A Comprehensive Experimental Investigation of the Performance of Closed-Loop Pulsating Heat Pipes

2017 ◽  
Vol 139 (9) ◽  
Author(s):  
M. Halimi ◽  
A. Abbas Nejad ◽  
M. Norouzi
Keyword(s):  
Thermal Resistance ◽  
Flow Regime ◽  
Thermal Performance ◽  
Closed Loop ◽  
Heat Pipes ◽  
Filling Ratio ◽  
Working Fluid ◽  
Physical Parameters ◽  
Two Phase ◽  
Laboratory Conditions

Closed-loop pulsating heat pipes (CLPHPs) are a new type of two-phase heat transfer devices that can transfer considerable heat in a small space via two-phase vapor and liquid pulsating flow and work with various types of two-phase instabilities so the operating mechanism of CLPHP is not well understood. In this work, two CLPHPs, made of Pyrex, were manufactured to observe and investigate the flow regime that occurs during the operation of CLPHP and thermal performance of the device under different laboratory conditions. In general, various working fluids were used in filling ratios of 40%, 50%, and 60% in horizontal and vertical modes to investigate the effect of thermo-physical parameters, filling ratio, nanoparticles, gravity, CLPHP structure, and input heat flux on the thermal performance of CLPHP. The results indicate that three types of flow regime may be observed given laboratory conditions. Each flow regime exerts a different effect on the thermal performance of the device. There is an optimal filling ratio for each working fluid. The increased number of turns in CLPHP generally improves the thermal performance of the system reducing the effect of the type of the working fluid on the aforementioned performance. The adoption of copper nanoparticles, which positively affect fluid motion, decreases the thermal resistance of the system as much as 6.06–42.76% depending on laboratory conditions. Moreover, gravity brings about positive changes in the flow regime decreasing thermal resistance as much as 32.13–52.58%.

Experimental Investigation on Thermal Performance of Flat Plate Heat Pipe with Intersected Micro-Grooves

2013 ◽  
Vol 772 ◽  
pp. 480-486 ◽  
Author(s):  
Chen Wang ◽  
Zhong Liang Liu ◽  
Guang Meng Zhang
Keyword(s):  
Thermal Resistance ◽  
Flat Plate ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Radial Direction ◽  
Filling Ratio ◽  
Working Fluid ◽  
Plate Heat ◽  
Inclination Angles ◽  
Flat Plate Heat Pipe

A copper-water flat plate heat pipe with intersected micro-grooves was developed for cooling electronic devices in this paper. The effects of heat flux, working fluid filling ratio and inclination angles on thermal performance of the flat plate heat pipe was tested and investigated. The laboratory tests show the optimal filling ratio of the heat pipe is about 65%. Excellent thermal performance is also observed in unfavorable titled positions including vertical and anti-gravity orientation at 65%. The smallest overall thermal resistance is obtained in horizontal position and the maximal thermal resistance is observed in vertical position. The influence of inclination angles on thermal performance of the heat pipe in both axial direction and radial direction is also investigated. As the heat pipe is tilted, the ability of temperature leveling in radial direction is enhanced, nevertheless, the capacity of heat transfer in radial direction decreased at the same time.

Thermal Characteristics of a Circular Finned Thermosyphon Using Different Working Fluids

2014 ◽  
Vol 575 ◽  
pp. 322-328 ◽  
Author(s):  
Narayanan Alagappan ◽  
Narayanan Karunakaran
Keyword(s):  
Experimental Study ◽  
Ethylene Glycol ◽  
Thermal Resistance ◽  
Thermal Performance ◽  
Heat Input ◽  
Base Fluid ◽  
Thermal Characteristics ◽  
Working Fluid ◽  
Two Phase ◽  
Evaporation And Condensation

The two-phase closed thermosyphon (TPCT), which is essentially a gravity-assisted wickless heat pipe, utilizes the evaporation and condensation of the working fluid inside the TPCT to transport heat. This experimental study was carried out to understand the thermal performance of circular finned thermosyphon using nanofluid with alcohol and was analyzed, compared with alcohol and base fluid DI water. The concentration of nanoparticle used in this setup was 110mg/lit of TiO2combined with 0.2 ml of ethylene glycol. The heat input (Q) were 10W, 12W, 14 W and 16 W and the orientation 30°, 45°, 60° and 90°.The results demonstrate that TiO2nanofluid with 0.2 ml of ethylene glycol improves the performance through reduction in thermal resistance by 85.86%.

