A Comparative Analysis of Turbine Rotor Inlet Temperature Models

2011 ◽  
Author(s):  
Cristhian Maravilla Herrera ◽  
Sergiy Yepifanov ◽  
Igor Loboda
Keyword(s):  
Gas Turbines ◽  
Thermal State ◽  
Turbine Rotor ◽  
Remaining Useful Life ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Gas Temperature ◽  
Thermal Boundary Conditions ◽  
Power Setting ◽  
Stress Estimation

Life usage algorithms constitute one of the principal components of gas turbine engines monitoring systems. These algorithms aim to determine the remaining useful life of gas turbines based on temperature and stress estimation in critical hot part elements. Knowing temperatures around these elements is therefore very important. This paper deals with blades and disks of a high pressure turbine (HPT). In order to monitor their thermal state, it is necessary to set thermal boundary conditions. The main parameter to determine is the total gas temperature in relative motion at the inlet of HPT blades Tw*. We propose to calculate this unmeasured temperature as a function of measured gas path variables using gas path thermodynamics. Five models with different thermodynamic relations to calculate the temperature Tw* are proposed and compared. All temperature models include some unmeasured parameters that are presented as polynomial functions of a measured power setting variable. A nonlinear thermodynamic model is used to calculate the unknown coefficients included in the polynomials and to validate the models considering the influence of engine deterioration and operating conditions. In the validation stage, the polynomial’s inadequacy and the errors caused by the measurement inaccuracy are analyzed. Finally, the gas temperature models are compared using the criterion of total accuracy and the best model is selected.

A Simple Method for the Prediction of Wall Temperatures in Gas Turbines

1978 ◽  
Author(s):  
D. Kretschmer ◽  
J. Odgers
Keyword(s):  
Film Cooling ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Gas Temperature ◽  
Empirical Formulas ◽  
Simple Method ◽  
Hot Gas ◽  
Manufacturing Tolerances ◽  
Factor Governing

The cited method predicts wall temperatures generally within an accuracy of ± 6 percent, The biggest single factor governing the wall temperature is shown to be the hot gas temperature. Other factors discussed are the effects of changes in inlet temperature, fuel types, the geometry of the film cooling devices and manufacturing tolerances. Empirical formulas are given for the prediction of effective temperatures within the various combustor zones. Some comparisons are made between predictions and measurements of wall temperatures over a range of operating conditions.

Impact of Operating Conditions and Design Parameters on Gas Turbine Hot Section Creep Life

2010 ◽  
Author(s):  
S. Eshati ◽  
M. F. Abdul Ghafir ◽  
P. Laskaridis ◽  
Y. G. Li
Keyword(s):  
Gas Turbines ◽  
Performance Model ◽  
Operating Conditions ◽  
Creep Model ◽  
Design Parameters ◽  
Gas Temperature ◽  
Creep Life ◽  
Cooling Effectiveness ◽  
Radial Temperature ◽  
The Impact

This paper investigates the relationship between design parameters and creep life consumption of stationary gas turbines using a physics based life model. A representative thermodynamic performance model is used to simulate engine performance. The output from the performance model is used as an input to the physics based model. The model consists of blade sizing model which sizes the HPT blade using the constant nozzle method, mechanical stress model which performs the stress analysis, thermal model which performs thermal analysis by considering the radial distribution of gas temperature, and creep model which using the Larson-miller parameter to calculate the lowest blade creep life. The effect of different parameters including radial temperature distortion factor (RTDF), material properties, cooling effectiveness and turbine entry temperatures (TET) is investigated. The results show that different design parameter combined with a change in operating conditions can significantly affect the creep life of the HPT blade and the location along the span of the blade where the failure could occur. Using lower RTDF the lowest creep life is located at the lower section of the span, whereas at higher RTDF the lowest creep life is located at the upper side of the span. It also shows that at different cooling effectiveness and TET for both materials the lowest blade creep life is located between the mid and the tip of the span. The physics based model was found to be simple and useful tool to investigate the impact of the above parameters on creep life.

Experience With Large Heavy-Duty Gas Turbine Rotors

1981 ◽  
Author(s):  
O. R. Schmoch ◽  
B. Deblon
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Turbine Rotor ◽  
Strength Properties ◽  
Operating Conditions ◽  
Material Strength ◽  
Heavy Duty ◽  
Turbine Rotors ◽  
Heavy Duty Gas Turbine ◽  
Response To Temperature

The peripheral speeds of the rotors of large heavy-duty gas turbines have reached levels which place extremely high demands on material strength properties. The particular requirements of gas turbine rotors, as a result of the cycle, operating conditions and the ensuing overall concepts, have led different gas turbine manufacturers to produce special structural designs to resolve these problems. In this connection, a report is given here on a gas turbine rotor consisting of separate discs which are held together by a center bolt and mutually centered by radial serrations in a manner permitting expansion and contraction in response to temperature changges. In particular, the experience gained in the manufacture, operation and servicing are discussed.

