and KNU18Y6), Pichia kudriavzevii (strain KNU18Y7 and KNU18Y8), and Saccharomyces cerevisiae (strain KNU18Y12 and KNU18Y13). The pectin degradation index of S. fibuligera (strain KNU18Y4), W. anomalus (strain KNU18Y3), and P. flavescens (strain KNU18Y6) were higher compared to the others, at 178%, 160%, and 152%, respectively. The pectinase enzyme assays were made on two growth media: coffee pulp media (CPM) and synthetic pectin media (SPM). S. fibuligera (strain KNU18Y4) and W. anomalus (strain KNU18Y3) had great potential in producing polygalacturonase (PG) and pectin lyase (PL) compared to others in both media. However, S. cerevisiae strains (KNU18Y12 and KNU18Y13) produced higher pectin methylesterase (PME). Using MEGA 6 software, the phylogenetic trees were constructed to determine the evolutionary relationship of newly identified yeasts from our experiment and previously published yeast species. The sequences of the yeasts were deposited in the National Center for Biotechnology Information (NCBI) database.

Transmission Scanning Electron Microscopy and Energy Analysis with the Siemens ELMISKOP 101

1972 ◽  
Vol 30 ◽  
pp. 450-451
Author(s):  
H. M. Thieringer
Keyword(s):  
Objective Lens ◽  
Transmission Microscopy ◽  
Image Recording ◽  
Mode Of Operation ◽  
Scanning Transmission ◽  
Electron Microscopes ◽  
And Performance ◽  
Convergent Beam ◽  
Ray Path ◽  
Beam Diffraction

It has repeatedly been show that with conventional electron microscopes very fine electron probes can be produced, therefore allowing various micro-techniques such as micro recording, X-ray microanalysis and convergent beam diffraction. In this paper the function and performance of an SIEMENS ELMISKOP 101 used as a scanning transmission microscope (STEM) is described. This mode of operation has some advantages over the conventional transmission microscopy (CTEM) especially for the observation of thick specimen, in spite of somewhat longer image recording times.Fig.1 shows schematically the ray path and the additional electronics of an ELMISKOP 101 working as a STEM. With a point-cathode, and using condensor I and the objective lens as a demagnifying system, an electron probe with a half-width ob about 25 Å and a typical current of 5.10-11 amp at 100 kV can be obtained in the back focal plane of the objective lens.

Angular Resolved Electron Spectroscopy with Parallel Recording

1990 ◽  
Vol 48 (2) ◽  
pp. 370-371
Author(s):  
Huang Min ◽  
P.S. Flora ◽  
C.J. Harland ◽  
J.A. Venables
Keyword(s):  
Electron Spectroscopy ◽  
Low Voltage ◽  
Solid Angle ◽  
Detection System ◽  
Voltage Electron ◽  
Cylindrical Mirror ◽  
Inner Radius ◽  
Channel Plate ◽  
And Performance ◽  
Type Detector

A cylindrical mirror analyser (CMA) has been built with a parallel recording detection system. It is being used for angular resolved electron spectroscopy (ARES) within a SEM. The CMA has been optimised for imaging applications; the inner cylinder contains a magnetically focused and scanned, 30kV, SEM electron-optical column. The CMA has a large inner radius (50.8mm) and a large collection solid angle (Ω > 1sterad). An energy resolution (ΔE/E) of 1-2% has been achieved. The design and performance of the combination SEM/CMA instrument has been described previously and the CMA and detector system has been used for low voltage electron spectroscopy. Here we discuss the use of the CMA for ARES and present some preliminary results.The CMA has been designed for an axis-to-ring focus and uses an annular type detector. This detector consists of a channel-plate/YAG/mirror assembly which is optically coupled to either a photomultiplier for spectroscopy or a TV camera for parallel detection.

Novel epoxy/anhydride alternatives for biological electron microscopy: Physical and performance characteristis of embed 812 and LX 112 in combination with NSA/NMA/DMAE

1989 ◽  
Vol 47 ◽  
pp. 1000-1001
Author(s):  
Joe A. Mascorro ◽  
Gerald S. Kirby
Keyword(s):  
Electron Microscopy ◽  
Flow Rate ◽  
Succinic Anhydride ◽  
Volume Flow Rate ◽  
Mass Density ◽  
Uranyl Acetate ◽  
Volume Flow ◽  
Base Resin ◽  
And Performance ◽  
Acid Anhydrides

