scholarly journals Microphones and Knock Sensors for Feedback Control of HCCI Engines

2004 ◽  
Author(s):  
Jason S. Souder ◽  
J. Hunter Mack ◽  
J. Karl Hedrick ◽  
Robert W. Dibble
Keyword(s):  
Fuel Injection ◽  
Compression Ignition ◽  
Cylinder Pressure ◽  
Indirect Methods ◽  
Loop Control ◽  
Hcci Engine ◽  
Hcci Engines ◽  
Timing Data ◽  
Knock Sensor ◽  
Direct Fuel Injection

Homogeneous charge compression ignition (HCCI) engines lack direct in-cylinder mechanisms, such as spark plugs or direct fuel injection, for controlling the combustion timing. Many indirect methods have been used to control the combustion timing in a HCCI engine. With any indirect method, it is important to have a measure of the combustion timing so the control inputs can be adjusted for the next cycle. In this paper, it is shown that microphones and knock sensors can be used to detect combustion in HCCI engines. The output from various microphones and a knock sensor on an HCCI engine are measured at light and high loads. The combustion timing data obtained from the sensors are compared to the combustion timing data obtained from a piezoelectric cylinder pressure transducer. One of these sensors is selected and used for closed-loop control of the combustion timing in a single cylinder HCCI engine.

scholarly journals Impact of injection strategies on combustion characteristics, efficiency and emissions of gasoline compression ignition operation in a heavy-duty multi-cylinder engine

2018 ◽  
Vol 21 (8) ◽  
pp. 1426-1440 ◽  
Author(s):  
Buyu Wang ◽  
Michael Pamminger ◽  
Ryan Vojtech ◽  
Thomas Wallner
Keyword(s):  
High Temperature ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Pressure Rise ◽  
Pilot Injection ◽  
Low Temperature Combustion ◽  
Compression Ignition ◽  
Temperature Combustion ◽  
Gas Recirculation ◽  
Direct Fuel Injection

Gasoline compression ignition using a single gasoline-type fuel for direct/port injection has been shown as a method to achieve low-temperature combustion with low engine-out NOx and soot emissions and high indicated thermal efficiency. However, key technical barriers to achieving low-temperature combustion on multi-cylinder engines include the air handling system (limited amount of exhaust gas recirculation) as well as mechanical engine limitations (e.g. peak pressure rise rate). In light of these limitations, high-temperature combustion with reduced amounts of exhaust gas recirculation appears more practical. Furthermore, for high-temperature gasoline compression ignition, an effective aftertreatment system allows high thermal efficiency with low tailpipe-out emissions. In this work, experimental testing was conducted on a 12.4 L multi-cylinder heavy-duty diesel engine operating with high-temperature gasoline compression ignition combustion with port and direct injection. Engine testing was conducted at an engine speed of 1038 r/min and brake mean effective pressure of 1.4 MPa for three injection strategies, late pilot injection, early pilot injection, and port/direct fuel injection. The impact on engine performance and emissions with respect to varying the combustion phasing were quantified within this study. At the same combustion phasing, early pilot injection and port/direct fuel injection had an earlier start of combustion and higher maximum pressure rise rates than late pilot injection attributable to more premixed fuel from pilot or port injection; however, brake thermal efficiencies were higher with late pilot injection due to reduced heat transfer. Early pilot injection also exhibited the highest cylinder-to-cylinder variations due to differences in injector behavior as well as the spray/wall interactions affecting mixing and evaporation process. Overall, peak brake thermal efficiency of 46.1% and 46% for late pilot injection and port/direct fuel injection was achieved comparable to diesel baseline (45.9%), while early pilot injection showed the lowest brake thermal efficiency (45.3%).

Experimental and Numerical Analysis on the Influences of Direct Fuel Injection into Oxygen-Depleted Environment of a Homogeneous Charge Compression Ignition Engine

2021 ◽  
pp. 1-29
Author(s):  
Ratnak Sok ◽  
Kei Yoshimura ◽  
Kenjiro Nakama ◽  
Jin Kusaka
Keyword(s):  
Homogeneous Charge Compression Ignition ◽  
Fuel Injection ◽  
Double Pulse ◽  
Gasoline Direct Injection ◽  
Oh Radicals ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Intake Stroke ◽  
Direct Fuel Injection ◽  
Homogeneous Charge

Abstract The oxygen-depleted environment in the recompression stroke can convert gasoline fuel into light hydrocarbons due to thermal cracking, partial oxidation, and water-gas shift reactions. These reformate species can influence the combustion characteristics of gasoline direct injection homogeneous charge compression ignition (GDI-HCCI) engines. In this work, the combustion phenomena are investigated using a single-cylinder research engine under a medium load. The main combustion phases are experimentally advanced by direct fuel injection into the negative valve overlap (NVO) compared with that of intake stroke under single/double pulse injections. NVO peak in-cylinder pressures are lower than that of motoring due to the limited O2 concentration, emphasizing that endothermic reactions occur during the overlap. This phenomenon limits the oxidation reactions, and the thermal effect is not pronounced. The 0-D chemical kinetics results present the same increasing tendencies of classical reformed species of rich-mixture such as C3H6, C2H4, CH4, CO, and H2 as functions of injection timings. Predicted ignition delays are shortened due to the additions of these reformed species. The influences of the reformates on the main combustion are confirmed by 3-D CFD calculations, and the results show that OH radicals are advanced under NVO injections relative to intake stroke injections. Consequently, earlier heat release and cylinder pressure are noticeable. Parametric studies on the effects of injection pressure, double-pulse injection, and equivalence ratio on the combustion and emissions are also discussed experimentally.

