Mechanical Properties of Alumina Composite Hardened by Ultra Dispersed Diamonds

2002 ◽  
Author(s):  
Maksim Kireitseu ◽  
L. Yerakhavets ◽  
Ion Nemerenco
Keyword(s):  
Mechanical Properties ◽  
Spectral Analysis ◽  
Composite Coatings ◽  
Xrd Analysis ◽  
Hertzian Contact ◽  
Load Rating ◽  
X Ray ◽  
Variable Porosity ◽  
Alumina Composite

Structure and mechanical properties of composite coatings that contain of 5 to 25% (vol.) of ultra-dispersed diamonds, different alumina phases, and components of SiC, AlN have been investigated. Structure, grains morphology, presence of pores and their distribution, interaction zones were investigated with SEM, X-ray-phase analysis and micro-X-ray-spectral analysis. Material was formed by impulse pressing. It is revealed that the material has variable-porosity, high density, microhardness up to 25 GPa and load rating. XRD analysis shows that the structure includes the diamond phase. To investigate load rating of the material Hertzian contact was used. Ultra-dispersed diamonds strength the structure in general as well as mechanical properties and quality of composite coatings.

Development of Ternary Concrete Utilizing Agricultural Waste Material

2022 ◽  
Author(s):  
Sunita Kumari ◽  
Dhirendra Singhal ◽  
Rinku Walia ◽  
Ajay Rathee
Keyword(s):  
Rice Husk ◽  
Rice Husk Ash ◽  
Agricultural Waste ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Concrete Mix ◽  
Maize Cob

Abstract The present project proposes to utilize rice husk and maize cob husk ash in the cement to mitigate the adverse impact of cement on environment and to enhance the disposal of waste in a sustainable manner. Ternary concrete / MR concrete was prepared by using rise husk and maize cob ash with cement. For the present project, five concrete mixes MR-0 (Control mix), MR-1 (Rice husk ash 10% and MR-2.5%), MR-2 (Rice husk ash 10% and MR-5%), MR-3 (Rice husk ash 10% and MR-2.5%), MR-4 (Rice husk ash 10% and MR-2.5%) were prepared. M35 concrete mix was designed as per IS 10262:2009 for low slump values 0-25mm. The purpose is to find the optimum replacement level of cement in M35 grade ternary concrete for I – Shaped paver blocks.In order to study the effects of these additions, micro-structural and structural properties test of concretes have been conducted. The crystalline properties of control mix and modified concrete are analyzed by Fourier Transform Infrared Spectroscope (FTIR), Scanning Electron Microscopy (SEM), and X-Ray Diffraction (XRD). The results indicated that 10% Rice husk ash and 5% maize cob ash replaced with cement produce a desirable quality of ternary concrete mix having good compressive strength. The results of SEM analysis indicated that the morphology of both concrete were different, showing porous structure at 7 days age and become unsymmetrical with the addition of ashes. After 28 day age, the control mix contained more quantity of ettringite and became denser than ternary concrete. XRD analysis revealed the presence of portlandite in large quantity in controlled mix concrete while MR concrete had the partially hydrated particle of alite.

scholarly journals Effects of Bi2O3 Doping on the Mechanical Properties of PbO Ceramic Pellets Used in Lead-Cooled Fast Reactors

Materials ◽  
2019 ◽  
Vol 12 (12) ◽  
pp. 1948 ◽  
Author(s):  
Yan Ma ◽  
Anxia Yang ◽  
Huiping Zhu ◽  
Arslan Muhammad ◽  
Pengwei Yang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Eutectic Alloy ◽  
Composite Ceramic ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
Oxygen Control ◽  
Fast Reactors ◽  
Future Studies ◽  
X Ray ◽  
Lead Bismuth Eutectic