Embedding media based upon an epoxy resin of choice and the acid anhydrides dodecenyl succinic anhydride (DDSA), nadic methyl anhydride (NMA), and catalyzed by the tertiary amine 2,4,6-Tri(dimethylaminomethyl) phenol (DMP-30) are widely used in biological electron microscopy. These media possess a viscosity character that can impair tissue infiltration, particularly if original Epon 812 is utilized as the base resin. Other resins that are considerably less viscous than Epon 812 now are available as replacements. Likewise, nonenyl succinic anhydride (NSA) and dimethylaminoethanol (DMAE) are more fluid than their counterparts DDSA and DMP- 30 commonly used in earlier formulations. This work utilizes novel epoxy and anhydride combinations in order to produce embedding media with desirable flow rate and viscosity parameters that, in turn, would allow the medium to optimally infiltrate tissues. Specifically, embeding media based on EmBed 812 or LX 112 with NSA (in place of DDSA) and DMAE (replacing DMP-30), with NMA remaining constant, are formulated and offered as alternatives for routine biological work.Individual epoxy resins (Table I) or complete embedding media (Tables II-III) were tested for flow rate and viscosity. The novel media were further examined for their ability to infilftrate tissues, polymerize, sectioning and staining character, as well as strength and stability to the electron beam and column vacuum. For physical comparisons, a volume (9 ml) of either resin or media was aspirated into a capillary viscocimeter oriented vertically. The material was then allowed to flow out freely under the influence of gravity and the flow time necessary for the volume to exit was recored (Col B,C; Tables). In addition, the volume flow rate (ml flowing/second; Col D, Tables) was measured. Viscosity (n) could then be determined by using the Hagen-Poiseville relation for laminar flow, n = c.p/Q, where c = a geometric constant from an instrument calibration with water, p = mass density, and Q = volume flow rate. Mass weight and density of the materials were determined as well (Col F,G; Tables). Infiltration schedules utilized were short (1/2 hr 1:1, 3 hrs full resin), intermediate (1/2 hr 1:1, 6 hrs full resin) , or long (1/2 hr 1:1, 6 hrs full resin) in total time. Polymerization schedules ranging from 15 hrs (overnight) through 24, 36, or 48 hrs were tested. Sections demonstrating gold interference colors were collected on unsupported 200- 300 mesh grids and stained sequentially with uranyl acetate and lead citrate.

Trace nanoanalysis

1994 ◽  
Vol 52 ◽  
pp. 940-941
Author(s):  
D. E. Newbury ◽  
R. D. Leapman
Keyword(s):  
High Performance ◽  
Secondary Ion Mass Spectrometry ◽  
Detection Efficiency ◽  
Volume Element ◽  
And Performance ◽  
Trace Constituents ◽  
Secondary Ion ◽  
Concentration Levels ◽  
Structure Properties

Trace constituents, which can be very loosely defined as those present at concentration levels below 1 percent, often exert influence on structure, properties, and performance far greater than what might be estimated from their proportion alone. Defining the role of trace constituents in the microstructure, or indeed even determining their location, makes great demands on the available array of microanalytical tools. These demands become increasingly more challenging as the dimensions of the volume element to be probed become smaller. For example, a cubic volume element of silicon with an edge dimension of 1 micrometer contains approximately 5×1010 atoms. High performance secondary ion mass spectrometry (SIMS) can be used to measure trace constituents to levels of hundreds of parts per billion from such a volume element (e. g., detection of at least 100 atoms to give 10% reproducibility with an overall detection efficiency of 1%, considering ionization, transmission, and counting).

Relationship of stress and performance among first-year dental students

1986 ◽  
Vol 50 (5) ◽  
pp. 264-267 ◽  
Author(s):  
GH Westerman ◽  
TG Grandy ◽  
JV Lupo ◽  
RE Mitchell
Keyword(s):  
Dental Students ◽  
First Year ◽  
And Performance ◽  
Relationship Of

Linguistic Competence in Aphasia

2008 ◽  
Vol 17 (3) ◽  
pp. 87-92
Author(s):  
Leonard L. LaPointe
Keyword(s):  
Language Use ◽  
Linguistic Competence ◽  
Careful Study ◽  
Feral Children ◽  
Performance Factors ◽  
Performance Loss ◽  
Linguistic Rules ◽  
Communication Goals ◽  
Aphasia Treatment ◽  
And Performance

Abstract Loss of implicit linguistic competence assumes a loss of linguistic rules, necessary linguistic computations, or representations. In aphasia, the inherent neurological damage is frequently assumed by some to be a loss of implicit linguistic competence that has damaged or wiped out neural centers or pathways that are necessary for maintenance of the language rules and representations needed to communicate. Not everyone agrees with this view of language use in aphasia. The measurement of implicit language competence, although apparently necessary and satisfying for theoretic linguistics, is complexly interwoven with performance factors. Transience, stimulability, and variability in aphasia language use provide evidence for an access deficit model that supports performance loss. Advances in understanding linguistic competence and performance may be informed by careful study of bilingual language acquisition and loss, the language of savants, the language of feral children, and advances in neuroimaging. Social models of aphasia treatment, coupled with an access deficit view of aphasia, can salve our restless minds and allow pursuit of maximum interactive communication goals even without a comfortable explanation of implicit linguistic competence in aphasia.

Sign in / Sign up

Export Citation Format

Share Document