Using Computer Simulation to Validate and Optimize the Design of an Innovative Electronic Packaging Concept

2000 ◽  
Author(s):  
Dagmar Beyerlein ◽  
Lee Hornberger
Keyword(s):  
Computer Simulation ◽  
Integrated Circuit ◽  
Empirical Studies ◽  
Simulation Software ◽  
Production Costs ◽  
Raw Material ◽  
Annual Production ◽  
Plastic Packaging ◽  
Software Application ◽  
Microchip Encapsulation

Abstract Reducing integrated circuit (IC) plastic packaging production costs by improving the transfer mold and leadframe designs is a costly and time-consuming process. Rather than building mold and leadframe prototypes to perform empirical studies, this research describes how C-MOLD, a microchip encapsulation simulation software application, was used to validate and optimize an innovative mold and leadframe design that has the potential to reduce raw material waste associated with packaging by more than 59%. Estimates indicate that the proposed design will cut annual production costs by more than $600,000.

Using Computer Simulation to Validate and Optimize the Design of an Innovative Electronic Packaging Concept

2001 ◽  
Vol 123 (4) ◽  
pp. 366-371
Author(s):  
Dagmar Beyerlein ◽  
Lee E. Hornberger
Keyword(s):  
Computer Simulation ◽  
Integrated Circuit ◽  
Empirical Studies ◽  
Simulation Software ◽  
Production Costs ◽  
Raw Material ◽  
Annual Production ◽  
Plastic Packaging ◽  
Software Application ◽  
Microchip Encapsulation

Reducing integrated circuit (IC) plastic packaging production costs by improving the transfer mold and leadframe designs is a costly and time-consuming process. Rather than building mold and leadframe prototypes to perform empirical studies, this research describes how C-MOLD, a microchip encapsulation simulation software application, was used to validate and optimize an innovative mold and leadframe design that has the potential to reduce raw material waste associated with packaging by more than 59 percent. Estimates indicate that the proposed design will cut annual production costs by more than $600,000.

Numerical Simulation of Filling and Solidification in Sand Casting by Procast

2013 ◽  
Vol 791-793 ◽  
pp. 550-553 ◽  
Author(s):  
Dong Dong Han ◽  
Cheng Jun Wang ◽  
Juan Chang ◽  
Lei Chen ◽  
Huai Bei Xie
Keyword(s):  
Numerical Simulation ◽  
Heat Dissipation ◽  
Solidification Process ◽  
Simulation Software ◽  
Sand Casting ◽  
Production Costs ◽  
Raw Material ◽  
Casting Defects ◽  
Three Dimension ◽  
Filling And Solidification

At present, pulley produced in China has been able to meet the demand of domestic and international markets. But there are many problem of the pulley industry in our country, such as too many production enterprises and the low level of export products. And as components of drive system are light weight and raw material price of pulley casting are rising, manufacturing requirements of the pulley are also more and more high. Aiming at the casting defects of pulley that enterprise current product, pulley casting blank model of common material HT250 be made by three-dimension software, numerical simulation of filling and solidification process for pulley sand casting by the casting simulation software Procast, the size and location of the various casting defects were forecasted and analyzed, reflecting the pulley filling and solidification process of the actual situation, due to the thicker pulley rim and less heat dissipation, position of shrinkage is close to the middle of rim [, a method of eliminating defects is proposed to realize sequential solidification, and thus to minimize porosity shrinkage and improve casting performance and reduce casting time and reduce production costs.

Simulation Software Application in "Power System Analysis" Course Teaching

2013 ◽  
Vol 791-793 ◽  
pp. 1748-1751
Author(s):  
Li Hua Sun ◽  
Xiao Zhi Gao
Keyword(s):  
Computer Simulation ◽  
Power System ◽  
Electric Power ◽  
System Analysis ◽  
Teaching Method ◽  
Electrical Engineering ◽  
Simulation Software ◽  
Electric Power System ◽  
Software Application ◽  
Power System Analysis

With the development of computer simulation software, its application has become an important teaching method in Electrical Engineering and some related courses. This paper introduced some frequently-used simulation software in electric power system, such as PWS, PSASP, and MATLAB etc., and especially analyzed the application of these software in "power system analysis" course teaching.

