Thin Film Condensation Supported on Ambiphilic Microstructures

2017 ◽  
Vol 139 (2) ◽  
Author(s):  
Emre Ölçeroğlu ◽  
Chia-Yun Hsieh ◽  
Kenneth K. S. Lau ◽  
Matthew McCarthy
Keyword(s):  
Thin Film ◽  
Thermal Resistance ◽  
Liquid Film ◽  
Thin Liquid Film ◽  
Environmental Scanning Electron Microscopy ◽  
Hierarchical Structures ◽  
Liquid Films ◽  
Film Condensation ◽  
Environmental Scanning ◽  
C 50

Ambiphilic surfaces have been used to support thin liquid films during condensation and imaged using environmental scanning electron microscopy (ESEM). Ambiphilic microstructures (a) are comprised of hydrophilic deep etched silicon micropillars with hydrophobic post tops made of PTFE deposited using iCVD. By restraining the growth of the liquid film using hydrophobic post tops (b), thermal resistance is reduced and heat transfer is increased. During condensation on ambiphilic microstructures the condensate initially fills the post array (b), but then bursts outward to accommodate continued production of liquid (c). This creates a low contact angle droplet on the surface (c), and could lead to complete flooding and decreased performance. With the addition of hydrophilic nanostructures to the micropost array (d), ambiphilic hierarchical structures have been fabricated with dedicated burst sites (e). During condensation the structures maintain a thin liquid film and excess liquid emerges from the burst sites as highly mobile spherical droplets (e). This maximizes the thin film area available for vapor-to-liquid phase change while minimizing thermal resistance across the condensate layer. Scale bars: (a) 5 µm, (b,c) 50 µm, (d) 2 µm, and (e) 25 µm.

Effect of Thin Film Condensation on Thermal Performance of Oscillating Heat Pipes

2006 ◽  
Author(s):  
S. B. Liang ◽  
G. P. Xu
Keyword(s):  
Thin Film ◽  
Liquid Film ◽  
Heat Pipe ◽  
Heat Transport ◽  
Slug Flow ◽  
Thin Liquid Film ◽  
Experimental Studies ◽  
Heat Pipes ◽  
Film Condensation ◽  
Working Fluid

Self-sustainable motions of the slug flow in oscillating heat pipes have been investigated in the paper. Thin film condensation in the capillary channels of the condenser of the oscillating heat pipes was studied. Instability of the thin liquid film on the characteristics of heat pipes was analysed. The extra thermal resistance caused by the thickness of the thin liquid film was taken into account for the numerical simulation of the oscillatory motions of the slug flow in the heat pipes. Saturated temperatures and pressures of the working fluid in the condenser were obtained. Thermoacoustic theory was applied to calculate heat transport through the adiabatic section of the heat pipes. Experimental studies were carried out to understand the heat transfer behaviours of heat pipes. One heat pipe with the working fluid of HFC-134a was evaluated. The heat pipe is made of aluminium plate and has the width of 50 mm and thickness of 1.9 mm. Numerical and experimental results relevant to the heat transport capability of the heat pipe were analysed and compared.

The motion of rotating cylinders sliding on pebbled ice

2000 ◽  
Vol 77 (11) ◽  
pp. 847-862 ◽  
Author(s):  
MRA Shegelski ◽  
M Reid ◽  
R Niebergall
Keyword(s):  
Thin Film ◽  
Liquid Film ◽  
Contact Area ◽  
Relative Velocity ◽  
Thin Liquid Film ◽  
Center Of Mass ◽  
Translational Motion ◽  
Rotating Cylinder ◽  
Outer Edge ◽  
Slow Rotation