Optimisation of CO Turndown for an Axially Staged Gas Turbine Combustor

2020 ◽  
Author(s):  
Jacob E. Rivera ◽  
Robert L. Gordon ◽  
Mohsen Talei ◽  
Gilles Bourque
Keyword(s):  
Residence Time ◽  
Parametric Study ◽  
Gas Turbines ◽  
Flow Reactor ◽  
Operating Conditions ◽  
Independent Effect ◽  
Inlet Temperature ◽  
Operating Characteristics ◽  
Two Stage ◽  
The Impact

Abstract This paper reports on an optimisation study of the CO turndown behaviour of an axially staged combustor, in the context of industrial gas turbines (GT). The aim of this work is to assess the optimally achievable CO turndown behaviour limit given system and operating characteristics, without considering flow-induced behaviours such as mixing quality and flame spatial characteristics. To that end, chemical reactor network modelling is used to investigate the impact of various system and operating conditions on the exhaust CO emissions of each combustion stage, as well as at the combustor exit. Different combustor residence time combinations are explored to determine their contribution to the exhaust CO emissions. The two-stage combustor modelled in this study consists of a primary (Py) and a secondary (Sy) combustion stage, followed by a discharge nozzle (DN), which distributes the exhaust to the turbines. The Py is modelled using a freely propagating flame (FPF), with the exhaust gas extracted downstream of the flame front at a specific location corresponding to a specified residence time (tr). These exhaust gases are then mixed and combusted with fresh gases in the Sy, modelled by a perfectly stirred reactor (PSR) operating within a set tr. These combined gases then flow into the DN, which is modelled by a plug flow reactor (PFR) that cools the gas to varying combustor exit temperatures within a constrained tr. Together, these form a simplified CRN model of a two-stage, dry-low emissions (DLE) combustion system. Using this CRN model, the impact of the tr distribution between the Py, Sy and DN is explored. A parametric study is conducted to determine how inlet pressure (Pin), inlet temperature (Tin), equivalence ratio (ϕ) and Py-Sy fuel split (FS), individually impact indicative CO turndown behaviour. Their coupling throughout engine load is then investigated using a model combustor, and its effect on CO turndown is explored. Thus, this aims to deduce the fundamental, chemically-driven parameters considered to be most important for identifying the optimal CO turndown of GT combustors. In this work, a parametric study and a model combustor study are presented. The parametric study consists of changing a single parameter at a time, to observe the independent effect of this change and determine its contribution to CO turndown behaviour. The model combustor study uses the same CRN, and varies the parameters simultaneously to mimic their change as an engine moves through its steady-state power curve. The latter study thus elucidates the difference in CO turndown behaviour when all operating conditions are coupled, as they are in practical engines. The results of this study aim to demonstrate the parameters that are key for optimising and improving CO turndown.

Principles of Imitation for the Loading of the Test Bench for Gas Turbines of Gas Pumping Units, Adequate to Real Conditions

2021 ◽  
Vol 13 (24) ◽  
pp. 13678
Author(s):  
Anton Petrochenkov ◽  
Aleksandr Romodin ◽  
Vladimir Kazantsev ◽  
Aleksey Sal’nikov ◽  
Sergey Bochkarev ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Simulation Models ◽  
Turbine Rotor ◽  
Operating Conditions ◽  
Automation System ◽  
Model Free ◽  
Gas Pumping ◽  
Pumping Units

The purpose of the study is to analyze the prospects for the development of loading methods for gas turbines as well as to develop a mathematical model that adequately describes the real operating conditions of the loading system at various loads and rotation speeds. A comparative analysis of the most common methods and technical means of loading the shafts of a free turbine at gas turbine plants intended for operation as part of gas pumping units is presented. Based on the results of the analysis, the expediency of using the loading model “Free Power Turbine Rotor–Hydraulic Brake” as a load simulation is shown. Recommendations for the creation of an automation system for the load testing of power plants have been developed. Mathematical models and Hardware-in-the-Loop simulation models of power plants have been developed and tested. One of the most important factors that predetermine the effectiveness of the loading principle is the possibility of software implementation of the loading means using software control systems that provide the specified loading parameters of the gas turbine.

