Analysis of Unsteady Turbulent Merging Jet Flows With Temperature Difference

2002 ◽  
Author(s):  
Geun Jong Yoo ◽  
Won Dae Jeon
Keyword(s):  
Temperature Variation ◽  
Turbulent Flows ◽  
Turbulence Model ◽  
Flow Characteristics ◽  
Turbulence Models ◽  
Jet Flow ◽  
Reynolds Stress Model ◽  
Jet Flows ◽  
Test Cases ◽  
Temperature Variance

Suitable turbulence model is required in the course of establishing a proper analysis methodology for thermal stripping phenomena. For this purpose, three different turbulence models of k-ε model, modified k-ε model, and full Reynolds stress model and VLES are applied to analyze unsteady turbulent flows with temperature variation. Four test cases are selected for verification. These are vertical jet flows with water and sodium, parallel jet flow with sodium, and merging pipe flow through T-junction with sodium. The geometries of test cases well represent common places where thermal stripping might be occurred. The turbulence model computation shows overall jet flow characteristics well and good comparison of mean temperature distribution. Temperature variance (θ′2) is rather over-predicted, but location of high temperature variance is matched well with that of the large amplitude of temperature variation of experimental results. Meanwhile, mixing of hot and cold jet flow is found to be not that active.

Analysis of Impinging and Countercurrent Stagnating Flows by Reynolds Stress Model

2002 ◽  
Vol 124 (3) ◽  
pp. 706-718 ◽  
Author(s):  
Yong H. Im ◽  
Kang Y. Huh ◽  
Kwang-Yong Kim
Keyword(s):  
Numerical Simulation ◽  
Kinetic Energy ◽  
Turbulent Flows ◽  
Reynolds Stress ◽  
Dissipation Rate ◽  
Flow Characteristics ◽  
Turbulence Models ◽  
Reynolds Stress Model ◽  
Stress Model ◽  
Stagnation Region

Numerical simulation is performed for stagnating turbulent flows of impinging and countercurrent jets by the Reynolds stress model (RSM). Results are compared with those of the k−ε model and available data to assess the flow characteristics and turbulence models. Three variants of the RSM tested are those of Gibson and Launder (GL), Craft and Launder (GL-CL) and Speziale, Sarkar and Gatski (SSG). As is well known, the k−ε model significantly overestimates turbulent kinetic energy near the wall. Although the RSM is superior to the k−ε model, it shows considerable difference according to how the redistributive pressure-strain term is modeled. Results of the RSM for countercurrent jets are improved with the modified coefficients for the dissipation rate, Cε1 and Cε2, suggested by Champion and Libby. Anisotropic states of the stress near the stagnation region are assessed in terms of an anisotropy invariant map (AIM).

scholarly journals Analysis of Flow Characteristics and Effects of Turbulence Models for the Butterfly Valve

2021 ◽  
Vol 11 (14) ◽  
pp. 6319
Author(s):  
Sung-Woong Choi ◽  
Hyoung-Seock Seo ◽  
Han-Sang Kim
Keyword(s):  
Turbulence Model ◽  
Dissipation Rate ◽  
Flow Characteristics ◽  
Turbulence Models ◽  
Flow Properties ◽  
Nominal Diameter ◽  
Large Pressure ◽  
Sst Model ◽  
Turbulence Effect ◽  
Valve Opening

In the present study, the flow characteristics of butterfly valves with different sizes DN 80 (nominal diameter: 76.2 mm), DN 262 (nominal diameter: 254 mm), DN 400 (nominal diameter: 406 mm) were numerically investigated under different valve opening percentages. Representative two-equation turbulence models of two-equation k-epsilon model of Launder and Sharma, two-equation k-omega model of Wilcox, and two-equation k-omega SST model of Menter were selected. Flow characteristics of butterfly valves were examined to determine turbulence model effects. It was determined that increasing turbulence effect could cause many discrepancies between turbulence models, especially in areas with large pressure drop and velocity increase. In addition, sensitivity analysis of flow properties was conducted to determine the effect of constants used in each turbulence model. It was observed that the most sensitive flow properties were turbulence dissipation rate (Epsilon) for the k-epsilon turbulence model and turbulence specific dissipation rate (Omega) for the k-omega turbulence model.

