Ground displacements revealed by A-DInSAR analysis in the Germano iron mining complex before and after the Fundão Dam collapse using Sentinel-1 data

2021 ◽  
Vol 15 (03) ◽  
Author(s):  
José C. Mura ◽  
Fabio F. Gama ◽  
Waldir R. Paradella ◽  
Cleber G. de Oliveira ◽  
Thiago G. Rodrigues
Author(s):  
Hamid Karimian ◽  
Pete Barlow ◽  
Chris Blackwell ◽  
Chris Campbell

Abstract The Wapiti River South Slope (the Slope) near Grand Prairie, Alberta, Canada, is 500 m long and consists of a steep lower slope and a shallower upper slope. Both the upper and the lower slopes are located within a landslide complex with ground movements of varying magnitudes and depths. The Alliance Pipeline (Alliance) NPS 42 Mainline (the pipeline) was installed in the winter of 2000 using conventional trenching techniques at an angle of approximately 8° to the slope fall line. Evidence of slope instability was observed in the slope since 2007. The surficial geology of the slope comprises a colluvium layer draped over bedrock formation in the lower slope, and glacial deposits in the upper slope. Available data indicated two different slide mechanisms. In the lower slope, there is a shallow translational slide within a colluvium layer, and in the upper slope there is a deep-seated translational slide within the glacial deposits. Both the upper and lower slope landslides have been confirmed to be active in the past decade. Gradual ground displacements in the order of several centimeters per year were observed in both the upper and lower slopes between 2007 and 2012. Large ground displacements in the order of several meters were observed between 2012 and 2014 in the lower slope that led to the first stress relief and subsequent slope mitigation measures in the spring and summer of 2014. Monitoring of the slope after mitigations indicated significant reduction in the rate of ground movement in the lower slope. Surveying of the pipeline before and after stress relief indicated an increase in lateral pipeline deformation in the direction of ground movement, following the stress relief. This observation raised questions regarding the effectiveness of partial stress relief to reduce stresses and strains associated with ground movements. Finite element analysis (FEA) was conducted in 2016 to aid in assessing the condition of the pipeline after being subject to ground displacements prior to 2014, stress relief in 2014, and subsequent ground displacement from July 2014 to December 2016. The results and findings of the FEA reasonably matched the observed pipeline behaviour before and after stress relief in the lower slope. The FEA results demonstrated that while the lateral displacement of the pipeline, originally caused by ground movement, increased following the removal of the soil loading during the stress relief, the maximum pipeline strain was reduced within the excavated portion. The FEA was also employed to assess the pipeline response to potential ground displacement scenarios following December 2016. For this assessment, three ground displacement scenarios that comprise different lengths of the pipeline were analyzed. An increased rate of ground displacement, with a pattern that matched one of the analyzed scenarios, was observed in the upper slope in the spring of 2017. The results of FEA were used to assess the pipeline response to the increased rate of displacement in the upper slope. Subsequently a decision was made to stress-relieve the pipeline. The second stress-relief was conducted in the summer of 2017. This stress relief was conducted locally at the toe and head of the active slide in the upper slope, where the FEA showed the greatest stress concentrations in the pipeline.


Author(s):  
Markus Gastauer ◽  
Wilson R. Nascimento ◽  
Cecílio Frois Caldeira ◽  
Silvio Junio Ramos ◽  
Pedro Walfir M. Souza-Filho ◽  
...  

Author(s):  
J. Temple Black

Tool materials used in ultramicrotomy are glass, developed by Latta and Hartmann (1) and diamond, introduced by Fernandez-Moran (2). While diamonds produce more good sections per knife edge than glass, they are expensive; require careful mounting and handling; and are time consuming to clean before and after usage, purchase from vendors (3-6 months waiting time), and regrind. Glass offers an easily accessible, inexpensive material ($0.04 per knife) with very high compressive strength (3) that can be employed in microtomy of metals (4) as well as biological materials. When the orthogonal machining process is being studied, glass offers additional advantages. Sections of metal or plastic can be dried down on the rake face, coated with Au-Pd, and examined directly in the SEM with no additional handling (5). Figure 1 shows aluminum chips microtomed with a 75° glass knife at a cutting speed of 1 mm/sec with a depth of cut of 1000 Å lying on the rake face of the knife.


Author(s):  
R. F. Bils ◽  
W. F. Diller ◽  
F. Huth

Phosgene still plays an important role as a toxic substance in the chemical industry. Thiess (1968) recently reported observations on numerous cases of phosgene poisoning. A serious difficulty in the clinical handling of phosgene poisoning cases is a relatively long latent period, up to 12 hours, with no obvious signs of severity. At about 12 hours heavy lung edema appears suddenly, however changes can be seen in routine X-rays taken after only a few hours' exposure (Diller et al., 1969). This study was undertaken to correlate these early changes seen by the roengenologist with morphological alterations in the lungs seen in the'light and electron microscopes.Forty-two adult male and female Beagle dogs were selected for these exposure experiments. Treated animals were exposed to 94.5-107-5 ppm phosgene for 10 min. in a 15 m3 chamber. Roentgenograms were made of the thorax of each animal before and after exposure, up to 24 hrs.


