Impact Failure Analysis of Glass/Epoxy Textile Composites

2000 ◽  
Author(s):  
Sabit Adanur ◽  
Levent Onal
Keyword(s):  
Failure Analysis ◽  
Volume Fraction ◽  
Textile Composites ◽  
Molding Pressure ◽  
Curing Agent ◽  
Mixing Ratio ◽  
Production Parameters ◽  
Number Of Layers ◽  
The Impact ◽  
Composite Properties

Abstract The production parameters of composites are effective on the impact properties of the material. The effects of the number of layers, thickness, manufacturing characteristics such as molding time, molding temperature, molding pressure and the mixing ratio of epoxy resin and curing agent were examined at the same volume fraction ratio. There is an optimum point for most of the variables. Parameters below and above of this point lead an increase in deflection level. Impact velocity is effective on the composite properties as well.

Effects of Production Variables on Stress-Strain Behavior of Glass/Epoxy Textile Composites in Compression Molding

2000 ◽  
Author(s):  
Sabit Adanur ◽  
Levent Onal
Keyword(s):  
Volume Fraction ◽  
Textile Composites ◽  
Molding Pressure ◽  
Stress And Strain ◽  
Curing Agent ◽  
Reinforced Composites ◽  
Mixing Ratio ◽  
Strain Behavior ◽  
Production Parameters ◽  
Glass Reinforced Composites

Abstract The production parameters of glass-reinforced composites have a significant effect on the tensile properties of the material. The effects of manufacturing characteristics such as molding time, molding temperature, molding pressure and mixing ratio of epoxy resin and curing agent on stress and strain values of the composites were examined at the same volume fraction ratio.

Impact Behaviors of Flax/Polypropylene Weft Knitted Composites

2010 ◽  
Vol 146-147 ◽  
pp. 400-407 ◽  
Author(s):  
Hong Xia Li ◽  
Li Liu ◽  
Jian Ming Zhang ◽  
Ya Nan Liu ◽  
Gu Huang
Keyword(s):  
Impact Test ◽  
Volume Fraction ◽  
Textile Composites ◽  
Flax Fiber ◽  
The Impact

For developing the environmentally protective civil textile composites with better impact behaviors, the impact test was made with flax/polypropylene weft knitting composites samples. The mechanisms of fiber reinforcing and fracture were discussed through examining the fracture photographs. This research shows that the samples have better impact behaviors when the volume fraction of flax fiber is about 50%，the amount of layers is 8, and the sinker depth of the flax/pp knitted perform is 9.

scholarly journals Analysis of Number of Layers and Volume Fraction of Fiber Against Shock Load and Composite Compressive Strength Wind Turbine Propeller

2021 ◽  
Vol 21 (3) ◽  
pp. 165-171
Author(s):  
Kris Witono ◽  
◽  
Pondi Udianto ◽  
Heru Prasetyo ◽  
Sugeng Hadi Susilo ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Impact Test ◽  
Bending Strength ◽  
Volume Fraction ◽  
Fiber Composite ◽  
Shock Load ◽  
Material Structure ◽  
Number Of Layers ◽  
The Impact ◽  
Very High

The manufacture of wind turbine blades has a very high risk of failure, especially in the manufacturing section or in this case the material structure. If the structure of the propeller material is not able to withstand the very high pressure and air flow, it will result in the failure of the material structure when it is in use. For this reason, the purpose of this study was to determine the composition of composite materials that have high strength and toughness properties and are suitable for wind turbine propellers. The method used in this research is experimental. The independent variables include the number of layers and the volume fraction of straw fiber. The dependent variables are shock load and compressive strength. Each compression test specimen is made with a gauge length of 100mm, a width of 25mm, and a thickness of 2.5mm. While the impact test specimens are made equal to l25mm long, l2mm wide, l2mm high, and 2mm notch. The results showed that the bending strength of the straw fiber composite with 6 layers had an increasing trend as the number of layers increased. The highest bending strength with the number of piles of 6 layers and the lowest strength with the number of piles of 2 layers. In addition, the volume fraction is very influential on the bending stress of the straw composite matrix. It can be seen that the matrix with a volume fraction of 50% has the greatest bending stress in each number of layers, both 2, 4 and 6. For the impact test, it is found that the optimal number of layers occurs in the number of 2 layers with a volume fraction of 33%. The shock load tends to decrease. Meanwhile, based on the volume fraction, the larger the volume fraction, the smaller the shock load that can be received by the straw fiber composite material.