In this paper, the effects of Bi2O3 doping on the mechanical properties of PbO ceramic pellets were studied. Different ratios of Bi2O3/PbO (i.e., xBi2O3-(1−x) PbO, where x is 0, 1, 3, 5, or 7 wt.%) were fabricated and sintered at 570, 620, and 670 °C. Mechanical properties including density, hardness, flexural strength, and sintering of PbO were studied for each of the aforementioned compositions. Phase composition, microstructure, and the worn surfaces of the composites were characterized by scanning electron microscopy and X-ray diffraction (XRD). The XRD analysis revealed that a solid solution formed in the composite ceramic. The best suited conditions of temperature and doping of Bi2O3 for optimal sintering were found to be 620 °C and 3 wt.%, respectively. The hardness of the 3 wt.% Bi2O3-97 wt.% PbO ceramic was found to be 717 MPa, which is about four times higher than the hardness of pure PbO. In addition, the strength of the composites was found to be 43 MPa, which is two times higher than that of pure PbO. The integrity of the composites was verified using the lead–bismuth eutectic alloy flushing experiment. The results of this research paper are important for future studies of oxygen control in the lead–bismuth eutectic alloy of lead-cooled fast reactors.

MECHANICAL PROPERTIES OF A POLYURETHANE/MONTMORILLONITE NANOCOMPOSITE FEATURING ORGANOMODIFICATION SYNTHESIZED VIA IN SITU POLYMERIZATION

2015 ◽  
Vol 88 (1) ◽  
pp. 138-146 ◽  
Author(s):  
Rouhollah Bagheri ◽  
Reza Darvishi
Keyword(s):  
Mechanical Properties ◽  
In Situ Polymerization ◽  
Xrd Analysis ◽  
Silicate Layer ◽  
X Ray Diffraction ◽  
X Ray ◽  
End Groups ◽  
Layer Sample ◽  
Silicate Layers

ABSTRACT In this study, polyurethane (PU)/organomodified montmorillonite (cloisite®30B) is synthesized via in situ polymerization by reaction of an ether-based prepolymer with the isocyanate end groups and adiamine chain extender (4, 4-methylene-bis(2-chloroaniline)) in the presence of different amounts of nanoparticles dispersed in the prepolymer matrix by an ultrasonic mixer for 1 h. The synthesized polymers are cast on a pretreated carbon steel sheet and cured at 120 °C in an oven. The PU and its composites have been characterized by using Fourier transform infrared spectroscopy, X-ray diffraction (XRD), and mechanical testing. The XRD analysis of the cured samples containing 1 to 3 wt% cloisite30B showed intercalation segments in the silicate layers and exfoliation for 0.5 wt% nanoparticles. The highest mechanical properties were obtained using the cured exfoliated silicate layer sample. A twofold increase in the ultimate tensile strength and a 2.3 times increase in the adhesion strength were found for 0.5 wt% organoclay/PU as compared with that of pure PU. In addition, the exfoliated structure sample exhibited a 16% reduction in abrasion compared with that of pure PU.

EFFECT OF TiO2 PARTICLES ON MICRO-HARDNESS, CORROSION, WEAR AND FRICTION OF Ni–P–TiO2 COMPOSITE COATINGS AT DIFFERENT ANNEALING TEMPERATURES

2016 ◽  
Vol 23 (01) ◽  
pp. 1550082 ◽  
Author(s):  
PRASANNA GADHARI ◽  
PRASANTA SAHOO
Keyword(s):  
Wear Resistance ◽  
Corrosion Resistance ◽  
Composite Coatings ◽  
Corrosion Current ◽  
Xrd Analysis ◽  
Charge Transfer Resistance ◽  
Micro Hardness ◽  
Transfer Resistance ◽  
X Ray ◽  
Annealing Temperatures

The present study investigates the effect of titania particles on the micro-hardness, wear resistance, corrosion resistance and friction of electroless Ni–P–TiO2 composite coatings deposited on mild steel substrates at different annealing temperatures. The experimental results confirmed that the amount of TiO2 particles incorporated in the coatings increases with increase in the concentration of particles in the electroless bath. In presence of TiO2 particles, hardness, wear resistance and corrosion resistance of the coating improve significantly. At higher annealing temperature, wear resistance increases due to formation of hard Ni3P phase and incorporation of titania particles in the coated layer. Charge transfer resistance and corrosion current density of the coatings reduce with an increase in TiO2 particles, whereas corrosion potential increases. Microstructure changes and composition of the composite coating due to heat treatment are studied with the help of scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDXA) and X-ray diffraction (XRD) analysis.

