scholarly journals Nanoscale stacking fault–assisted room temperature plasticity in flash-sintered TiO2

2019 ◽  
Vol 5 (9) ◽  
pp. eaaw5519 ◽  
Author(s):  
Jin Li ◽  
Jaehun Cho ◽  
Jie Ding ◽  
Harry Charalambous ◽  
Sichuang Xue ◽  
...  
Keyword(s):  
Room Temperature ◽  
Oxygen Vacancies ◽  
Crack Formation ◽  
High Stress ◽  
Ceramic Materials ◽  
Sintering Process ◽  
Flash Sintering ◽  
Structural Applications ◽  
Deformation Behaviors

Ceramic materials have been widely used for structural applications. However, most ceramics have rather limited plasticity at low temperatures and fracture well before the onset of plastic yielding. The brittle nature of ceramics arises from the lack of dislocation activity and the need for high stress to nucleate dislocations. Here, we have investigated the deformability of TiO2 prepared by a flash-sintering technique. Our in situ studies show that the flash-sintered TiO2 can be compressed to ~10% strain under room temperature without noticeable crack formation. The room temperature plasticity in flash-sintered TiO2 is attributed to the formation of nanoscale stacking faults and nanotwins, which may be assisted by the high-density preexisting defects and oxygen vacancies introduced by the flash-sintering process. Distinct deformation behaviors have been observed in flash-sintered TiO2 deformed at different testing temperatures, ranging from room temperature to 600°C. Potential mechanisms that may render ductile ceramic materials are discussed.

Preparation and Characterization of SiC/MoSi2 Composites from Powder Resulting from a Mechanical-Assistant Combustion Synthesis Method

2010 ◽  
Vol 105-106 ◽  
pp. 70-74
Author(s):  
Jian Guang Xu ◽  
Hui Qiang Li ◽  
Hou An Zhang
Keyword(s):  
Mechanical Properties ◽  
Cyclic Oxidation ◽  
Room Temperature ◽  
Synthesis Method ◽  
Pressureless Sintering ◽  
Sintering Process ◽  
Oxidation Properties ◽  
Mosi2 Composite

SiC reinforced MoSi2 composites have been successfully prepared by pressureless sintering from mechanical-assistant combustion synthesized powders. The sintering temperatures and holding time were 1500°C~1650°C at a heating rate of 10K/min and 1 hour, respectively. The microstructure and mechanical properties of the as-sintered composites were investigated. SEM micrographs of SiC/MoSi2 composites showed that SiC particles were homogeneously distributed in MoSi2 matrix. The Vickers hardness, flexural strength and fracture toughness of the SiC/MoSi2 composites were up to 15.50GPa, 468.7MPa and 9.35MPa•m1/2, respectively. The morphologies of fractured surface of the composites revealed the mechanism to improve mechanical properties of MoSi2 matrix. At last, the cyclic oxidation behavior of the composites was discussed. The results of this work showed that in situ SiC/MoSi2 composite powder prepared by MASHS technique could be successfully sintered via pressureless sintering process and significant improvement of room temperature mechanical and anti-oxidation properties could be achieved.

Synthesis of SiCW/(Mo,W)Si2 Composite by the "Chemical Oven" Self-Propagating Combustion Method

2008 ◽  
Vol 368-372 ◽  
pp. 951-954 ◽  
Author(s):  
Jian Guang Xu ◽  
Hou An Zhang ◽  
Guo Jian Jiang ◽  
Wen Lan Li
Keyword(s):  
Solid Solution ◽  
Flexural Strength ◽  
Room Temperature ◽  
Composite Powder ◽  
Cost Effective ◽  
Combustion Method ◽  
Sintering Process ◽  
High Temperature Synthesis ◽  
Result Show

SiC whisker reinforced (Mo,W)Si2 composite powder has been successfully synthesized by a novel process, named as chemical oven self-propagating high temperature synthesis (COSHS). The mixtures of Si and Ti powders were ignited as chemical oven. XRD result shows that the combustion product is mainly composed of (Mo,W)Si2 solid solution and SiC phases. SEM photo and EDS result show that SiC whisker is formed during this process. The as-prepared SiCW/(Mo,W)Si2 composite powder has been pressureless sintered. The microstructure and mechanical properties of the composite were investigated. Relative densities of the monolithic material and composite are 91.2% and 92.2%, respectively. The composite containing SiC whisker and (Mo,W)Si2 solid solution has higher Vickers hardness than monolithic MoSi2. Especially the room-temperature flexural strength of the composite is higher than that of monolithic MoSi2, from 135.5MPa for MoSi2 to 235.6MPa for composites with 10 vol.% WSi2 and 15 vol.% SiC, increased by 73.9%. The morphology of fractured surface of composite reveals the mechanism to improve flexural strength of MoSi2. The results of this work show that in situ SiCW/(Mo,W)Si2 composite powder prepared by COSHS technique could be successfully sintered via pressureless sintering process and significant improvement of room temperature flexural strength could be achieved. It could be a cost-effective process for industry in future applications.