Author(s):  
M. H. Wheeler ◽  
W. J. Tolmsoff ◽  
A. A. Bell

(+)-Scytalone [3,4-dihydro-3,6,8-trihydroxy-l-(2Hj-naphthalenone] and 1,8-di- hydroxynaphthalene (DHN) have been proposed as intermediates of melanin synthesis in the fungi Verticillium dahliae (1, 2, 3, 4) and Thielaviopsis basicola (4, 5). Scytalone is enzymatically dehydrated by V. dahliae to 1,3,8-trihydroxynaphthalene which is then reduced to (-)-vermelone [(-)-3,4- dihydro-3,8-dihydroxy-1(2H)-naphthalenone]. Vermelone is subsequently dehydrated to DHN which is enzymatically polymerized to melanin.Melanin formation in Curvularia sp., Alternaria sp., and Drechslera soro- kiniana was examined by light and electron-transmission microscopy. Wild-type isolates of each fungus were compared with albino mutants before and after treatment with 1 mM scytalone or 0.1 mM DHN in 50 mM potassium phosphate buffer, pH 7.0. Both chemicals were converted to dark pigments in the walls of hyphae and conidia of the albino mutants. The darkened cells were similar in appearance to corresponding cells of the wild types under the light microscope.


Author(s):  
T. Gulik-Krzywicki ◽  
M.J. Costello

Freeze-etching electron microscopy is currently one of the best methods for studying molecular organization of biological materials. Its application, however, is still limited by our imprecise knowledge about the perturbations of the original organization which may occur during quenching and fracturing of the samples and during the replication of fractured surfaces. Although it is well known that the preservation of the molecular organization of biological materials is critically dependent on the rate of freezing of the samples, little information is presently available concerning the nature and the extent of freezing-rate dependent perturbations of the original organizations. In order to obtain this information, we have developed a method based on the comparison of x-ray diffraction patterns of samples before and after freezing, prior to fracturing and replication.Our experimental set-up is shown in Fig. 1. The sample to be quenched is placed on its holder which is then mounted on a small metal holder (O) fixed on a glass capillary (p), whose position is controlled by a micromanipulator.


Author(s):  
R. M. Anderson

Aluminum-copper-silicon thin films have been considered as an interconnection metallurgy for integrated circuit applications. Various schemes have been proposed to incorporate small percent-ages of silicon into films that typically contain two to five percent copper. We undertook a study of the total effect of silicon on the aluminum copper film as revealed by transmission electron microscopy, scanning electron microscopy, x-ray diffraction and ion microprobe techniques as a function of the various deposition methods.X-ray investigations noted a change in solid solution concentration as a function of Si content before and after heat-treatment. The amount of solid solution in the Al increased with heat-treatment for films with ≥2% silicon and decreased for films <2% silicon.


Author(s):  
T. C. Tisone ◽  
S. Lau

In a study of the properties of a Ta-Au metallization system for thin film technology application, the interdiffusion between Ta(bcc)-Au, βTa-Au and Ta2M-Au films was studied. Considered here is a discussion of the use of the transmission electron microscope(TEM) in the identification of phases formed and characterization of the film microstructures before and after annealing.The films were deposited by sputtering onto silicon wafers with 5000 Å of thermally grown oxide. The film thicknesses were 2000 Å of Ta and 2000 Å of Au. Samples for TEM observation were prepared by ultrasonically cutting 3mm disks from the wafers. The disks were first chemically etched from the silicon side using a HNO3 :HF(19:5) solution followed by ion milling to perforation of the Au side.


Author(s):  
P.A. Crozier

Absolute inelastic scattering cross sections or mean free paths are often used in EELS analysis for determining elemental concentrations and specimen thickness. In most instances, theoretical values must be used because there have been few attempts to determine experimental scattering cross sections from solids under the conditions of interest to electron microscopist. In addition to providing data for spectral quantitation, absolute cross section measurements yields useful information on many of the approximations which are frequently involved in EELS analysis procedures. In this paper, experimental cross sections are presented for some inner-shell edges of Al, Cu, Ag and Au.Uniform thin films of the previously mentioned materials were prepared by vacuum evaporation onto microscope cover slips. The cover slips were weighed before and after evaporation to determine the mass thickness of the films. The estimated error in this method of determining mass thickness was ±7 x 107g/cm2. The films were floated off in water and mounted on Cu grids.


Author(s):  
Ray Wu ◽  
G. Ruben ◽  
B. Siegel ◽  
P. Spielman ◽  
E. Jay

A method for determining long nucleotide sequences of double-stranded DNA is being developed. It involves (a) the synchronous digestion of the DNA from the 3' ends with EL coli exonuclease III (Exo III) followed by (b) resynthesis with labeled nucleotides and DNA polymerase. A crucial factor in the success of this method is the degree to which the enzyme digestion proceeds synchronously under proper conditions of incubation (step a). Dark field EM is used to obtain accurate measurements on the lengths and distribution of the DNA molecules before and after digestion with Exo III, while gel electrophoresis is used in parallel to obtain a mean length for these molecules. It is the measurements on a large enough sample of individual molecules by EM that provides the information on how synchronously the digestion proceeds. For length measurements, the DNA molecules were picked up on 20-30 Å thick carbon-aluminum films, using the aqueous Kleinschmidt technique and stained with 7.5 x 10-5M uranyl acetate in 90% ethanol for 3 minutes.


Sign in / Sign up

Export Citation Format

Share Document