Numerical Investigation on Mixture Formation of Two-Stroke LPG Direct Injection Engine Used as Range Extender for Electric Car

2016 ◽  
Author(s):  
B. Y. Xu ◽  
Y. L. Qi ◽  
C. D. Sun ◽  
J. Z. Ma
Keyword(s):  
High Speed ◽  
Direct Injection ◽  
Power Source ◽  
Calculation Model ◽  
Injection Timing ◽  
Mixture Formation ◽  
Range Extender ◽  
Electric Car ◽  
Spark Timing ◽  
Air Mixing

The two-stroke DI engine has distinct advantages such as high speed, high power density, and simple structure . LPG has a low boiling point and high saturation vapor pressure, which is very helpful in accelerating the fuel-air mixing. Owing to these characteristics and advantages, the two-stroke LPG engine is generally regarded as the preferred power source of the generator unit for extended-range electrical vehicles. The process of mixture formation is numerically simulated after the calculation model is validated by results from optical experiments. The results show that, under conditions of avoidance of fuel short-circuiting, an injection timing of 50° CA ABDC for engine start and warming (2000 rpm), and an 40° CA ABDC for running as the power source of the generator (4800 rpm) are appropriate. Further analysis of the velocity and concentration fields shows that the fresh mixture is locked in the cylinder when the exhaust port is closed (73° CA ABDC) and the homogeneous mixture can be formed at spark timing.

CFD Modelling of the Effects of Injection Timing on the Combustion Process and Emissions in an HSDI Diesel Engine

2012 ◽  
Author(s):  
Raouf Mobasheri ◽  
Zhijun Peng
Keyword(s):  
Diesel Engine ◽  
High Speed ◽  
Cfd Simulation ◽  
Direct Injection ◽  
Combustion Process ◽  
Injection Timing ◽  
Cfd Modelling ◽  
Combustion Modeling ◽  
Pressure Trace ◽  
Hsdi Diesel Engine

High-Speed Direct Injection (HSDI) diesel engines are increasingly used in automotive applications due to superior fuel economy. An advanced CFD simulation has been carried out to analyze the effect of injection timing on combustion process and emission characteristics in a four valves 2.0L Ford diesel engine. The calculation was performed from intake valve closing (IVC) to exhaust valve opening (EVO) at constant speed of 1600 rpm. Since the work was concentrated on the spray injection, mixture formation and combustion process, only a 60° sector mesh was employed for the calculations. For combustion modeling, an improved version of the Coherent Flame Model (ECFM-3Z) has been applied accompanied with advanced models for emission modeling. The results of simulation were compared against experimental data. Good agreement of calculated and measured in-cylinder pressure trace and pollutant formation trends were observed for all investigated operating points. In addition, the results showed that the current CFD model can be applied as a beneficial tool for analyzing the parameters of the diesel combustion under HSDI operating condition.

Effect of Swirl Ratio and Injection Pressure on Autoignition, Combustion and Emissions in a High Speed Direct Injection Diesel Engine Fuelled With Biodiesel (B-20)

2009 ◽  
Author(s):  
Vinay Nagaraju ◽  
Mufaddel Dahodwala ◽  
Kaushik Acharya ◽  
Walter Bryzik ◽  
Naeim A. Henein
Keyword(s):  
Diesel Engine ◽  
High Speed ◽  
Direct Injection ◽  
Injection Pressure ◽  
Combustible Mixture ◽  
Injection System ◽  
Ignition Process ◽  
Swirl Ratio ◽  
Mixture Formation ◽  
Physical And Chemical

Biodiesel has different physical and chemical properties than ultra low sulfur diesel fuel (ULSD). The low volatility of biodiesel is expected to affect the physical processes, mainly fuel evaporation and combustible mixture formation. The higher cetane number of biodiesel is expected to affect the rates of the chemical reactions. The combination of these two fuel properties has an impact on the auto ignition process, subsequently combustion and engine out emissions. Applying different swirl ratios and injection pressures affect both the physical and chemical processes. The focus of this paper is to investigate the effect of varying the swirl ratio and injection pressure in a single-cylinder research diesel engine using a blend of biodiesel and ULSD fuel. The engine is a High Speed Direct Injection (HSDI) equipped with a common rail injection system, EGR system and a swirl control mechanism. The engine is operated under simulated turbocharged conditions with 3 bar Indicated Mean Effective Pressure (IMEP) at 1500 rpm, using 100% ULSD and a blend of 20% biodiesel and 80% ULSD fuel. The biodiesel is developed from soy bean oil. A detailed analysis of the apparent rate of heat release (ARHR) is made to determine the role of the biodiesel component of B-20 in the combustible mixture formation, autoignition process, premixed, mixing controlled and diffusion controlled combustion fractions. The results explain the factors that cause an increase or a drop in NOx emissions reported in the literature when using biodiesel.