Temperature Corrected Turbulence Model for High Temperature Jet Flow

2004 ◽  
Vol 126 (5) ◽  
pp. 844-850 ◽  
Author(s):  
Khaled S. Abdol-Hamid ◽  
S. Paul Pao ◽  
Steven J. Massey ◽  
Alaa Elmiligui
Keyword(s):  
High Temperature ◽  
Turbulence Model ◽  
Room Temperature ◽  
Eddy Viscosity ◽  
Mixing Layer ◽  
Supersonic Jet ◽  
Turbulence Models ◽  
Jet Flows ◽  
Viscosity Term ◽  
Mixing Layer Flows

It is well known that the two-equation turbulence models under-predict mixing in the shear layer for high temperature jet flows. These turbulence models were developed and calibrated for room temperature, low Mach number, and plane mixing layer flows. In the present study, four existing modifications to the two-equation turbulence model are implemented in PAB3D and their effect is assessed for high temperature jet flows. In addition, a new temperature gradient correction to the eddy viscosity term is tested and calibrated. The new model was found to be in the best agreement with experimental data for subsonic and supersonic jet flows at both low and high temperatures.

Improved Prediction of Turbomachinery Flows Using Near-Wall Reynolds-Stress Model

2001 ◽  
Vol 124 (1) ◽  
pp. 86-99 ◽  
Author(s):  
G. A. Gerolymos ◽  
J. Neubauer ◽  
V. C. Sharma ◽  
I. Vallet
Keyword(s):  
Experimental Data ◽  
Turbulent Flows ◽  
Reynolds Stress ◽  
Turbulence Models ◽  
Reynolds Stress Model ◽  
Stress Model ◽  
Reynolds Stresses ◽  
Mean Flow ◽  
Flow Equations ◽  
Near Wall

In this paper an assessment of the improvement in the prediction of complex turbomachinery flows using a new near-wall Reynolds-stress model is attempted. The turbulence closure used is a near-wall low-turbulence-Reynolds-number Reynolds-stress model, that is independent of the distance-from-the-wall and of the normal-to-the-wall direction. The model takes into account the Coriolis redistribution effect on the Reynolds-stresses. The five mean flow equations and the seven turbulence model equations are solved using an implicit coupled OΔx3 upwind-biased solver. Results are compared with experimental data for three turbomachinery configurations: the NTUA high subsonic annular cascade, the NASA_37 rotor, and the RWTH 1 1/2 stage turbine. A detailed analysis of the flowfield is given. It is seen that the new model that takes into account the Reynolds-stress anisotropy substantially improves the agreement with experimental data, particularily for flows with large separation, while being only 30 percent more expensive than the k−ε model (thanks to an efficient implicit implementation). It is believed that further work on advanced turbulence models will substantially enhance the predictive capability of complex turbulent flows in turbomachinery.

Sensitization of the SST Turbulence Model to Rotation and Curvature by Applying the Spalart–Shur Correction Term

2009 ◽  
Vol 131 (4) ◽  
Author(s):  
Pavel E. Smirnov ◽  
Florian R. Menter
Keyword(s):  
Turbulent Flows ◽  
Turbulence Model ◽  
Transport Model ◽  
Correction Term ◽  
Computational Cost ◽  
Turbulence Models ◽  
Reynolds Stress Transport Model ◽  
Wide Range ◽  
Sst Model ◽  
The One

A rotation-curvature correction suggested earlier by Spalart and Shur (1997, “On the Sensitization of Turbulence Models to Rotation and Curvature,” Aerosp. Sci. Technol., 1(5), pp. 297–302) for the one-equation Spalart–Allmaras turbulence model is adapted to the shear stress transport model. This new version of the model (SST-CC) has been extensively tested on a wide range of both wall-bounded and free shear turbulent flows with system rotation and/or streamline curvature. Predictions of the SST-CC model are compared with available experimental and direct numerical simulations (DNS) data, on the one hand, and with the corresponding results of the original SST model and advanced Reynolds stress transport model (RSM), on the other hand. It is found that in terms of accuracy the proposed model significantly improves the original SST model and is quite competitive with the RSM, whereas its computational cost is significantly less than that of the RSM.

