Effects of Curvature on the Film Cooling Effectiveness of Double-Jet Film Cooling

2014 ◽  
Author(s):  
Gaoliang Liao ◽  
Xinjun Wang ◽  
Jun Li ◽  
Feng Zhang
Keyword(s):  
Film Cooling ◽  
Flat Surface ◽  
Three Dimensional ◽  
Curved Surface ◽  
Navier Stokes ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Injection Angle ◽  
Sst Model ◽  
Selection Of

The effect of curvature on the film cooling characteristics of Double-Jet Film Cooling (DJFC) was numerically investigated using three-dimensional Reynolds-Averaged Navier-Stokes (RANS). The low-Reynolds number shear stress transport (SST) model was employed as the turbulence closure model. Six different curved surfaces and a flat surface were tested numerically. The blowing ratios were from 0.66 to 1.99, and the compound injection angle with respect to the cooled surface was 30 degree. The blowing ratios and the curvature of cooled surface have crucial effects on the film cooling effectiveness. The numerical results show that there are two peek value of the averaged film cooling effectiveness along the mainstream direction. The results also indicate that the film cooling effectiveness of a specified curved surface depends on the reasonable selection of the slope of curved surface and blowing ratios.

Systematic Study of Film Cooling With a Three-Dimensional Calculation Procedure

1986 ◽  
Vol 108 (1) ◽  
pp. 124-130 ◽  
Author(s):  
A. O. Demuren ◽  
W. Rodi ◽  
B. Scho¨nung
Keyword(s):  
Systematic Study ◽  
Film Cooling ◽  
Three Dimensional ◽  
Heat Fluxes ◽  
Test Cases ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Injection Angle ◽  
The Individual ◽  
Volume Method

The present paper describes three-dimensional calculations of film cooling by injection from a single row of holes. A systematic study of the influence of different parameters on the cooling effectiveness has been carried out. Twenty-seven test cases have been calculated, varying the injection angle (α = 10/45/90 deg), the relative spacing (s/D = 1.5/3/5) and the blowing rate (M = 0.5/1/2) for the same mainstream conditions. The governing three-dimensional equations are solved by a finite volume method. The turbulent stresses and heat fluxes are obtained from a k–ε model modified to account for nonisotropic eddy viscosities and diffusivities. Examples of predicted velocity and temperature distributions are presented and compared with available experimental data. For all the test cases, the laterally averaged cooling effectiveness is given. On the whole, the agreement with experiments is fairly good, even though there are discrepancies about details in some of the cases. The influence of the individual parameters on the film cooling effectiveness is predicted correctly in all cases. This influence is discussed in some detail and the parameter combination with the best overall cooling performance is identified.

Analyzes of Film Cooling Effectiveness from Cylindrical and Staggered Compound Cooling Holes with Alignment Angle of 30 Degree at the End of Combustor

2014 ◽  
Vol 695 ◽  
pp. 389-392
Author(s):  
Shahin Salimi ◽  
Nor Azwadi Che Sidik ◽  
Leila Jahanshaloo ◽  
Kianpour Ehsan
Keyword(s):  
Film Cooling ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Internal Cooling ◽  
Ansys Fluent ◽  
Cooling Effectiveness ◽  
Turbine Engine ◽  
Film Cooling Effectiveness ◽  
Alignment Angle ◽  
Compound Angle

A numerical simulation has been performed for the investigation of flow and heat transfer characteristics of a film cooling injected through a hole with cylindrical and compound angle orientation. This paper presents the effects of coolant injector configuration of cylindrical and compound cooling holes with alignment angle of 30 degree at blowing ratio, BR = 3.18 on the film cooling effectiveness near the end wall surface of a combustor simulator. In the current research a three dimensional representation of Pratt and Whitney gas turbine engine was simulated and analyzed with a commercial finite volume package ANSYS FLUENT 14.0. This study has been performed with Reynolds-averaged Navier-Stokes turbulence model (RANS) on internal cooling passages The results indicate that using compound angle cooling holes injection, give much better protection than that obtained when simple angle cooling holes were used.

Optimization of a Fan-Shaped Hole for Film Cooling Using a Surrogate Model

2009 ◽  
Author(s):  
Ki-Don Lee ◽  
Kwang-Yong Kim
Keyword(s):  
Film Cooling ◽  
Three Dimensional ◽  
Numerical Procedure ◽  
Latin Hypercube Sampling ◽  
Optimal Point ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Injection Angle ◽  
Design Variables ◽  
Shaped Hole

A numerical procedure for shape optimization of a fan-shaped hole is presented to enhance film-cooling effectiveness by combining a three-dimensional Reynolds-averaged Navier-Stokes analysis with the radial neural network method, a well known surrogate modeling technique for optimization. The injection angle of the hole, lateral expansion angle of hole and ratio of length-to-diameter of the hole are chosen as design variables and spatially averaged film-cooling effectiveness is considered as an objective function which is to be maximized. Latin hypercube sampling is used to determine the training points as a mean of the design of experiment. Sequential quadratic programming is used to search for the optimal point from the constructed surrogate. The film-cooling effectiveness has been successfully improved by the optimization with increased values of all design variables as compared to the reference geometry.