Microstructures and Mechanical Properties of NiAl+Mo In-Situ Eutectic Composites

1990 ◽  
Vol 194 ◽  
Author(s):  
P. R. Subramanian ◽  
M. G. Mendiratta ◽  
D. B. Miracle ◽  
D. M. Dimiduk
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Room Temperature ◽  
Composite System ◽  
Elevated Temperatures ◽  
Two Phase ◽  
Structural Applications ◽  
Temperature Fracture

AbstractThe quasibinary NiAI-Mo system exhibits a large two-phase field between NiAl and the terminal (Mo) solid solution, and offers the potential for producing in-situ eutectic composites for high-temperature structural applications. The phase stability of this composite system was experimentally evaluated, following long-term exposures at elevated temperatures. Bend strengths as a function of temperature and room-temperature fracture toughness data are presented for selected NiA1-Mo alloys, together with results from fractography observations.

Synthesis of Al2O3-Ni3Al Cermets by Room-Temperature Ball Milling of Al, Ni and Al2O3 Mixtures

2006 ◽  
Vol 509 ◽  
pp. 123-128
Author(s):  
Enrique Rocha-Rangel ◽  
M.S. Moreno-Guerrero ◽  
A. Velásquez-Naranjo ◽  
Elizabeth Refugio-García
Keyword(s):  
Ball Milling ◽  
Room Temperature ◽  
Exothermic Reaction ◽  
Inert Atmosphere ◽  
Reactive Sintering ◽  
Sintering Process ◽  
Interpenetrating Networks ◽  
Heat Treated ◽  
Ni3al Intermetallic

The synthesis of Al2O3-Ni3Al cermets with interpenetrating networks has been performed via a pressureless reactive sintering process. The synthesis has been induced by means of a solidstate reaction of Al + Ni + Al2O3 powders under intensive ball milling. The mixtures have been heat treated in an inert atmosphere (N2) in order to control the exothermic reaction between Ni and Al, with special care at temperatures near the melting point of Al. Dense and homogeneous microstructures have been obtained, composed by a matrix of Al2O3 reinforced with a Ni3Al intermetallic. Thermodynamic calculations indicate that such a cermet can be fabricated by in situ reaction synthesis. This suggests that a pressureless reaction sintering process may be a general route to synthesizing cermets with the prospect for the production of cermets with interpenetrating networks.

Extreme Room Temperature Compression and Bending in Ferroelectric Oxide Pillars

2021 ◽  
Author(s):  
Ying Liu ◽  
Xiangyuan Cui ◽  
Ranming Niu ◽  
Shujun Zhang ◽  
Xiaozhou Liao ◽  
...  
Keyword(s):  
Plastic Deformation ◽  
Room Temperature ◽  
Oxygen Vacancies ◽  
Ceramic Materials ◽  
Perovskite Oxide ◽  
High Concentration ◽  
Bending Tests ◽  
Ionic Bonds ◽  
Order Of Magnitude ◽  
Mn Doped

Abstract Plastic deformation in ceramic materials is normally only observed in nanometre-sized samples. However, we have observed unprecedented levels of plasticity (>50% plastic strain) and excellent elasticity (6% elastic strain) in perovskite oxide Pb(In1/2Nb1/2)O3-Pb(Mg1/3Nb2/3)O3-PbTiO3 (PIN-PMN-PT), under compression along <100>pc pillars up to 2.1 μm in diameter. The extent of this deformation is much higher than has previously been reported for ceramic materials, and the sample size at which plasticity is observed is almost an order of magnitude larger. Bending tests also revealed over 8% flexural strain. Plastic deformation occurred by slip along {110} <110>. Calculations indicate that the resulting strain gradients will give rise to extreme flexoelectric polarization. First principles models predict that a high concentration of oxygen vacancies (Vo) weaken the covalent/ionic bonds, giving rise to the unexpected plasticity. Mechanical testing on Vo-rich Mn-doped PIN-PMN-PT confirmed this prediction. These findings will facilitate the design of plastic ceramic materials and the development of flexoelectric-based nano-electromechanical systems.