We consider the motion of a cylinder with the same mass and sizeas a curling rock, but with a very different contact geometry.Whereas the contact area of a curling rock is a thin annulus havinga radius of 6.25 cm and width of about 4 mm, the contact area of the cylinderinvestigated takes the form of several linear segments regularly spacedaround the outer edge of the cylinder, directed radially outward from the center,with length 2 cm and width 4 mm. We consider the motion of this cylinderas it rotates and slides over ice having the nature of the ice surfaceused in the sport of curling. We have previously presented a physicalmodel that accounts for the motion of curling rocks; we extend this modelto explain the motion of the cylinder under investigation. In particular,we focus on slow rotation, i.e., the rotational speed of the contact areasof the cylinder about the center of mass is small compared to thetranslational speed of the center of mass.The principal features of the model are (i) that the kineticfriction induces melting of the ice, with the consequence that thereexists a thin film of liquid water lying between the contact areasof the cylinder and the ice; (ii) that the radial segmentsdrag some of the thin liquid film around the cylinder as it rotates,with the consequence that the relative velocity between the cylinderand the thin liquid film is significantly different than the relativevelocity between the cylinder and the underlying solid ice surface.Since it is the former relative velocity that dictates the nature of themotion of the cylinder, our model predicts, and observations confirm, thatsuch a slowly rotating cylinder stops rotating well before translationalmotion ceases. This is in sharp contrast to the usual case of most slowlyrotating cylinders, where both rotational and translational motion ceaseat the same instant. We have verified this prediction of our model bycareful comparison to the actual motion of a cylinder having a contactarea as described.PACS Nos.: 46.00, 01.80+b

scholarly journals Visualization of Surface Acoustic Waves in Thin Liquid Films

2016 ◽  
Vol 6 (1) ◽  
Author(s):  
R. W. Rambach ◽  
J. Taiber ◽  
C. M. L. Scheck ◽  
C. Meyer ◽  
J. Reboud ◽  
...  
Keyword(s):  
Liquid Film ◽  
Acoustic Waves ◽  
Low Cost ◽  
Thin Liquid Film ◽  
Surface Acoustic Waves ◽  
Liquid Films ◽  
Theoretical Description ◽  
Propagation Path ◽  
Microfluidic Channels ◽  
Potential Applications

Abstract We demonstrate that the propagation path of a surface acoustic wave (SAW), excited with an interdigitated transducer (IDT), can be visualized using a thin liquid film dispensed onto a lithium niobate (LiNbO3) substrate. The practical advantages of this visualization method are its rapid and simple implementation, with many potential applications including in characterising acoustic pumping within microfluidic channels. It also enables low-cost characterisation of IDT designs thereby allowing the determination of anisotropy and orientation of the piezoelectric substrate without the requirement for sophisticated and expensive equipment. Here, we show that the optical visibility of the sound path critically depends on the physical properties of the liquid film and identify heptane and methanol as most contrast rich solvents for visualization of SAW. We also provide a detailed theoretical description of this effect.

The Meniscus Instability of a Thin Liquid Film

1988 ◽  
Vol 55 (4) ◽  
pp. 975-980 ◽  
Author(s):  
H. Koguchi ◽  
M. Okada ◽  
K. Tamura
Keyword(s):  
Thin Film ◽  
Analytical Solution ◽  
Liquid Film ◽  
Tilt Angle ◽  
Stability Criterion ◽  
Thin Liquid Film ◽  
Normal Direction ◽  
Wave Number ◽  
The Stability ◽  
Maximum Amplification

This paper reports on the instability for the meniscus of a thin film of a very viscous liquid between two tilted plates, which are separated at a constant speed with a tilt angle in the normal direction of the plates. The disturbances on the meniscus moving with movement of the plates are examined experimentally and theoretically. The disturbances are started when the velocity of movement of the plates exceeds a critical one. The wavelength of the disturbances is measured by using a VTR. The instability of the meniscus is studied theoretically using the linearized perturbation method. A simple and complete analytical solution yields both a stability criterion and the wave number for a linear thickness geometry. These results compared with experiments for the instability show the validity of the stability criterion and the best agreement is obtained with the wave number of maximum amplification.