Graubündens Wald im Fokus | Focus on the Grisons forest

2009 ◽  
Vol 160 (7) ◽  
pp. 195-200
Author(s):  
Reto Hefti
Keyword(s):  
Climate Change ◽  
Global Warming ◽  
Natural Hazards ◽  
Positive Attitude ◽  
Production Costs ◽  
Raw Material ◽  
Intensive Use ◽  
Form Part ◽  
New Challenges ◽  
The Government

In the mountainous canton Grisons, much visited by tourists, the forest has always had an important role to play. New challenges are now presenting themselves. The article goes more closely into two themes on the Grisons forestry agenda dominating in the next few years: the increased use of timber and climate change. With the increased demand for logs and the new sawmill in Domat/Ems new opportunities are offered to the canton for more intensive use of the raw material, wood. This depends on a reduction in production costs and a positive attitude of the population towards the greater use of wood. A series of measures from the Grisons Forestry Department should be of help here. The risk of damage to infrastructure is particularly high in a mountainous canton. The cantonal government of the Grisons has commissioned the Forestry Department to define the situation concerning the possible consequences of global warming on natural hazards and to propose measures which may be taken. The setting up of extensive measurement and information systems, the elaboration of intervention maps, the estimation of the danger potential in exposed areas outside the building zone and the maintenance of existing protective constructions through the creation of a protective constructions register, all form part of the government programme for 2009 to 2012. In the Grisons, forest owners and visitors will have to become accustomed to the fact that their forests must again produce more wood and that, on account of global warming, protective forests will become even more important than they already are today.

SELISIH BIAYA PRODUKSI SEBAGAI ALAT PENGENDALIAN MANAJEMEN PT INDO PUSAKA BERAU

2019 ◽  
Vol 3 (02) ◽  
pp. 397
Author(s):  
SAFITRI NURHIDAYATI ◽  
RIZKI AMELYA SYAM
Keyword(s):  
Raw Materials ◽  
Field Research ◽  
Analytical Tool ◽  
Production Costs ◽  
Raw Material ◽  
Labor Costs ◽  
Material Costs ◽  
Library Research ◽  
The Difference ◽  
The Cost

This study aims to analyze whether the difference that occurs in the cost of raw materials, direct labor, and factory overhead costs between the standard costs and the actual costs in PLTU LATI is a difference that is favorable or unfavorable. Data collection techniques with field research and library research. The analytical tool used is the analysis of the difference in raw material costs, the difference in direct labor costs and the difference in factory overhead costs. The hypothesis in this study is that the difference allegedly occurs in the cost of raw materials, direct labor costs, and factory overhead costs at PT Indo Pusaka Berau Tanjung Redeb is a favorable difference. The results showed that the difference in the cost of producing MWh electricity at PT Indo Pusaka Berau Tanjung Redeb in 2018, namely the difference in the price of raw material costs Rp. 548,029.80, - is favorable, the difference in quantity of raw materials is Rp. 957,216,602, - is (favorable) , the difference in direct labor costs Rp 2,602,642,084, - is (unfavorable), and the difference in factory overhead costs Rp 8,807,051,422, - is (favorable) This shows that the difference in the overall production cost budget is favorable or profitable. This beneficial difference shows that the company is really able to reduce production costs optimally in 2018.  