VLSI Design for Functional Failure Analysis in the < 90 nm and Flip-Chip Era

2003 ◽  
Author(s):  
Yoav Weizman ◽  
Ezra Baruch
Keyword(s):  
Failure Analysis ◽  
Flip Chip ◽  
Light Emission ◽  
Vlsi Design ◽  
Optical Resolution ◽  
Critical Issue ◽  
Acquisition Time ◽  
Resolution Limit ◽  
Design Rules ◽  
The Impact

Abstract In recent years, two new techniques were introduced for flip chip debug; the Laser Voltage Probing (LVP) technique and Time Resolved Light Emission Microscopy (TRLEM). Both techniques utilize the silicon’s relative transparency to wavelengths longer than the band gap. This inherent wavelength limitation, together with the shrinking dimensions of modern CMOS devices, limit the capabilities of these tools. It is known that the optical resolution limits of the LVP and TRLEM techniques are bounded by the diffraction limit which is ~1um for both tools using standard optics. This limitation was reduced with the addition of immersion lens optics. Nevertheless, even with this improvement, shrinking transistor geometry is leading to increased acquisition time, and the overlapping effect between adjacent nodes remains a critical issue. The resolution limit is an order of magnitude above the device feature densities in the &lt; 90nm era. The scaling down of transistor geometry is leading to the inevitable consequence where more than 50% of the transistors in 90nm process have widths smaller than 0.4um. The acquisition time of such nodes becomes unreasonably long. In order to examine nodes in a dense logic cuicuit, cross talk and convolution effects between neighboring signals also need to be considered. In this paper we will demonstrate the impact that these effects may have on modern design. In order to maintain the debug capability, with the currently available analytical tools for future technologies, conceptual modification of the FA process is required. This process should start on the IC design board where the VLSI designer should be familiar with FA constraints, and thus apply features that will enable enhanced FA capabilities to the circuit in hand during the electrical design or during the physical design stages. The necessity for reliable failure analysis in real-time should dictate that the designer of advanced VLSI blocks incorporates failure analysis constraints among other design rules. The purpose of this research is to supply the scientific basis for the optimal incorporation of design rules for optical probing in the &lt; 90nm gate era. Circuit designers are usually familiar with the nodes in the design which are critical for debug, and the type of measurement (logic or DC level) they require. The designer should enable the measurement of these signals by applying certain circuit and physical constraints. The implementation of these constraints may be done at the cell level, the block level or during the integration. We will discuss the solutions, which should be considered in order to mitigate tool limitations, and also to enable their use for next generation processes.

scholarly journals Nanofluid flow containing carbon nanotubes with quartic autocatalytic chemical reaction and Thompson and Troian slip at the boundary

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Muhammad Ramzan ◽  
Jae Dong Chung ◽  
Seifedine Kadry ◽  
Yu-Ming Chu ◽  
Muhammad Akhtar
Keyword(s):  
Mathematical Model ◽  
Carbon Nanotubes ◽  
Drag Force ◽  
Chemical Reaction ◽  
Slip Velocity ◽  
Volume Fraction ◽  
Surface Drag ◽  
Nanofluid Flow ◽  
Velocity Parameter ◽  
The Impact