scholarly journals Performance and Emission Characteristics of Homogeneous Charge Compression Ignition Engine with Different Bio Diesel Fuels

2018 ◽  
Vol 7 (4.24) ◽  
pp. 157 ◽  
Author(s):  
P Moulali ◽  
T H Prasad ◽  
B D Prasad
Keyword(s):  
Homogeneous Charge Compression Ignition ◽  
Fuel Injection ◽  
Emission Characteristics ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Hcci Engine ◽  
Diesel Fuels ◽  
Port Fuel Injection ◽  
Mixture Preparation ◽  
Algae Oil

In this paper the emission characteristics and performance of various bio diesel fuels (Tyre pyrolysis oil (TPO), Micro algae oil and Pig animal fat oil) were experimented. A single cylinder, water cooled diesel engine was modified in to homogeneous charge compression ignition engine (HCCI) with adopted port fuel injection (PFI) technique. The effects of air fuel ratio, intake temperature, injection pressure and EGR rate exhaust emissions were explained in a broad manner. The analysis of the exhaust emissions are integrated to oxides of Nitrogen (NOx), Carbon Monoxide (CO), unburned hydro carbons (UHC), smoke and soot. The performance analysis was also included on specific fuel consumption and break thermal efficiency. The basic requirements for HCCI engine is the homogeneous mixture preparation of air and fuel. This mixture formation was done by adopting port fuel injection technique and external devices were also used for bio diesel vaporization and mixture preparation. The combustion processes were measured with different EGR system.  The experimental results of different bio diesel fuels with HCCI engine mode were recorded and evaluated. A small increase in CO and HC emissions were observed with increasing bio diesel content due to slow evaporation rate of bio diesel. A significant reduction in NOx emission was also observed with respect to difference in bio diesel blends. Micro algae oil was found more stable compared with other bio diesel fuels due to the property of fuel vaporization and low heat releasing.

scholarly journals Real-Time Monitoring of Combustion Instability in a Homogeneous Charge Compression Ignition (HCCI) Engine Using Cycle-by-Cycle Exhaust Temperature Measurements

2012 ◽  
Author(s):  
David P. Gardiner ◽  
W. Stuart Neill ◽  
Wallace L. Chippior
Keyword(s):  
Real Time ◽  
Fuel Injection ◽  
Combustion Instability ◽  
Temperature Measurements ◽  
Cylinder Pressure ◽  
Hcci Engine ◽  
Exhaust Temperature ◽  
Indicated Mean Effective Pressure ◽  
Test Engine ◽  
Reference Measurements

This paper describes an experimental study concerning the feasibility of monitoring the combustion instability levels of an HCCI engine based upon cycle-by-cycle exhaust temperature measurements. The test engine was a single cylinder, four-stroke, variable compression ratio Cooperative Fuel Research (CFR) engine coupled to an eddy current dynamometer. A rugged exhaust temperature sensor equipped with special signal processing circuitry was installed near the engine exhaust port. Reference measurements were provided by a laboratory grade, water-cooled cylinder pressure transducer. The cylinder pressure measurements were used to calculate the Coefficient of Variation of Indicated Mean Effective Pressure (COV of IMEP) for each operating condition tested. Experiments with the HCCI engine confirmed that cycle-by-cycle variations in exhaust temperature were present, and were of sufficient magnitude to be captured for processing as high fidelity signal waveforms. There was a good correlation between the variability of the exhaust temperature signal and the COV of IMEP throughout the operating range that was evaluated. The correlation was particularly strong at the low levels of COV of IMEP (2–3%), where production engines would typically operate. A real-time combustion instability signal was obtained from cycle-by-cycle exhaust temperature measurements, and used to provide feedback to the fuel injection control system. Closed loop operation of the HCCI engine was achieved in which the engine was operated as lean as possible while maintaining the COV level at or near 2.5%.

scholarly journals Effect of port injection pressure on mixture quality in Homogeneous charges compression ignition (HCCI) engine

2021 ◽  
Vol 9 (2) ◽  
pp. 37-41
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Injection Pressure ◽  
The Other ◽  
Emission Characteristics ◽  
Compression Ignition ◽  
Fuel Injector ◽  
Compression Ignition Engine ◽  
Hcci Engine ◽  
Fuel Injection Pressure