Effect of Various Injection Hole Shapes on Film Cooling of Turbine Blade

2003 ◽  
Author(s):  
S.-M. Kim ◽  
Youn J. Kim
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Three Dimensional ◽  
Cylindrical Body ◽  
Navier Stokes ◽  
Cylinder Surface ◽  
Injection Hole ◽  
Film Cooling Effectiveness ◽  
Injection Angle ◽  
Cooling Flow

Dispersion of coolant jets in a film cooling flow field is the result of a highly complex interaction between the film cooling jets and the mainstream. In order to investigate the effects of injection hole shapes and injection angle on the film cooling of turbine blade, four models having cylindrical and laterally-diffused holes were used. Three-dimensional Navier-Stokes code with k – ε model was used to compute the film cooling coefficient on the turbine blade. A multi-block grid system was generated that was nearly orthogonal to the various surfaces. Mainstream Reynolds number based on the cylinder diameter was 7.1 × 104. The turbulence intensity kept at 5.0% for all inlets. The effect of coolant flow rates was studied for blowing ratios of 0.9, 1.3 and 1.6, respectively. The temperature distribution of the cylindrical body surface is visualized by infrared thermography (IRT) and compared with computational results. Results show that the effects of injection hole shape and injection angle increase as the blowing ratio increases. As lateral injection angle increases, the adiabatic film cooling effectiveness is more broadly distributed and the area protected by coolant increases. The mass flow rate of the coolant through the first-row holes is less than that through the second-row holes due to the pressure distribution around the cylinder surface.

Numerical Investigation of Scoop Effect on Film Cooling for Cylindrical Inclined Hole

2017 ◽  
Author(s):  
Yongbin Ji ◽  
Prashant Singh ◽  
Srinath V. Ekkad ◽  
Shusheng Zhang
Keyword(s):  
Film Cooling ◽  
Three Dimensional ◽  
Diameter Ratio ◽  
Navier Stokes ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Sst Turbulence Model ◽  
Cooling Behavior ◽  
Length To Diameter Ratio

Film cooling behavior of a single cylindrical hole inclined at an angle of 35° with respect to a flat surface is numerically predicted in this study. Adiabatic film cooling effectiveness has been presented to evaluate the influence of the scoop placed on the coolant entry side. The effect of blowing ratio (0.65, 1, 1.5 and 2) and the length-to-diameter ratio (1.7 and 4.4) are examined. Three-dimensional Reynolds-averaged Navier-Stokes analysis with SST turbulence model is used for the computations. It has been found that both centerline and laterally averaged adiabatic film cooling effectiveness are enhanced by the scoop and the enhancement increases with the blowing ratio in the investigated range of variables. The scoop was more effective for the higher length-to-diameter ratio cases (L/D = 4.4) because of better velocity distribution at the film hole exit, which makes coolant reattach at a more upstream location after blowing off from the wall.

Enhancement of Film Cooling Effectiveness Using Rectangular Winglet Pair

2018 ◽  
Vol 10 (4) ◽  
Author(s):  
Prakhar Jindal ◽  
Shubham Agarwal ◽  
R. P. Sharma ◽  
A. K. Roy
Keyword(s):  
Film Cooling ◽  
Complete Solution ◽  
Three Dimensional ◽  
Numerical Approach ◽  
Navier Stokes ◽  
Geometrical Parameters ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Enhancement ◽  
The Common

This study deals with the film cooling enhancement in a combustion chamber by the use of rectangular winglet vortex generators (VGs). Rectangular winglet pair (RWP) in both the common-flow up and the common-flow down configuration is installed upstream of a coolant injection hole on the lower chamber wall. A three-dimensional numerical approach with complete solution of Navier–Stokes (NS) equations closed by the k–ɛ turbulence model is used for analyzing the effect of VG installation on film cooling effectiveness enhancement. The effect of RWP orientation is investigated to deduce the best configuration which is then optimized in terms of its geometrical parameters including its upstream distance from the hole and the angle it makes with the incoming flow. Results obtained show that a RWP located upstream of the coolant hole in common-flow down configuration gives the best effectiveness enhancement with certain other geometrical parameters specified. A novel “mushroom” adiabatic distribution scheme for film cooling effectiveness and temperature has been discussed in the paper. This characteristic scheme is developed as a result of RWPs' vortices interaction with the coolant inlet jet and the hot mainstream flow. A detailed discussion of the mechanisms and the flow field properties underlying the effectiveness enhancement and other phenomenon observed has also been presented in the paper.