Experimental and Computational Analysis of Additive Manufactured Augmented Backside Liner Cooling Surfaces for Use in Micro Gas Turbines

2020 ◽  
Author(s):  
Adamos Adamou ◽  
Colin Copeland
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Gas Turbines ◽  
Conjugate Heat Transfer ◽  
Reverse Flow ◽  
Operating Conditions ◽  
Experimental Results ◽  
Gas Temperature ◽  
Cfd Models ◽  
High Heat Transfer

Abstract Augmented backside cooling refers to the enhancement of the backside convection of a combustor liner using extended heat transfer surfaces to fully utilise the cooling air by maximising the heat transfer to pumping ratio characteristic. Although film cooling has and still is widely used in the gas turbine industry, augmented backside cooling has been in development for decades now. The reason for this, is to reduce the amount of air used for liner cooling and to also reduce the emissions caused by using film cooling in the primary zones. In the case of micro gas turbines, emissions are of even greater importance, since the regulations for such engines will most likely become stricter in the following years due to a global effort to reduce emission. Furthermore, the liners investigated in this paper are for a 10 kWe micro turbine, destine for various potential markets, such as combine heat and power for houses, EV hybrids and even small UAVs. The majority of these markets require long service intervals, which in turn requires the combustor liners to be under the least amount of thermal stress possible. The desire to also increase combustor inlet temperatures with the use of recuperated exhaust gases, which in turn increase the overall system efficiency, limits the cooling effectiveness of the inlet air. Due to all these reasons, an advanced form of augmented backside cooling would be of substantial significance in such a system. Currently some very simple designs are used in the form of straight plain fins, transverse strips or other similar geometries, but the creation of high heat transfer efficiency surfaces in such small sizes becomes very difficult with traditional subtractive manufacturing methods. When using additive manufacturing though these types of surfaces are not an issue. This paper covers the comparison of experimental results with conjugate heat transfer CFD models and empirical heat balance models for two different AM liner cooling geometries and an AM blank liner. The two cooling fin geometries include a rotating plain fin and an offset strip fin. The liners were tested in an AM built reverse flow radial swirl stabilised combustion chamber at a variety of operating conditions. During the experiments the surfaces were compared using a thermal camera to record the outer liner temperature which was viewed through a quartz outer casing. The experimental results showed that the cooling surfaces were effective at reducing the liner temperatures with minimal pressure losses for multiple operating points. Those results were then compared against the conjugate heat transfer CFD models and the empirical calculations used to design the surfaces initially. From this comparison, it was noticed both the CFD and empirical calculations under predicted the wall temperatures. This is thought to be due to inaccuracies in the predicted flame temperatures and the assumed emissivity values used to calibrate the thermal imaging camera. Further uncertainties arise from the assumption of a constant air and hot gas temperature and mass flow along the cooling surfaces and the lack of data for the surface roughness of the parts.

Application of Ultra-Low NOx Combustor to the MHPS Existing Gas Turbine

2021 ◽  
Author(s):  
Takashi Nishiumi ◽  
Hirofumi Ohara ◽  
Kotaro Miyauchi ◽  
Sosuke Nakamura ◽  
Toshishige Ai ◽  
...  
Keyword(s):  
High Pressure ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Operational Experience ◽  
Emission Rates ◽  
Gas Temperature ◽  
Design Development ◽  
And Control

Abstract In recent years, MHPS achieved a NET M501J gas turbine combined cycle (GTCC) efficiency in excess of 62% operating at 1,600°C, while maintaining NOx under 25ppm. Taking advantage of our gas turbine combustion design, development and operational experience, retrofits of earlier generation gas turbines have been successfully applied and will be described in this paper. One example of the latest J-Series technologies, a conventional pilot nozzle was changed to a premix type pilot nozzle for low emission. The technology was retrofitted to the existing F-Series gas turbines, which resulted in emission rates of lower than 9ppm NOx(15%O2) while maintaining the same Turbine Inlet Temperature (TIT: Average Gas Temperature at the exit of the transition piece). After performing retrofitting design, high pressure rig tests, the field test prior to commercial operation was conducted on January 2019. This paper describes the Ultra-Low NOx combustor design features, retrofit design, high pressure rig test and verification test results of the upgraded M501F gas turbine. In addition, it describes another upgrade of turbine to improve efficiency and of combustion control system to achieve low emissions. Furthermore it describes the trouble-free upgrade of seven (7) units, which was completed by utilizing MHPS integration capabilities, including handling all the design, construction and service work of the main equipment, plant and control systems.