Technical accounting: sugar extraction and losses

2020 ◽  
pp. 712-721
Author(s):  
Jan Maarten de Bruijn de Bruijn
Keyword(s):  
Process Improvement ◽  
Best Practice ◽  
Continuous Process ◽  
Extraction Yield ◽  
Production Costs ◽  
Raw Material ◽  
Sugar Production ◽  
Cost Leadership ◽  
Sugar Extraction ◽  
White Sugar

The bought sugar in the processed raw material (either beet or cane) comprises a high financial value and may contribute to somewhere around 50% of the white sugar production costs. It is therefore of the utmost importance to minimize sugar losses along the process and produce as much white sugar as possible from the raw material. This paper explains the principle of technical accounting as tool to control sugar extraction and losses in beet sugar manufacture. The sugar mass balance used to calculate the overall sugar extraction yield, as well as several simple calculations proposed for estimating the different sugar losses (like e.g. extraction (diffusion) losses, infection losses, sugar losses in molasses, etc.) in the subsequent process steps will be explained in detail. Proper technical accounting is considered indispensable for continuous process control and process improvement in pursuit of best-practice operation and cost-leadership.

scholarly journals Rheological behavior of high consistency enzymatically fibrillated cellulose suspensions

Cellulose ◽  
2021 ◽  
Author(s):  
Aayush Kumar Jaiswal ◽  
Vinay Kumar ◽  
Alexey Khakalo ◽  
Panu Lahtinen ◽  
Katariina Solin ◽  
...  
Keyword(s):  
Power Law ◽  
Shear Viscosity ◽  
Production Costs ◽  
Raw Material ◽  
Structure Property ◽  
Morphological Examination ◽  
Direct Function ◽  
Typical Application ◽  
Enzyme Dosage ◽  
High Consistency

AbstractHigh-consistency processing of fibrillated cellulose materials is attractive for commercial applications due to potential for lowered production costs, energy savings and easier logistics. The current work investigated structure–property relationships of fibrillated cellulose suspensions produced at 20% consistency using VTT HefCel (High-consistency enzymatic fibrillation of cellulose) technology. Morphological examination of the fibrillated materials revealed that enzymatic action on the cellulose substrates was not a direct function of enzyme dosage but rather was dependent on the raw material composition. Furthermore, shear viscosity of the HefCel suspensions was found to decrease with increasing enzyme dosage while the water retention increased. The shear viscosity followed power law relationship with the power law index varying in the range 0.11–0.73. The shear-thinning behavior decreased with increasing consistency. Moreover, suspension viscosity ($$\upmu$$ μ ) was found to be highly dependent on the consistency ($$\mathrm{c})$$ c ) as $$\upmu \sim {\mathrm{c}}^{\mathrm{m}}$$ μ ∼ c m , with $$\mathrm{m}$$ m ranging from 2.75 to 4.31 for different samples. Yield stress (τy) of the HefCel suspensions was measured at 7 and 10% consistencies. The performance of the fibrillated cellulose grades in a typical application was demonstrated by casting films, which were characterized for their mechanical properties. Graphic abstract

scholarly journals Analysis and Optimization of Two Film-Coated Tablet Production Processes by Computer Simulation: A Case Study

Processes ◽  
2020 ◽  
Vol 9 (1) ◽  
pp. 67
Author(s):  
Stefanie Hering ◽  
Nico Schäuble ◽  
Thomas M. Buck ◽  
Brigitta Loretz ◽  
Thomas Rillmann ◽  
...  
Keyword(s):  
Computer Simulation ◽  
Model Building ◽  
Discrete Event ◽  
Simulation Software ◽  
Labor Costs ◽  
Event Simulation ◽  
Processing Times ◽  
Production Processes ◽  
Coated Tablet ◽  
Pharmaceutical Production

Increasing regulatory demands are forcing the pharmaceutical industry to invest its available resources carefully. This is especially challenging for small- and middle-sized companies. Computer simulation software like FlexSim allows one to explore variations in production processes without the need to interrupt the running process. Here, we applied a discrete-event simulation to two approved film-coated tablet production processes. The simulations were performed with FlexSim (FlexSim Deutschland—Ingenieurbüro für Simulationsdienstleistung Ralf Gruber, Kirchlengern, Germany). Process visualization was done using Cmap Tools (Florida Institute for Human and Machine Cognition, Pensacola, FL, USA), and statistical analysis used MiniTab® (Minitab GmbH, Munich, Germany). The most critical elements identified during model building were the model logic, operating schedule, and processing times. These factors were graphically and statistically verified. To optimize the utilization of employees, three different shift systems were simulated, thereby revealing the advantages of two-shift and one-and-a-half-shift systems compared to a one-shift system. Without the need to interrupt any currently running production processes, we found that changing the shift system could save 50–53% of the campaign duration and 9–14% of the labor costs. In summary, we demonstrated that FlexSim, which is mainly used in logistics, can also be advantageously implemented for modeling and optimizing pharmaceutical production processes.