Evaporation of Gravity- and Gas Flow-Driven Thin Liquid Films in Micro- and Minigrooves

2004 ◽  
Author(s):  
T. Gambaryan-Roisman ◽  
P. Stephan
Keyword(s):  
Thin Film ◽  
Heat Transfer ◽  
Gas Flow ◽  
Thin Liquid Film ◽  
Flow Region ◽  
Wave Theory ◽  
Liquid Films ◽  
Wall Material ◽  
Wall Structure ◽  
Ultra Thin Film

Using microstructured wall surfaces may improve the heat transfer performance of falling film or shear-driven film cooling devices enormously. The advantages of the structured surface include the prevention of the formation of dry patches on hot surfaces, the promotion of ultra-thin film evaporation, and a wavy motion of the film that enhances mixing of the liquid. We develop a model describing the hydrodynamics and heat transfer by evaporation of gravity- and gas flow-driven liquid films on grooved surfaces. For low Reynolds numbers or low liquid mass fluxes the heat transfer is governed by the evaporation of the ultra-thin film at a micro region, in the vicinity of the three-phase contact line. We investigate the hydrodynamic stability of the film flow using the long-wave theory. In addition to the films completely covering the wall structure, we study the stability characteristics of a thin liquid film partly covering the grooved wall, so that the flow region is bounded by contact lines. Two cases are analyzed: fully wetting liquids and liquids which form a small but finite contact angle with the wall material.

scholarly journals On the origin of the circular hydraulic jump in a thin liquid film

2018 ◽  
Vol 851 ◽  
Author(s):  
Rajesh K. Bhagat ◽  
N. K. Jha ◽  
P. F. Linden ◽  
D. Ian Wilson
Keyword(s):  
Thin Film ◽  
Surface Tension ◽  
Liquid Film ◽  
Thin Liquid Film ◽  
Capillary Waves ◽  
Hydraulic Jumps ◽  
Planar Surface ◽  
Normal Impact ◽  
Viscous Forces

This study explores the formation of circular thin-film hydraulic jumps caused by the normal impact of a jet on an infinite planar surface. For more than a century, it has been believed that all hydraulic jumps are created due to gravity. However, we show that these thin-film hydraulic jumps result from energy loss due to surface tension and viscous forces alone. We show that, at the jump, surface tension and viscous forces balance the momentum in the liquid film and gravity plays no significant role. Experiments show no dependence on the orientation of the surface and a scaling relation balancing viscous forces and surface tension collapses the experimental data. A theoretical analysis shows that the downstream transport of surface energy is the previously neglected critical ingredient in these flows, and that capillary waves play the role of gravity waves in a traditional jump in demarcating the transition from the supercritical to subcritical flow associated with these jumps.

Simultaneous measurement of dynamic force and spatial thin film thickness between deformable and solid surfaces by integrated thin liquid film force apparatus

Soft Matter ◽  
2016 ◽  
Vol 12 (44) ◽  
pp. 9105-9114 ◽  
Author(s):  
Xurui Zhang ◽  
Plamen Tchoukov ◽  
Rogerio Manica ◽  
Louxiang Wang ◽  
Qingxia Liu ◽  
...  
Keyword(s):  
Thin Film ◽  
Film Thickness ◽  
Liquid Film ◽  
Simultaneous Measurement ◽  
Thin Liquid Film ◽  
Solid Surfaces ◽  
Dynamic Force ◽  
Thin Film Thickness

Evaluation of Pulsed Laser Deposited Li4Ti5O12 Thin Film Anodes by CV and EIS

2013 ◽  
Vol 743-744 ◽  
pp. 13-19 ◽  
Author(s):  
Jian Qiu Deng ◽  
Zhou Guang Lu ◽  
Chi Yuen Chung ◽  
Zhong Min Wang ◽  
Huai Ying Zhou
Keyword(s):  
Thin Film ◽  
Electrochemical Impedance ◽  
Discharge Rate ◽  
Pulsed Laser ◽  
Environmental Scanning Electron Microscopy ◽  
Cycling Performance ◽  
Laser Deposition ◽  
Environmental Scanning ◽  
X Ray Diffraction ◽  
X Ray