Numerical Assessment of Different Turbulence Models for Slot Jet Impinging on Flat and Concave Surfaces

2002 ◽  
Author(s):  
Rongguang Jia ◽  
Masoud Rokni ◽  
Bengt Sunde´n
Keyword(s):  
Turbulent Flows ◽  
Numerical Study ◽  
Turbulence Models ◽  
Detailed Comparison ◽  
Reynolds Numbers ◽  
Reynolds Stress Model ◽  
Eddy Viscosity Model ◽  
Flow And Heat Transfer ◽  
Numerical Assessment ◽  
Transfer Problems

A numerical study has been carried out for slot jet impinging on flat and concave surfaces. Five turbulence models are employed for the predictions of these strongly strained turbulent flows, namely linear eddy viscosity model (LEVM), low-Re explicit algebraic Reynolds stress model (EASM) and three different V2F models. A bounded formulation for Cμ was also introduced to account for the better prediction of the wall jet development. The studied Reynolds numbers vary from 8,000 to 20,000, and nozzle-to-surface distance (H) is in the range of 1≤H/B≤8. Detailed comparison is made between the results from the models and available experimental data to test the ability of the models in predicting these fluid flow and heat transfer problems.

Development and Application of a Two-Scale Non-Linear Reynolds Stress Turbulence Model

2007 ◽  
Author(s):  
S. Y. Jaw ◽  
R. R. Hwang
Keyword(s):  
Turbulent Flows ◽  
Reynolds Stress ◽  
Turbulence Model ◽  
Dissipation Rate ◽  
Reynolds Stress Model ◽  
Stress Model ◽  
Turbulence Scale ◽  
Non Linear ◽  
Algebraic Reynolds Stress Model ◽  
Near Wall

To improve the prediction of turbulent flows, a two-scale, non-linear Reynolds stress turbulence model is proposed in this study. It is known that for the near-wall low-Reynolds number turbulent flows, the Kolmogorov turbulence scale, based on the fluid kinematic viscosity and dissipation rate of turbulent kinetic energy (ν,ε), is the dominant turbulence scale, hence it is adopted to address the viscous effects and the rapid increase of dissipation rate in the near wall region. As a wall is approached, the turbulence scale transits smoothly from turbulent kinetic energy based (k, ε) scale to (ν,ε) scale. The damping functions of the low-Reynolds number models can thus be simplified and the near-wall turbulence characteristics, such as the ε distribution, are correctly reproduced. Furthermore, to improve the prediction of the anisotropic Reynolds stresses for complex flows, a nonlinear algebraic Reynolds stress model is incorporated. The same turbulence scales are adopted in the nonlinear algebraic Reynolds stress model. The developed two-scale non-linear Reynolds stress model is first calibrated with the DNS budgets of two-dimensional channel flows, and then applied to predict the separation flow behind a backward facing step. It is found that the proposed two-scale nonlinear Reynolds stress turbulence model is capable of providing satisfactory results without increasing much computation efforts or causing numerical stability problems.

On Turbulent Flows Dominated by Curvature Effects

1992 ◽  
Vol 114 (1) ◽  
pp. 52-57 ◽  
Author(s):  
G. C. Cheng ◽  
S. Farokhi
Keyword(s):  
Turbulent Flows ◽  
Turbulence Model ◽  
Dominant Role ◽  
Longitudinal Velocity ◽  
Turbulence Models ◽  
Separated Flows ◽  
Local Curvature ◽  
Streamline Curvature ◽  
Curvature Effects ◽  
Numerical Predictions