THERMAL PERFORMANCE OF FLAT PLATE PULSATING HEAT PIPES WITH MINI- AND MICROCHANNELS

2014 ◽  
Vol 22 (04) ◽  
pp. 1450025 ◽  
Author(s):  
DONG SOO JANG ◽  
EUN-JI LEE ◽  
SANG HUN LEE ◽  
YONGCHAN KIM
Keyword(s):  
Cross Section ◽  
Working Conditions ◽  
Thermal Performance ◽  
Strong Influence ◽  
Heat Pipes ◽  
Input Power ◽  
Filling Ratio ◽  
Hydraulic Diameter ◽  
Working Fluid ◽  
Optimum Working

This study presents the thermal performance of pulsating heat pipes (PHPs) using distilled water with mini- and microchannels. The PHPs were fabricated with the channels of square cross section which had hydraulic diameters ranged from 1.6 to 3.2 mm in minichannels and from 0.714 to 0.941 mm in microchannels. The performance of the PHPs was measured and analyzed by varying hydraulic diameter, number of turns, filling ratio, and input power. The filling ratio of the working fluid varied from 0% to 100%. The input power was controlled in the range between 3.6 and 150 W. The hydraulic diameter, number of turns, filling ratio, and input power showed strong influence on the performance of the PHP. In the PHP models with mini- and microchannels, optimum working conditions, such as filling ratio and heat input, were quite different according to channel size.

Promising Technology for Electronic Cooling: Nanofluidic Micro Pulsating Heat Pipes

2013 ◽  
Vol 135 (2) ◽  
Author(s):  
Kambiz Jahani ◽  
Maziar Mohammadi ◽  
Mohammad Behshad Shafii ◽  
Zahra Shiee
Keyword(s):  
Magnetic Field ◽  
Thermal Resistance ◽  
Thermal Management ◽  
Thermal Performance ◽  
Microelectromechanical Systems ◽  
Heat Pipes ◽  
Electronic Cooling ◽  
Working Fluid ◽  
Pulsating Heat Pipe ◽  
Thermal Management Of Electronics

Currently, the thermal management of microelectromechanical systems (MEMS) has become a challenge. In the present research, a micro pulsating heat pipe (MPHP) with a hydraulic diameter of 508 μm, is experimented. The thermal performance of the MPHP in both the transient and steady conditions, the effects of the working fluid (water, silver nanofluid, and ferrofluid), heating power (4, 8, 12, 16, 20, 24, and 28 W), charging ratio (20, 40, 60, and 80%), inclination angle (0 deg, 25 deg, 45 deg, 75 deg, and 90 deg relative to horizontal axis), and the application of magnetic field, are investigated and thoroughly discussed. The experimental results show that the optimum charging ratio for water is 40%, while this optimum for nanofluids is 60%. In most of situations, the nanofluid charged MPHPs have a lower thermal resistance relative to the water charged ones. For ferrofluid charged MPHP, the application of a magnetic field substantially reduces the thermal resistance. This study proposes an outstanding technique for the thermal management of electronics.

scholarly journals Potential of Solar Collectors for Clean Thermal Energy Production in Smart Cities using Nanofluids: Experimental Assessment and Efficiency Improvement