scholarly journals Economic and Sustainability of Biodiesel Production—A Systematic Literature Review

2021 ◽  
Vol 3 (1) ◽  
pp. 19-36
Author(s):  
Tamás Mizik ◽  
Gábor Gyarmati
Keyword(s):  
Literature Review ◽  
Systematic Literature Review ◽  
Volatile Fatty Acids ◽  
First Generation ◽  
Production Costs ◽  
Raw Material ◽  
Biodiesel Production ◽  
Important Research Topic ◽  
The Social ◽  
High Production

As Earth’s fossil energy resources are limited, there is a growing need for renewable resources such as biodiesel. That is the reason why the social, economic and environmental impacts of biofuels became an important research topic in the last decade. Depleted stocks of crude oil and the significant level of environmental pollution encourage researchers and professionals to seek and find solutions. The study aims to analyze the economic and sustainability issues of biodiesel production by a systematic literature review. During this process, 53 relevant studies were analyzed out of 13,069 identified articles. Every study agrees that there are several concerns about the first-generation technology; however, further generations cannot be price-competitive at this moment due to the immature technology and high production costs. However, there are promising alternatives, such as wastewater-based microalgae with up to 70% oil content, fat, oils and grease (FOG), when production cost is below 799 USD/gallon, and municipal solid waste-volatile fatty acids technology, where the raw material is free. Proper management of the co-products (mainly glycerol) is essential, especially at the currently low petroleum prices (0.29 USD/L), which can only be handled by the biorefineries. Sustainability is sometimes translated as cost efficiency, but the complex interpretation is becoming more common. Common elements of sustainability are environmental and social, as well as economic, issues.

Gula cair dan gula recengan berbahan dasar gula merah tebu

DEDIKASI ◽  
2020 ◽  
Vol 22 (1) ◽  
Author(s):  
M. Yasser ◽  
A.M. Iqbal Akbar Asfar ◽  
Marlia Rianti ◽  
A.M. Irfan Taufan Asfar ◽  
Eko Budianto
Keyword(s):  
Community Service ◽  
Sugar Cane ◽  
Economic Value ◽  
Business Group ◽  
Raw Material ◽  
Community Partnership ◽  
Brown Sugar ◽  
Plastic Packaging ◽  
The Impact ◽  
Partnership Program

This Community Service is a Community Partnership Program that was carried out by to partners of the Brown Sugar Cane Business Group in Latellang Village, Patimpeng District. The processing of sugar cane so far has been very simple, and some of the sugar cane businesses were out of business due to the consumption and need for brown sugar cane by the community, especially the Latellang and other villages, who are reluctant to consume brown sugar cane. This reluctance is caused by the aroma of brown sugar cane. Therefore, diversification of brown sugar cane products was carried out by processing brown sugar cane into Liquid sugar and Recengan sugar. The results of the PKM program were able to provide partners with increased knowledge of processing brown sugar cane into a diversified product that has high economic value and reduced the price of brown sugar cane from Rp. 10,000 per kilogram into products with 250 grams of brown sugar cane as raw material. 2-3 bottles of Liquid Sugar (250 ml plastic packaging) with a price of Rp.10,000 per bottle and produce 15 pieces of Recengan Sugar. Especially for Recengan sugar packaging, it is packaged in pouch containing 8 Recengan sugar ata a price of Rp.10,000. The impact will be revive the production of cane brown sugar to the Cane Brown Sugar Business Group partners, especially in Latellang Village.

Sign in / Sign up

Export Citation Format

Share Document