Numerical Investigation on Mixture Formation in a Turbocharged Port-Injection Natural Gas Engine Using Multiple Cycle Simulation

2018 ◽  
Vol 140 (5) ◽  
Author(s):  
Zhenkuo Wu ◽  
Zhiyu Han
Keyword(s):  
Fuel Injection ◽  
Load Condition ◽  
Operating Conditions ◽  
Injection Timing ◽  
Mixture Formation ◽  
Natural Gas Engine ◽  
Cycle Simulation ◽  
Mixture Preparation ◽  
Spark Timing ◽  
Multiple Cycle

In the present study, multidimensional computational fluid dynamics (CFD) simulations were carried out to study mixture formation in a turbocharged port-injection natural gas engine. In order to achieve robust simulation results, multiple cycle simulation was employed to remove the inaccuracies of initial conditions setting. First, the minimal number of simulation cycles required to obtain convergent cycle-to-cycle results was determined. Based on this, the in-cylinder mixture preparation for three typical operating conditions was studied. The effects of fuel injection timing and intake valve open scheme on the mixture formation were evaluated. The results demonstrated that three simulation cycles are needed to achieve convergence of the results for the present study. The analysis of the mixture preparation revealed that only in the initial phase of the intake stroke, there is an obvious difference between the three operating conditions. At the spark timing, for 5500 rpm, full load condition mixture composition throughout the cylinder is flammable, and for 2000 rpm, 2 bar operating condition part of the mixture is lean and nonflammable. The fuel injection timing has an insignificant impact on the mixture flammability at the spark timing. It was observed that the designed nonsynchronous intake valve open scheme has stronger swirl and x-direction tumble motion than the baseline case, leading to better mixture homogeneity and spatial distribution. With an increase in volumetric efficiency, particularly at 2000 rpm, full load condition, by 4.85% compared to the baseline, which is in line with experimental observation.

On the Premixed Combustion in a Direct-Injection Diesel Engine

1987 ◽  
Vol 109 (2) ◽  
pp. 187-192 ◽  
Author(s):  
A. C. Alkidas
Keyword(s):  
Diesel Engine ◽  
High Speed ◽  
Engine Speed ◽  
Direct Injection ◽  
Premixed Combustion ◽  
Injection Timing ◽  
Oxides Of Nitrogen ◽  
Nitrogen Emissions ◽  
Direct Injection Diesel Engine ◽  
Diffusion Burning

The factors influencing premixed burning and the importance of premixed burning on the exhaust emissions from a small high-speed direct-injection diesel engine were investigated. The characteristics of premixed and diffusion burning were examined using a single-zone heat-release analysis. The mass of fuel burned in premixed combustion was found to be linearly related to the product of engine speed and ignition-delay time and to be essentially independent of the total amount of fuel injected. Accordingly, the premixed-burned fraction increased with increasing engine speed, with decreasing fuel-air ratio and with retarding injection timing. The hydrocarbon emissions did not correlate well with the premixed-burned fraction. In contrast, the oxides of nitrogen emissions were found to increase with decreasing premixed-burned fraction, indicating that diffusion burning, and not premixed burning, is the primary source of oxides of nitrogen emissions.

scholarly journals Inter-plume aerodynamics for gasoline spray collapse

2017 ◽  
Vol 19 (10) ◽  
pp. 1048-1067 ◽  
Author(s):  
Panos Sphicas ◽  
Lyle M Pickett ◽  
Scott A Skeen ◽  
Jonathan H Frank
Keyword(s):  
Ambient Temperature ◽  
High Speed ◽  
Direct Injection ◽  
Engine Performance ◽  
Operating Conditions ◽  
Momentum Exchange ◽  
Flow Recirculation ◽  
Plume Region ◽  
Image Velocimetry ◽  
Air Mixing