2019 ◽  
Vol 9 (9) ◽  
pp. 1877 ◽  
Author(s):  
M. Sarafraz ◽  
Iskander Tlili ◽  
Mohammad Abdul Baseer ◽  
Mohammad Safaei
Keyword(s):  
Flow Rate ◽  
Thermal Performance ◽  
Tilt Angle ◽  
Thermal Efficiency ◽  
Smart Cities ◽  
Heat Pipes ◽  
Filling Ratio ◽  
Working Fluid ◽  
Solar Thermal Collector ◽  
Evacuated Tube

In this article, an experimental study was performed to assess the potential thermal application of a new nanofluid comprising carbon nanoparticles dispersed in acetone inside an evacuated tube solar thermal collector. The effect of various parameters including the circulating volumetric flow of the collector, mass fraction of the nanoparticles, the solar irradiance, the tilt angle and the filling ratio values of the heat pipes on the thermal performance of the solar collector was investigated. It was found that with an increase in the flow rate of the working fluid within the system, the thermal efficiency of the system was improved. Additionally, the highest thermal performance and the highest temperature difference between the inlet and the outlet ports of the collector were achieved for the nanofluid at wt. % = 0.1. The best tilt angle and the filling ratio values of the collector were 30° and 60% and the maximum thermal efficiency of the collector was 91% for a nanofluid at wt. % = 0.1 and flow rate of 3 L/min.

scholarly journals Experimental study on heat transfer characteristics of a modified two-phase closed thermosyphon

2017 ◽  
Vol 21 (6 Part A) ◽  
pp. 2481-2489 ◽  
Author(s):  
Babak Aghel ◽  
Masoud Rahimi ◽  
Saeed Almasi
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Experimental Study ◽  
Thermal Resistance ◽  
Thermal Performance ◽  
Working Fluid ◽  
Heat Transfer Characteristics ◽  
Two Phase ◽  
Transfer Characteristics ◽  
Adiabatic Section

This study investigated the heat transfer characteristics of modified two-phase closed thermosyphon (TPCT) using water as the working fluid. In the modified TPCT, to reduce thermal resistance, a small TPCT was inserted inside the adiabatic section. For both the plain and modified thermosyphons the performances were determined at various heat inputs from 71-960 W. The results showed that the modified TPCT had less temperature difference between the evaporator and condenser sections than the plain one. According to the experimental data, in the modified TPCT, the thermal performance increased up to 20% over that of the unmodified one.

scholarly journals Effect of Working Fluid on Thermal Performance of Closed Loop Pulsating Heat Pipe

2019 ◽  
Vol 9 (2) ◽  
pp. 953-956
Keyword(s):  
Thermal Resistance ◽  
Heat Pipe ◽  
Closed Loop ◽  
Filling Ratio ◽  
Working Fluid ◽  
External Diameter ◽  
Pulsating Heat Pipe ◽  
Condenser Section ◽  
Heat Transfer Efficiency ◽  
Bottom Heat

The pulsing heat pipe (PHP) is an technology that is increasingly capable of applying many manufacturing areas, but a thorough knowledge of its thermo-hydrodynamic There's far from enough system. This research explored the features of oscillation and the heat transfer efficiency of a closed-loop PHP using an internal and external diameter copper tube with 2.0 and 3.0 mm respectively. For all experimentation, filling ratio (FR) was 40%, five turns and different heat inputs of 20 to 80 W was supplied to PHP. The position of the PHP was vertical bottom heat type. 52 mm, 170 mm,60 mm was retained for the duration of the evaporator, adiabatic and condenser section. Water, Ethanol are chosen as working liquids. To understand, thermal resistance features and median evaporator pressures for multiple operating liquids at distinct heat inputs. An significant consideration for the results of PHPs is the research on PHP stated operating fluid. The result demonstrates that, with the rise of the heating output from 20 to 80 W, where as steadily increases above 80W, the thermal resistance reduces faster. By comparing Water , Ethanol working fluids, Ethanol provides the highest heat performance . The simulation is performed in Mat lab and the results have been contrasted