Abstract A mathematical model is envisioned to discourse the impact of Thompson and Troian slip boundary in the carbon nanotubes suspended nanofluid flow near a stagnation point along an expanding/contracting surface. The water is considered as a base fluid and both types of carbon nanotubes i.e., single-wall (SWCNTs) and multi-wall (MWCNTs) are considered. The flow is taken in a Dacry-Forchheimer porous media amalgamated with quartic autocatalysis chemical reaction. Additional impacts added to the novelty of the mathematical model are the heat generation/absorption and buoyancy effect. The dimensionless variables led the envisaged mathematical model to a physical problem. The numerical solution is then found by engaging MATLAB built-in bvp4c function for non-dimensional velocity, temperature, and homogeneous-heterogeneous reactions. The validation of the proposed mathematical model is ascertained by comparing it with a published article in limiting case. An excellent consensus is accomplished in this regard. The behavior of numerous dimensionless flow variables including solid volume fraction, inertia coefficient, velocity ratio parameter, porosity parameter, slip velocity parameter, magnetic parameter, Schmidt number, and strength of homogeneous/heterogeneous reaction parameters are portrayed via graphical illustrations. Computational iterations for surface drag force are tabulated to analyze the impacts at the stretched surface. It is witnessed that the slip velocity parameter enhances the fluid stream velocity and diminishes the surface drag force. Furthermore, the concentration of the nanofluid flow is augmented for higher estimates of quartic autocatalysis chemical.

scholarly journals Low-carbon cast microalloyed steel intercritically heat-treated at different temperatures: microstructure and mechanical properties

2021 ◽  
Vol 21 (2) ◽  
Author(s):  
Hadi Torkamani ◽  
Shahram Raygan ◽  
Carlos Garcia Mateo ◽  
Yahya Palizdar ◽  
Jafar Rassizadehghani ◽  
...  
Keyword(s):  
Carbon Content ◽  
Volume Fraction ◽  
Block Size ◽  
Tensile Tests ◽  
Total Elongation ◽  
Martensite Phase ◽  
Low Carbon ◽  
Steel Increase ◽  
Different Temperatures ◽  
The Impact

AbstractIn this study, dual-phase (DP, ferrite + martensite) microstructures were obtained by performing intercritical heat treatments (IHT) at 750 and 800 °C followed by quenching. Decreasing the IHT temperature from 800 to 750 °C leads to: (i) a decrease in the volume fraction of austenite (martensite after quenching) from 0.68 to 0.36; (ii) ~ 100 °C decrease in martensite start temperature (Ms), mainly due to the higher carbon content of austenite and its smaller grains at 750 °C; (iii) a reduction in the block size of martensite from 1.9 to 1.2 μm as measured by EBSD. Having a higher carbon content and a finer block size, the localized microhardness of martensite islands increases from 380 HV (800 °C) to 504 HV (750 °C). Moreover, despite the different volume fractions of martensite obtained in DP microstructures, the hardness of the steels remained unchanged by changing the IHT temperature (~ 234 to 238 HV). Applying lower IHT temperature (lower fraction of martensite), the impact energy even decreased from 12 to 9 J due to the brittleness of the martensite phase. The results of the tensile tests indicate that by increasing the IHT temperature, the yield and ultimate tensile strengths of the DP steel increase from 493 to 770 MPa, and from 908 to 1080 MPa, respectively, while the total elongation decreases from 9.8 to 4.5%. In contrast to the normalized sample, formation of martensite in the DP steels could eliminate the yield point phenomenon in the tensile curves, as it generates free dislocations in adjacent ferrite.

scholarly journals Lasting effects of prenatal exposure to Cannabis in the retina of the offspring: an experimental study in mice

2021 ◽  
Vol 7 (1) ◽  
Author(s):  
Paulo Roberto Arruda Zantut ◽  
Mariana Matera Veras ◽  
Sarah Gomes Menezes Benevenutto ◽  
Angélica Mendonça Vaz Safatle ◽  
Ricardo Augusto Pecora ◽  
...  
Keyword(s):  
Young Adult ◽  
Light Microscopy ◽  
Prenatal Exposure ◽  
Structural Changes ◽  
Volume Fraction ◽  
Clinical Care ◽  
Retinal Layer ◽  
Exposed Population ◽  
The Central Nervous System ◽  
The Impact