Growth and Characterization of PZT Thin Films

2008 ◽  
Author(s):  
Daqun Bao ◽  
Yi Zhang ◽  
Hang Guo
Keyword(s):  
Thin Films ◽  
Sol Gel ◽  
Xrd Analysis ◽  
Annealing Process ◽  
Pzt Thin Films ◽  
X Ray ◽  
Crystallographic Structures ◽  
Strain Equation

This paper presents the growth and characterization of PZT thin films by using the sol-gel technology. In this paper, we study the influences of annealing process and different substrates on the orientation and crystalline quality of PZT thin films. The crystallographic structures are tested by using X-ray diffractometer (XRD), and the residual stresses of PZT thin films are obtained by calculation from a derived stress-strain equation in XRD analysis. Moreover, surface morphology and microstructure of the films are investigated by using AFM and SEM, and the polarization hysteresis of PZT thin films is measured by using a Sawyer Tower circuit. The results show that PZT thin films prepared by using the sol-gel method have good properties and can be used for developing PZT-based micro and nano devices.

Measurement of Alloying Degree of Galvannealed Steels by X-Ray Diffraction

2006 ◽  
Vol 321-323 ◽  
pp. 1461-1464 ◽  
Author(s):  
Hyoung Kuk Park ◽  
Jea Hwa Hong ◽  
Chong Soo Lee
Keyword(s):  
Mechanical Properties ◽  
Corrosion Resistance ◽  
Quantitative Analysis ◽  
Xrd Analysis ◽  
Pls Regression ◽  
Processing Conditions ◽  
X Ray Diffraction ◽  
X Ray ◽  
Excellent Corrosion Resistance ◽  
Galvannealed Steel

Galvannealed steels are produced by reheating of Zinc-coated steels, in which the iron and the zinc are interdiffused to form Zn-Fe intermatallic compound. In recent years, application of galvannealed steel has increased due to its excellent corrosion resistance, good weldability and paintability. Galvannealed production requires strict control of processing conditions to obtain an optimal alloying degree in the coatings. The analysis of the alloying degree is very important since they are closely related to the corrosion and mechanical properties. This study is measurement of alloying degree of the galvannealed steel by using the XRD. Partial least squares (PLS) model is a powerful multivariate tool that has been successfully applied to the quantitative analysis of data in XRD. The alloying degree was determined by using PLS regression to a concentration accuracy of 0.2%. The XRD analysis and proposed PLS model can be successfully used to determine the alloying degree of industrially produced galvannealed steel.

Effect of expandable and expanded graphites on the thermo-mechanical properties of polyamide 11

2018 ◽  
Vol 51 (2) ◽  
pp. 175-190 ◽  
Author(s):  
F Oulmou ◽  
A Benhamida ◽  
A Dorigato ◽  
A Sola ◽  
M Messori ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Xrd Analysis ◽  
Crystal Form ◽  
X Ray Diffraction ◽  
Polyamide 11 ◽  
X Ray ◽  
Diffraction Peaks ◽  
Graphite Composites ◽  
And Storage

The preparation and thermo-mechanical characterization of composites based on polyamide 11 (PA11) filled with various amounts of both expandable and expanded graphites are presented. Investigation conducted using X-ray diffraction (XRD), scanning electron microscopy and surface area analyses indicated how graphite expanded under the selected processing conditions. The XRD analysis on PA11/graphite composites revealed no change in the crystal form of the PA11, while the presence of diffraction peaks associated to the graphite-stacked lamellae can be still detected. All the investigated composites showed an improvement of the thermal stability and mechanical properties (elastic and storage moduli).