An Experimental Study of Closed Loop Two-Phase Thermosyphon for Spent Fuel Pool Passive Cooling

2016 ◽  
Author(s):  
Minglu Wang ◽  
Mingguang Zheng ◽  
Cheng Ye ◽  
Zhongming Qiu ◽  
Zhenqin Xiong
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Heat Transfer Coefficient ◽  
Thermal Resistance ◽  
Transfer Coefficient ◽  
Closed Loop ◽  
Working Fluid ◽  
Spent Fuel ◽  
Two Phase ◽  
Spent Fuel Pool

The study reported here examined a closed loop two-phase thermosyphon (CLTPT) of evaporator length 7.6m and internal diameter 65mm used to cool the spent fuel pool. This experimental study investigates the thermal performances and heat and mass transfer characteristic of CLTPT by examining the thermodynamic cycles and overall thermal resistances with ammonia, R134a and water as the working fluid. Measurements of temperature and pressure distributions of the fluid around the loop were made under various conditions. Results show that this loop operates with low filling ratio, low mass flow rate, and high heat-transfer coefficient and the CLTPT has the ability to cool the spent fuel pool. The working fluid flowing through the heat pipe evaporator section generally experienced a subcooled zone, pool boiling zone and high gas quality two-phase region. The average heat transfer coefficient of evaporator reaches 450 W/m2•°C using R134a as working fluid. The thermal resistance of R134a is always smaller than ammonia but the thermal resistance of water is largest at small temperature difference while is smallest when temperature difference is large.

scholarly journals Kinerja Termal Pipa Kalor Tembaga pada Fluida Kerja Air

Jurnal METTEK ◽  
2019 ◽  
Vol 5 (1) ◽  
pp. 52
Author(s):  
David Febraldo ◽  
Wayan Nata Septiadi ◽  
Ketut Astawa
Keyword(s):  
Heat Transfer ◽  
Heat Resistance ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Temperature Difference ◽  
Heating Temperature ◽  
Heat Pipes ◽  
Working Fluid ◽  
Fluid Temperature ◽  
Two Phase

Pipa kalor (Heat pipe) merupakan salah satu teknologi penukar kalor dua fase sistem pasif, pipa kalor itu sendiri memiliki struktur dengan konduktivitas termal tinggi, hal ini memungkinkan transportasi panas dengan mempertahankan perbedaan suhu sehingga seragam di sepanjang bagian yang dipanaskan dan didinginkan. Kinerja termal pipa kalor dapat ditentukan dari nilai hambatan panas. Ketika hambatan panas bernilai kecil, maka laju perpindahan kalor meningkat begitu pula sebaliknya. Pengujian kinerja termal  pipa kalor tembaga pada fluida kerja air telah dilakukan. Kinerja termal dapat diamati dari hasil pengambilan data temperatur dan pengolahan data. Hasil dari penelitian ini menunjukkan perbedaan temperatur antara temperatur pemanas dan dan temperatur fluida terus meningkat dengan kenaikan laju perpindahan panas dari variasi beban pemanasan 70 volt, 90 volt, 110 vot, 130 volt, dan 150 volt. Heat pipe is a passive two-phase heat exchanger technology, heat pipe itself has a structure with high thermal conductivity, this allows heat transportation by maintaining a uniform temperature difference along the heated and cooled part. Thermal performance of heat pipes can be determined from the value of heat resistance. When heat resistance is small, the heat transfer rate increases and vice versa. Testing the thermal performance of copper heat pipes on the working fluid of water has been carried out. Thermal performance can be observed from the results of temperature data collection and data processing. The results of this study indicate the temperature difference between heating temperature and fluid temperature continues to increase with increasing heat transfer rates from variations in heating loads of 70 volts, 90 volts, 110 vot, 130 volts, and 150 volts.

Sign in / Sign up

Export Citation Format

Share Document