The collapse or merging of individual plumes of direct-injection gasoline injectors is of fundamental importance to engine performance because of its impact on fuel–air mixing. However, the mechanisms of spray collapse are not fully understood and are difficult to predict. The purpose of this work is to study the aerodynamics in the inter-spray region, which can potentially lead to plume collapse. High-speed (100 kHz) particle image velocimetry is applied along a plane between plumes to observe the full temporal evolution of plume interaction and potential collapse, resolved for individual injection events. Supporting information along a line of sight is obtained using simultaneous diffused back illumination and Mie-scatter techniques. Experiments are performed under simulated engine conditions using a symmetric eight-hole injector in a high-temperature, high-pressure vessel at the “Spray G” operating conditions of the engine combustion network. Indicators of plume interaction and collapse include changes in counter-flow recirculation of ambient gas toward the injector along the axis of the injector or in the inter-plume region between plumes. The effect of ambient temperature and gas density on the inter-plume aerodynamics and the subsequent plume collapse are assessed. Increasing ambient temperature or density, with enhanced vaporization and momentum exchange, accelerates the plume interaction. Plume direction progressively shifts toward the injector axis with time, demonstrating that the plume interaction and collapse are inherently transient.

Low-sooting combustion in a small-bore high-speed direct-injection diesel engine using narrow-angle injectors

2008 ◽  
Vol 222 (10) ◽  
pp. 1927-1937 ◽  
Author(s):  
T-G Fang ◽  
R E Coverdill ◽  
C-F F Lee ◽  
R A White
Keyword(s):  
Diesel Engine ◽  
High Speed ◽  
Direct Injection ◽  
Fuel Efficiency ◽  
Operating Conditions ◽  
Injection Timing ◽  
Exhaust Pipe ◽  
Injection Angle ◽  
Direct Injection Diesel Engine ◽  
Combustion Flame

An optically accessible high-speed direct-injection diesel engine was used to study the effects of injection angles on low-sooting combustion. A digital high-speed camera was employed to capture the entire cycle combustion and spray evolution processes under seven operating conditions including post-top-dead centre (TDC) injection and pre-TDC injection strategies. The nitrogen oxide (NO x) emissions were also measured in the exhaust pipe. In-cylinder pressure data and heat release rate calculations were conducted. All the cases show premixed combustion features. For post-TDC injection cases, a large amount of fuel deposition is seen for a narrower-injection-angle tip, i.e. the 70° tip, and ignition is observed near the injector tip in the centre of the bowl, while for a wider-injection-angle tip, namely a 110° tip, ignition occurs near the spray tip in the vicinity of the bowl wall. The combustion flame is near the bowl wall and at the central region of the bowl for the 70° tip. However, the flame is more distributed and centralized for the 110° tip. Longer spray penetration is found for the pre-TDC injection timing cases. Liquid fuel impinges on the bowl wall or on the piston top and a fuel film is formed. Ignition for all the pre-TDC injection cases occur in a distributed way in the piston bowl. Two different combustion modes are observed for the pre-TDC injection cases including a homogeneous bulky combustion flame at earlier crank angles and a heterogeneous film combustion mode with luminous sooting flame at later crank angles. In terms of soot emissions, NO x emissions, and fuel efficiency, results show that the late post-TDC injection strategy gives the best performance.

Effect of Conical Spray and Multi-Hole Spray on Gasoline Engine Mixture Formation and Combustion Performance Based on Different Injection Strategies

2020 ◽  
Vol 143 (6) ◽  
Author(s):  
Shengli Wei ◽  
Zhiqing Yu ◽  
Zhilei Song ◽  
Fan Yang ◽  
Chengcheng Wu
Keyword(s):  
Gasoline Engine ◽  
Direct Injection ◽  
Mixture Distribution ◽  
Gasoline Direct Injection ◽  
Injection Timing ◽  
Mixture Formation ◽  
Injection Strategy ◽  
Gdi Engine ◽  
The Difference ◽  
Injection Strategies

Abstract This article presents a numerical investigation carried out to determine the effects of second and third injection timing on combustion characteristics and mixture formation of a gasoline direct injection (GDI) engine by comparing conical spray against multihole spray. The results showed that at the engine 80% full load of 2000 r/min, the difference in mixture distribution between the two sprays was obvious with double and triple injection strategies. With the second injection timing from 140 deg CA delay to 170 deg CA, the in-cylinder pressure, the in-cylinder temperature, and the heat release rate of the conical spray increased by 20.8%, 9.8%, and 30.7% and that of the multihole spray decreased by 30.7%, 13.6%, and 37.8%. The delay of the injection time reduced the performance of the engine with the multihole spray, and the performance of the multihole spray was obviously in the simulation of the triple injection strategy. However, for the conical spray, the application of the triple injection strategy increased the temperature and the pressure compared with the double injection strategy.

Sign in / Sign up

Export Citation Format

Share Document