Application of Mixed Ceramic Powder in Cement Based Composites

2014 ◽  
Vol 1054 ◽  
pp. 177-181 ◽  
Author(s):  
Jaroslav Pokorný ◽  
Jan Fořt ◽  
Milena Pavlíková ◽  
Jiří Studnička ◽  
Zbyšek Pavlík
Keyword(s):  
Mechanical Properties ◽  
Ceramic Powder ◽  
Xrd Analysis ◽  
Point Of View ◽  
Future Research ◽  
Cement Pastes ◽  
X Ray ◽  
Performance Point ◽  
Particles Size Distribution ◽  
Mixed Ceramic

Waste ceramic powder coming from grinding the ceramic bricks disposed on demolition depot is investigated as partial Portland cement replacement in blended binders. For the milled ceramic powder, measurement of specific surface area (SSA) and particles size distribution is done. Its chemical composition is accessed using X-Ray Fluorescence (XRF) and X-Ray Diffraction (XRD) analysis. The blended binders containing ceramic powder in an amount of 8, 16, 24, 32, and 40% of mass of cement are used for the preparation of cement pastes which are then characterized using the measurement of basic physical properties, mechanical properties, hygric and thermal properties. The obtained results show that an application of 8 and 16% ceramic powder in the blended binder provides sufficient mechanical properties of the pastes with relatively low hygric transport properties. From the thermal performance point of view, the incorporation of ceramic powder decreases the heat transport in all the tested pastes. This makes good prerequisites for future research that will be focused on the development of new types of cement-based composites with incorporated ceramic waste powder.

Mechanical Properties of Fly Ash-Slag-Dredged Silt System Stimulated by Alkali

2013 ◽  
Vol 807-809 ◽  
pp. 1140-1146 ◽  
Author(s):  
Yi Xuan Chen ◽  
Xiu Li Sun ◽  
Zhi Hua Li
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Fly Ash ◽  
Construction Materials ◽  
Xrd Analysis ◽  
Test Results ◽  
X Ray Diffraction ◽  
Shear Tests ◽  
X Ray ◽  
Direct Shear Tests

The objective of this work is to investigate the stimulation effect of the addition of alkali on the fly ash and slag for stabilizing dredged silt. Based on the test results, a viable alternative for the final disposal of dredged silt as subgrade construction materials were proposed. For this purpose, several mixtures of dredged silt-fly ash-slag and alkali were prepared and stabilized/solidified. In this system, fly ash and slag were used as hardening agents (solidified materials) of dredged silt and alkali was used as activator of fly ash and slag. The shear strength of the mixture was tested by several direct shear tests. Furthermore, X-Ray Diffraction (XRD) analysis was used to determine the hydration products of the system. The specimens were tested in order to determine the shear strength changes versus hydration time and the alkali content. It is indicated that mechanical properties of solidified silt are improved significantly by addition of fly ash and slag stimulated by alkali.

Characterization of Ti-xNb (x = 25 – 35) Alloys in as Melt and Annealed States

2019 ◽  
Vol 946 ◽  
pp. 287-292
Author(s):  
Alexander Thoemmes ◽  
Ivan V. Ivanov ◽  
Alexey Ruktuev
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Β Phase ◽  
Α Phase ◽  
Nb Content ◽  
Scanning Electron

The effect of Nb content on microstructure, mechanical properties and phase formation in as-melt and annealed binary Ti-Nb alloys were investigated using scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX) and X-ray diffraction (XRD) analysis. The content of Nb varied in the range 25-35 mass % leading to significant changes in the microstructure. The annealed and furnace-cooled binary Ti-Nb samples exhibited HCP martensitic α` phase at a Nb content below 27.5 mass % and metastable BCC β phase at higher contents of Nb. The mechanical properties of alloys depended strongly on the Nb content and type of the dominating phase.

Sign in / Sign up

Export Citation Format

Share Document