Abstract Background Prenatal exposure to Cannabis is a worldwide growing problem. Although retina is part of the central nervous system, the impact of maternal Cannabis use on the retinal development and its postnatal consequences remains unknown. As the prenatal period is potentially sensitive in the normal development of the retina, we hypothesized that recreational use of Cannabis during pregnancy may alter retina structure in the offspring. To test this, we developed a murine model that mimics human exposure in terms of dose and use. Methods Pregnant BalbC mice were exposed daily for 5 min to Cannabis smoke (0.2 g of Cannabis) or filtered air, from gestational day 5 to 18 (N = 10/group). After weaning period, pups were separated and examined weekly. On days 60, 120, 200, and 360 after birth, 10 pups from each group were randomly selected for Spectral Domain Optical Coherence Tomography (SD-OCT) analysis of the retina. All retina layers were measured and inner, outer, and total retina thickness were calculated. Other 37 mice from both groups were sacrificed on days 20, 60, and 360 for retinal stereology (total volume of the retina and volume fraction of each retinal layer) and light microscopy. Means and standard deviations were calculated and MANOVA was performed. Results The retina of animals which mother was exposed to Cannabis during gestation was 17% thinner on day 120 (young adult) than controls (P = 0.003) due to 21% thinning of the outer retina (P = 0.001). The offspring of mice from the exposed group presented thickening of the IS/OS in comparison to controls on day 200 (P < 0.001). In the volumetric analyzes by retinal stereology, the exposed mice presented transitory increase of the IS/OS total volume and volume fraction on day 60 (young adult) compared to controls (P = 0.008 and P = 0.035, respectively). On light microscopy, exposed mice presented thickening of the IS/OS on day 360 (adult) compared to controls (P = 0.03). Conclusion Gestational exposure to Cannabis smoke may cause structural changes in the retina of the offspring that return to normal on mice adulthood. These experimental evidences suggest that children and young adults whose mothers smoked Cannabis during pregnancy may require earlier and more frequent clinical care than the non-exposed population.

scholarly journals Insulation Characteristics of Sisal Fibre/Epoxy Composites

2017 ◽  
Vol 2017 ◽  
pp. 1-6 ◽  
Author(s):  
A. Shalwan ◽  
M. Alajmi ◽  
A. Alajmi
Keyword(s):  
Volume Fraction ◽  
Fibre Volume Fraction ◽  
Thermal Characteristics ◽  
Fibre Volume ◽  
Point Of View ◽  
Natural Fibres ◽  
Epoxy Composites ◽  
Ongoing Research ◽  
Sisal Fibre ◽  
The Impact

Using natural fibres in civil engineering is the aim of many industrial and academics sectors to overcome the impact of synthetic fibres on environments. One of the potential applications of natural fibres composites is to be implemented in insulation components. Thermal behaviour of polymer composites based on natural fibres is recent ongoing research. In this article, thermal characteristics of sisal fibre reinforced epoxy composites are evaluated for treated and untreated fibres considering different volume fractions of 0–30%. The results revealed that the increase in the fibre volume fraction increased the insulation performance of the composites for both treated and untreated fibres. More than 200% insulation rate was achieved at the volume fraction of 20% of treated sisal fibres. Untreated fibres showed about 400% insulation rate; however, it is not recommended to use untreated fibres from mechanical point of view. The results indicated that there is potential of using the developed composites for insulation purposes.