Oxidation Behavior of LTA/YSZ Intermixed Layer Coating

2018 ◽  
pp. 107-130
Author(s):  
Pritee Purohit ◽  
Shashikant T. Vagge
Keyword(s):  
Gas Turbines ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Power Generators ◽  
Industrial Gas Turbines ◽  
The Mean ◽  
Aero Engines ◽  
Industrial Gas Turbine ◽  
Day By Day ◽  
Very High

This chapter describes how for power generators like gas turbines and aero engines, the economic and environmental challenges are increasing day by day for producing electricity more efficiently. The efficiency of power generators can be increased by changing its operating conditions like inlet temperature and procedure. Currently, the inlet temperature to the industrial gas turbine is reaching up to 1400°C. Also, in aero engines, the ring temperature reaches around 1550°C. Therefore, the coatings used in aero engine applications undergo short duration thermal cycles at very high temperature. The mean metal temperatures reach around 950°C and can increase up to 1100°C. But in industrial gas turbines, it varies from 800 to 950°C. Operating temperature of industrial gas turbines slowly reaches to maximum and ideally remains constant for thousands of hours, unlike aero engines.

Micro Gas Turbine With Ceramic Nozzle and Rotor

2005 ◽  
Author(s):  
Takayuki Matsunuma ◽  
Hiro Yoshida ◽  
Norihiko Iki ◽  
Takumi Ebara ◽  
Satoshi Sodeoka ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Turbine Rotor ◽  
Total Power ◽  
Inlet Temperature ◽  
Present System ◽  
Outlet Temperature ◽  
Micro Gas Turbine ◽  
Buffer Material ◽  
Inconel 713C

A series of operation tests of a ceramic micro gas turbine has been successfully carried out. The baseline machine is a small single-shaft turbojet engine (J-850, Sophia Precision Corp.) with a centrifugal compressor, an annular type combustor, and a radial turbine. As a first step, an Inconel 713C alloy turbine rotor of 55 mm in diameter was replaced with a ceramic rotor (SN-235, Kyocera Corporation). A running test was conducted at rotational speeds of up to 140,000 rpm in atmospheric air. At this rotor speed, the compression pressure ratio and the thrust were 3 and 100 N, respectively. The total energy level (enthalpy and kinetic energy) of the exhaust gas jet was 240 kW. If, for example, it is assumed that 10% of the total power of the exhaust jet gas was converted into electricity, the present system would correspond to a generator with 24 kW output power. The measured turbine outlet temperature was 950°C (1,740°F) and the turbine inlet temperature was estimated to be 1,280°C (2,340°F). Although the ceramic rotor showed no evidence of degradation, the Inconel nozzle immediately in front of the turbine rotor partially melted in this rotor condition. As a second step, the Inconel turbine nozzle and casing were replaced with ceramic parts (SN-01, Ohtsuka Ceramics Inc.). The ceramic nozzle and case were supported by metal parts. Through tests with the ceramic nozzle, it became evident that one of the key technologies for the development of ceramic gas turbines is the design of the interface between the ceramic components and the metallic components, because the difference between the coefficients of linear thermal expansion of the ceramic and metal produces large thermal stress at their interface in the high-temperature condition. A buffer material made of alumina fiber was therefore introduced at the interface between the ceramic and metal.

scholarly journals Status of the Automotive Ceramic Gas Turbine Development Program: Year 3 Progress

1994 ◽  
Author(s):  
Takane Itoh ◽  
Hidetomo Kimura
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Performance Test ◽  
Development Program ◽  
Turbine Rotor ◽  
Maximum Speed ◽  
Inlet Temperature ◽  
Test Rig ◽  
Thermal Test ◽  
The Individual

Under the ongoing seven-year program, designated “Research and Development of Automotive Ceramic Gas Turbine Engine (CGT Program)”, started in June 1990. Japan Automobile Research Institute. Inc. (JARI) is continuing to address the issues of developing and demonstrating the advantageous potentials of ceramic gas turbines for automotive use. This program has been conducted by the Petroleum Energy Center (PEC) with the financial support of MITI. The basic engine is a 100 kW, single-shaft regenerative engine having a turbine inlet temperature of 1350°C and a rotor speed of 110,000 rpm. In the third year of this program, the experimental evaluation of the individual engine components and various assembly tests in a static thermal test rig were continued. Exhaust emissions were also measured in a performance test rig for an initially designed pre-mixed, pre-vaporized lean (PPL) combustor. A maximum speed of 130,700 rpm was obtained during hot spin tests of delivered ceramic turbine rotors, which was almost the same level as during cold spin tests. A dynamic thermal test including a centrifugal compressor, a ceramic radial turbine rotor and all the ceramic stationary hot parts was initiated.

Sign in / Sign up

Export Citation Format

Share Document