Li4Ti5O12thin film anodes were prepared successfully using pulsed laser deposition technique. The thin films were characterized by X-ray diffraction and environmental scanning electron microscopy. The effects of thickness and scan rate on the electrochemical properties of Li4Ti5O12thin film electrodes were discussed in detail. The thin film anodes deliver favorable capacity and excellent cycling performance. The discharge capacity maintains at 141 mAhg-1after 20 cycles at 1C charge-discharge rate for the thin film anodes deposited for 20 minutes. The charge-transfer resistances were also investigated by electrochemical impedance spectroscopy.

scholarly journals Modeling of Partially Wetting Liquid Film Using an Enhanced Thin Film Model for Aero-Engine Bearing Chamber Applications

2021 ◽  
Vol 143 (4) ◽  
Author(s):  
Kuldeep Singh ◽  
Medhat Sharabi ◽  
Richard Jefferson-Loveday ◽  
Stephen Ambrose ◽  
Carol Eastwick ◽  
...  
Keyword(s):  
Thin Film ◽  
Contact Angle ◽  
Film Thickness ◽  
Liquid Film ◽  
Thin Liquid Film ◽  
Operating Conditions ◽  
Film Model ◽  
Thin Film Model ◽  
Wide Range ◽  
Aero Engine

Abstract In the case of aero-engine, thin lubricating film servers dual purpose of lubrication and cooling. Prediction of dry patches or lubricant starved region in bearing or bearing chambers are required for safe operation of these components. In this work, thin liquid film flow is numerically investigated using the framework of the Eulerian thin film model (ETFM) for conditions, which exhibit partial wetting phenomenon. This model includes a parameter that requires adjustment to account for the dynamic contact angle. Two different experimental data sets have been used for comparisons against simulations, which cover a wide range of operating conditions including varying the flowrate, inclination angle, contact angle, and liquid–gas surface tension coefficient. A new expression for the model parameter has been proposed and calibrated based on the simulated cases. This is employed to predict film thickness on a bearing chamber which is subjected to a complex multiphase flow. From this study, it is observed that the proposed approach shows good quantitative comparisons of the film thickness of flow down an inclined plate and for the representative bearing chamber. A comparison of model predictions with and without wetting and drying capabilities is also presented on the bearing chamber for shaft speed in the range of 2500 RPM to 10,000 RPM and flowrate in the range of 0.5 liter per minute (LPM) to 2.5 LPM.

The Influence of Evaporation in Shear-Driven Liquid Film on Heat Removal From Local Heater

2006 ◽  
Author(s):  
Elizaveta Gatapova ◽  
Oleg Kabov
Keyword(s):  
Liquid Film ◽  
Thin Liquid Film ◽  
Heat Removal ◽  
Film Surface ◽  
Numerical Data ◽  
High Heat ◽  
Liquid Films ◽  
High Heat Flux ◽  
Maximal Surface ◽  
High Heat Transfer

The present work focuses upon shear-driven liquid film evaporative cooling of high heat flux local heater. Thin evaporating liquid films may provide very high heat transfer rates and can be used for cooling of high power microelectronic systems. Thermocapillary convection in a liquid film falling down a locally heated substrate has recently been extensively studied. However, non-uniform heating effects remain only partially understood for shear-driven liquid films. The combined effects of evaporation, thermocapillarity and gas dynamics as well as formation of microscopic adsorbed film have not been studied. The effect of evaporation on heat and mass transfer for 2D joint flow of a liquid film and gas is theoretically and numerically investigated. The convective terms in the energy equations are taken into account. The calculations reveal that evaporation from film surface essential influences on heat removal from local heater. It is shown that the thermal boundary layer plays significant role for cooling local heater by evaporating thin liquid film. Measured by an infrared scanner temperature distribution at the film surface is compared with numerical data. Calculations satisfactorily describe the maximal surface temperature value.

Sign in / Sign up

Export Citation Format

Share Document