A technique for improving the numerical predictions of turbulent flows with the effect of streamline curvature is developed. Separated flows and the flow in a curved duct are examples of flow fields where streamline curvature plays a dominant role. New algebraic formulations for the eddy viscosity μt incorporating the k–ε turbulence model are proposed to account for various effects of streamline curvature. The loci of flow reversal (where axial velocities change signs) of the separated flows over various backward-facing steps are employed to test the capability of the proposed turbulence model in capturing the effect of local curvature. The inclusion of the effect of longitudinal curvature in the proposed turbulence model is validated by predicting the distributions of the longitudinal velocity and the static pressure in an S-bend duct and in 180 deg turn-around ducts. The numerical predictions of different curvature effects by the proposed turbulence models are also reported.

Simulation of Turbulent Flows in Turbine Blade Passages and Disc Cavities

2008 ◽  
Author(s):  
Konstantin N. Volkov ◽  
Nicholas J. Hills ◽  
John W. Chew
Keyword(s):  
Flat Plate ◽  
Turbulent Flows ◽  
Turbine Blade ◽  
Plate Boundary ◽  
Turbulence Models ◽  
Benchmark Problems ◽  
Test Cases ◽  
Cavity Model ◽  
Rotating Disc ◽  
Wall Functions

The main objectives of the paper are to test widely used turbulence models against selected benchmark problems identifying range of applicability and limitations of the models used and to help accurately predict flow in turbine blade passages and disc cavities. The following models are considered: the k–ε model with and without a Kato–Launder correction and a Richardson number correction, the two-layer k–ε/k–l model, and the Spalart–Allmaras model with and without correction for rotation. Weaknesses in the models are identified and suggestions made for possible improvements. Numerical implementation of the wall functions approach is also considered. The test cases considered include flat plate boundary layer, flat plate heat transfer, enclosed rotating disc, and a combined turbine blade/disc cavity model. Comparisons are made with experimental data and computations from different CFD codes.

Numerical study of the flow field characteristics over a backward facing step using k-kl-ω turbulence model: comparison with different models

2018 ◽  
Vol 15 (1) ◽  
pp. 173-180 ◽  
Author(s):  
Yasser M. Ahmed ◽  
A.H. Elbatran
Keyword(s):  
Experimental Data ◽  
Fluid Mechanics ◽  
Turbulence Model ◽  
Flow Separation ◽  
Flow Characteristics ◽  
Turbulence Models ◽  
Numerical Results ◽  
Backward Facing Step ◽  
Content Type ◽  
Case Comparison

Purpose This paper aims to investigate numerically the turbulent flow characteristics over a backward facing step. Different turbulence models with hybrid computational grid have been used to study the detached flow structure in this case. Comparison between the numerical results and the available experiment data is carried out in the present study. The results of the different turbulence models were in a good agreement with the experimental results. The numerical results also concluded that the k-kl-ω turbulence model gave favorable results compared with the experiment. Design/methodology/approach It is very important to study the flow characteristics of detached flows. Therefore, the current study investigates numerically the flow characteristics in backward facing step by using two-, three- and seven-equation turbulence models in the finite volume code ANSYS Fluent. In addition, hybrid grid has been used to improve the capability of the unstructured mesh elements for predicting the flow separation in this case. Comparison between the different turbulence models and the available experimental data was done to find the most suitable turbulence model for simulating such cases of detached flows. Findings The present numerical simulations with the different turbulence models predicted efficiently the flow characteristics over the backward facing step. The transition k-kl-ω gave the best acceptable results compared with experimental data. This is a good concluded remark in the fields of fluid mechanics and hydrodynamics because the phenomenon of flow separation is not easy to be predicted numerically and can affect greatly on the predicted drag of moving bodies in many engineering applications. Originality/value The CFD results of using different turbulence models have been validated with the experimental work, and the results of k-kl-ω proven acceptable with flow characteristics. The results of the current study conclude that the use of k-kl-ω turbulence model will contribute towards a more efficient utilization in the fields of fluid mechanics and hydrodynamics.

Sign in / Sign up

Export Citation Format

Share Document