Experimental Model of Temperature-Driven Nanofluid

2006 ◽  
Vol 129 (6) ◽  
pp. 697-704 ◽  
Author(s):  
A. G. Agwu Nnanna
Keyword(s):  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Small Volume ◽  
Volume Fraction ◽  
Convective Heat Transfer Coefficient ◽  
Isothermal Condition ◽  
Carrier Fluid ◽  
Small Volume Fraction ◽  
The Impact

This paper presents a systematic experimental method of studying the heat transfer behavior of buoyancy-driven nanofluids. The presence of nanoparticles in buoyancy-driven flows affects the thermophysical properties of the fluid and consequently alters the rate of heat transfer. The focus of this paper is to estimate the range of volume fractions that results in maximum thermal enhancement and the impact of volume fraction on Nusselt number. The test cell for the nanofluid is a two-dimensional rectangular enclosure with differentially heated vertical walls and adiabatic horizontal walls filled with 27 nm Al2O3–H2O nanofluid. Simulations were performed to measure the transient and steady-state thermal response of nanofluid to imposed isothermal condition. The volume fraction is varied between 0% and 8%. It is observed that the trend of the temporal and spatial evolution of temperature profile for the nanofluid mimics that of the carrier fluid. Hence, the behaviors of both fluids are similar. Results shows that for small volume fraction, 0.2⩽ϕ⩽2% the presence of the nanoparticles does not impede the free convective heat transfer, rather it augments the rate of heat transfer. However, for large volume fraction ϕ>2%, the convective heat transfer coefficient declines due to reduction in the Rayleigh number caused by increase in kinematic viscosity. Also, an empirical correlation for Nuϕ as a function of ϕ and Ra has been developed, and it is observed that the nanoparticle enhances heat transfer rate even at a small volume fraction.

Thermo-Solutal Convection of a Nanofluid Utilizing Fourier’s-Type Compass Conditions

2020 ◽  
Vol 9 (4) ◽  
pp. 362-374
Author(s):  
J. C. Umavathi ◽  
Ali J. Chamkha
Keyword(s):  
Brownian Motion ◽  
Prandtl Number ◽  
Boundary Conditions ◽  
Volume Fraction ◽  
Temperature Fields ◽  
Physical Parameters ◽  
Surface Boundary ◽  
Perturbation Scheme ◽  
Runge Kutta ◽  
The Impact

Nanotechnology has infiltrated into duct design in parallel with many other fields of mechanical, medical and energy engineering. Motivated by the excellent potential of nanofluids, a subset of materials engineered at the nanoscale, in the present work, a new mathematical model is developed for natural convection in a vertical duct containing nanofluid. Numerical scrutiny for the double-diffusive free and forced convection within a duct encumbered with nanofluid is performed. Buongiorno’s model is deployed to define the nanofluid. Robin boundary conditions are used to define the surface boundary conditions. Thermal and concentration equations envisage the viscous, Brownian motion, thermosphores of the nanofluid, Soret and Dufour effects. Using the Boussi-nesq approximation the solutal buoyancy effect as a result of gradients in concentration are incorporated. The conservation equations which are nonlinear are numerically estimated using fourth order Runge-Kutta methodology and analytically ratifying regular perturbation scheme. The mass, heat, nanoparticle concentration and species concentration fields on eight dimensionless physical parameters such as thermal and mass Grashof numbers, Brownian motion parameter, thermal parameter, Prandtl number, Eckert number, Schmidt parameter, and Soret parameter are calculated. The impact of these parameters are outlined pictorially. The velocity and temperature fields are boosted with the thermal Grashof number. The Soret and the Schemidt parameters reduces the nanoparticle volume fraction but it heightens the momentum, temperature and concentration. At the cold wall thermal and concentration Grashof numbers reduces the Nusselt values but they increase the Nusselt values at the hot wall. The reversal consequence was attained at the hot plate. The perturbation and Runge-Kutta solutions are equal in the nonappearance of Prandtl number. The (E. Zanchini, Int. J. Heat Mass Transfer 41, 3949 (1998)). results are restored for the regular fluid. The heat transfer rate is high for nanofluid when matched with regular fluid.

Sign in / Sign up

Export Citation Format

Share Document