The purpose of this study is to investigate the effect of fuelinjection pressure onhomogeneous charge formation and performanceand emission characteristics of Homogeneous charge compression ignition engine. The fuel injection pressure isone of the primary parameter for improvingthe homogeneity of the mixture and governing the power output and emission characteristics of HCCI engine. In this investigation, diesel fuelwasinjected at different injection pressuresas 2bar, 3bar, 4bar and 5bar respectively throughbyport fuel injector. The experimental investigationsshow that increasing the fuel injection pressure will promote the fuel to penetrate with air and creates well pre mixedair/fuel charge.The result shows, the specific fuel consumption (SFC) of HCCI engine isslightlyhigherthan the SFC of conventional diesel engine.The HCCI engine with 3bar injection pressure operated engine has lower SFC values compared to other injection pressure operated HCCI engine.The brake thermal efficiency of HCCI engine, operated with 3barinjection pressure has maximum BTE values over the other injection pressure operated engine.From theresult, it is observed that HCCI engine has lower smoke density values compared to conventional diesel engine andfurther reducedby increasing the fuel injection pressure. The 3bar injection pressure operated HCCI engine has emitted lower smoke densitycompared to other injection pressure operated HCCI engine. The 3bar injection pressureoperated HCCIengine hasemittedmaximum oxides of nitrogen (NOx) emissions than the other injection pressure operated HCCI engine. Other exhaust emissions of carbon monoxide (CO) and hydrocarbon (HC)emissions are increased when compared toconvention diesel engine

scholarly journals Numerical investigation into the effect of direct fuel injection on thermal stratification in HCCI engine

2017 ◽  
Vol 169 (2) ◽  
pp. 137-140
Author(s):  
Michał GĘCA ◽  
Jacek HUNICZ ◽  
Piotr JAWORSKI
Keyword(s):  
Combustion Chamber ◽  
Thermal Stratification ◽  
Fuel Injection ◽  
Injection Timing ◽  
Ignition Timing ◽  
Hcci Engine ◽  
Auto Ignition ◽  
Negative Valve Overlap ◽  
Valve Overlap ◽  
Direct Fuel Injection

Despite the fact that HCCI engines are distinguished by mixture homogeneity, some degree of stratification always appears inside a combustion chamber. It is especially applied to residual effect engines utilizing negative valve overlap. Mixture stratification is a result of the imperfect mixing of fresh air with trapped residuals. Direct fuel injection introduces stratification as well, due to fuel vaporization. As a consequence, the temperature within the combustion chamber is uneven. Thermal stratification affects auto-ignition timing and combustion evolution in a high extent. The purpose of this study was to evaluate a degree of thermal stratification in HCCI engine utilizing negative valve overlap. Investigations were performed using three-dimensional CFD model of the combustion system, made by using AVL FIRE software. Simulations were realized for various timings of fuel injection into the cylinder. It was found that fuel injection timing had a significant effect on the thermal stratification and resulting auto-ignition timing.

Modelling and Simulation of Homogeneous Charge Compression Ignition Engine Fueled by Biodiesel

2018 ◽  
Author(s):  
Meshack Hawi ◽  
Mahmoud Ahmed ◽  
Shinichi Ookawara
Keyword(s):  
Heat Release ◽  
Compression Ratio ◽  
Homogeneous Charge Compression Ignition ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Emission Characteristics ◽  
Compression Ignition ◽  
Hcci Engine ◽  
Hcci Engines ◽  
Homogeneous Charge

Homogeneous charge compression ignition (HCCI) is a combustion technology which has received increased attention of researchers in the combustion field for its potential in achieving low oxides of nitrogen (NOx) and soot emission in internal combustion (IC) engines. HCCI engines have advantages of higher thermal efficiency and reduced emissions in comparison to conventional internal combustion engines. In HCCI engines, ignition is controlled by the chemical kinetics, which leads to significant variation in ignition time with changes in the operating conditions. This variation limits the practical range of operation of the engine. Additionally, since HCCI engine operation combines the operating principles of both spark ignition (SI) and compression ignition (CI) engines, HCCI engine parameters such as compression ratio and injection timing may vary significantly depending on operating conditions, including the type of fuel used. As such, considerable research efforts have been focused on establishing optimal conditions for HCCI operation with both conventional and alternative fuels. In this study, numerical simulation is used to investigate the effect of compression ratio on combustion and emission characteristics of an HCCI engine fueled by pure biodiesel. Using a zero-dimensional (0-D) reactor model and a detailed reaction mechanism for biodiesel, the influence of compression ratio on the combustion and emission characteristics are studied in Chemkin-Pro. Simulation results are validated with available experimental data in terms of incylinder pressure and heat release rate to demonstrate the accuracy of the simulation model in predicting the performance of the actual engine. Analysis shows that an increase in compression ratio leads to advanced and higher peak incylinder pressure. The results also reveal that an increase in compression ratio produces advanced ignition and increased heat release rates for biodiesel combustion. Emission of NOx is observed to increase with increase in compression ratio while the effect of compression ratio on emissions of CO, CO2 and unburned hydrocarbon (UHC) is only marginal.

Sign in / Sign up

Export Citation Format

Share Document