Numerical Study on Film-Cooling Effectiveness for Various Film-Cooling Hole Schemes

2011 ◽  
Author(s):  
Sun-min Kim ◽  
Ki-Don Lee ◽  
Kwang-Yong Kim
Keyword(s):  
Film Cooling ◽  
Numerical Study ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Navier Stokes ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Cooling Hole ◽  
Influential Parameters

Film-cooling has been widely used as the important alternative to protect the turbine blade. Since the film-cooling hole geometry is one of the most influential parameters for film-cooling performance, various film-cooling hole schemes have been developed to increase cooling performance for the past few decades. In the present work, numerical analysis has been performed to investigate and to compare the film-cooling performance of various film-cooling hole schemes such as fan-shaped, crescent, louver, and dumbbell holes. For analyzes of the turbulent flow and film-cooling, three-dimensional Reynolds-averaged Navier-Stokes analysis has been performed with shear stress transport turbulence model. The validation of numerical results has been performed in comparison with experimental data. The flow characteristics and film-cooling performance for each hole shape have been investigated and evaluated in terms of local- and averaged film-cooling effectivenesses.

Improvement in Film Cooling Effectiveness Using Single and Double Rows of Holes With Adverse Compound Angle Orientations

2018 ◽  
Vol 11 (2) ◽  
Author(s):  
E. Kannan ◽  
Seralathan Sivamani ◽  
D. G. Roychowdhury ◽  
T. Micha Premkumar ◽  
V. Hariram
Keyword(s):  
Film Cooling ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Cylindrical Hole ◽  
Navier Stokes ◽  
Cooling Effectiveness ◽  
Navier Stokes Equations ◽  
Film Cooling Effectiveness ◽  
Turbine Blade Cooling ◽  
Compound Angle

Abstract Three-dimensional Reynolds-averaged Navier–Stokes equations with shear stress transport turbulence model are used to analyze the film cooling effectiveness on a flat plate having single row of film hole involving cylindrical hole (CH) and laidback hole (LBH). The CH and LBH are inclined at 35 deg to the surface with a compound angle (β) orientation ranging from favorable to adverse inclination (i.e., β = 0–180 deg) and examined at high and low blowing ratios (M = 1.25 and 0.60). CH with an adverse compound angle of 135 deg gives the highest area-averaged film cooling effectiveness in comparison with LBH configuration. Also, CH β = 135 deg film hole shows a higher lateral coolant spread. Later, double jet film cooling (DJFC) concept is studied for this CH. In all the cases, the first hole compound angle is fixed as 135 deg, and the second hole angle is varied from 135 deg to 315 deg. At high blowing ratio, the dual jet cylindrical hole (DJCH) with β = 135 deg, 315 deg gives a higher area-averaged film cooling effectiveness by around 66.50% compared to baseline CH β = 0 deg. On comparing all CH, LBH, and DJCH cases, the highest area-averaged film cooling effectiveness is obtained by CH configuration with β = 135 deg. Hence, the CH with its adverse compound angle (β = 135 deg) orientation could be an appropriate film cooling configuration for gas turbine blade cooling.

scholarly journals Systematic Study of Film Cooling With a Three-Dimensional Calculation Procedure

1985 ◽  
Author(s):  
A. O. Demuren ◽  
W. Rodi ◽  
B. Schönung
Keyword(s):  
Systematic Study ◽  
Film Cooling ◽  
Three Dimensional ◽  
Heat Fluxes ◽  
Main Stream ◽  
Test Cases ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Injection Angle ◽  
The Individual

The present paper describes three-dimensional calculations of film cooling by injection from a single row of holes. A systematic study of the influence of different parameters on the cooling effectiveness has been carried out. 27 test cases have been calculated, varying the injection angle (α = 10° / 45° / 90°), the relative spacing (s/D = 1.5/3/5) and the blowing rate (M = 0.5/1/2) for the same main-stream conditions. The governing 3D equations are solved by a finite volume method. The turbulent stresses and heat fluxes are obtained from a k-ε model modified to account for non-isotropic eddy viscosities and diffusivities. Examples of predicted velocity and temperature distributions are presented and compared with available experimental data. For all the test cases, the laterally averaged cooling effectiveness is given. On the whole, the agreement with experiments is fairly good, even though there are discrepancies about details in some of the cases. The influence of the individual parameters on the film cooling effectiveness is predicted correctly in all cases. This influence is discussed in some detail and the parameter combination with the best overall cooling performance is identified.

Sign in / Sign up

Export Citation Format

Share Document