High pressure compaction of nanosize ceramic powders

1997 ◽  
Vol 12 (3) ◽  
pp. 764-768 ◽  
Author(s):  
M. R. Gallas ◽  
A. R. Rosa ◽  
T. H. Costa ◽  
J. A. H. da Jornada
Keyword(s):  
High Pressure ◽  
Room Temperature ◽  
Ceramic Materials ◽  
High Density ◽  
Full Density ◽  
Pressure Curve ◽  
Sintering Process ◽  
Ceramic Powders ◽  
Special Configuration ◽  
First Time

High-density ceramic materials from nanosize ceramic powders were produced by high pressure under nearly hydrostatic environment up to 5.6 GPa, on a special configuration in a toroidal-type apparatus, at room temperature. Attempts to use a common solid pressure transmitting medium, as NaCl, resulted in cracked samples. Lead and indium, which have an extremely low shear strength, proved to be the suitable choices as a pressure-transmitting medium to compact these ceramic materials, in order to obtain high-density samples. Transparent amorphous SiO2-gel and translucent γ−Al2O3 samples, in bulk, with volumes about 40 mm3, hard and crack-free were obtained. Densities over 90% of full density for the γ−Al2O3 samples and over 80% for the compacted SiO2-gel samples were obtained. In addition, from the density-pressure curve, the yield strength (σ) for γ−Al2O3 was estimated, for the first time, as 2.6 GPa. Vickers microhardness values were in the range of 5.7 GPa for the γ−Al2O3 samples, and 4.0 GPa for the SiO2-gel samples, under loads of 50 g. An important and practical application of these results is the possibility of producing bulk γ−Al2O3, a new alumina material, which was not possible to prepare before due to the conversion to a phase during the normal sintering process. Additionally, specially for SiO2-gel, a very important application of this study is the possibility of incorporation of organic substances in an inorganic matrix, using high pressure at room temperature.

Controlling microstructural evolution to in situ toughen and strengthen silicon carbide

1996 ◽  
Vol 54 ◽  
pp. 692-693 ◽  
Author(s):  
Warren J. MoberlyChan ◽  
J. J. Cao ◽  
L. C. DeJonghe
Keyword(s):  
Crack Propagation ◽  
Room Temperature ◽  
Grain Shape ◽  
Secondary Phase ◽  
Fracture Path ◽  
Secondary Phases ◽  
Structural Applications ◽  
Temperature Fracture ◽  
Nonoxide Ceramics

Nonoxide ceramics are desirable for high temperature structural applications, however, they have typically exhibited inferior room temperature fracture toughness. Similar to processing developments to toughen Si3N4, SiC has recently been processed via control of a phase transformation to produce in situ toughened microstructures. An elongated grain shape, coupled with a tortuous fracture path around grains, can provide bridging behind an advancing crack tip, which increases the crack resistance (rising R curve) and halts crack propagation. Most in situ toughened nonoxide ceramics incorporate upwards of 10-20% secondary phase(s), which simplifies crack propagation through this weaker phase to improve toughness, but typically at the expense of substantially reducing strength at high temperatures. The ABC-SiC in this study can be processed with <3% secondary phases and consequently exhibits record toughness and higher strength than commercial (Hexoloy SA) SiC.

scholarly journals Insight into the BiFeO3 flash sintering process by in-situ energy dispersive X-ray diffraction (ED-XRD)

2019 ◽  
Vol 45 (2) ◽  
pp. 2828-2834 ◽  
Author(s):  
Luis A. Perez-Maqueda ◽  
Eva Gil-Gonzalez ◽  
Mary Anne Wassel ◽  
Shikhar K. Jha ◽  
Antonio Perejon ◽  
...  
Keyword(s):  
Energy Dispersive ◽  
Sintering Process ◽  
X Ray Diffraction ◽  
X Ray ◽  
Flash Sintering ◽  
Insight Into

Crystallization sequence of an A1N-Y2O3-SiO2 glass-ceramic

1986 ◽  
Vol 44 ◽  
pp. 446-447
Author(s):  
T.R. Dinger ◽  
G. Thomas
Keyword(s):  
High Temperature ◽  
Glass Ceramic ◽  
Crystallization Behavior ◽  
High Stress ◽  
Crystallization Sequence ◽  
Sio2 Glass ◽  
Structural Applications ◽  
Ceramic Precursors

The use of Si3N4, alloys for high temperature, high stress structural applications has prompted numerous studies of the oxynitride glasses which exist as intergranular phases in their microstructures. Oxynitride glasses have been investigated recently in their bulk form in order to understand their crystallization behavior for subsequent Si3N4 applications and to investigate their worth as glass-ceramic precursors. This research investigates the crystallization sequence of a glass having a normalized composition of Y26Si30Al11 ON11 and lying in the A1N-Y2O3-SiO2 section of the Y-Si-Al-O-N system. Such glasses exist as intergranular phases in the technologically important Y2O3/Al2O3-fluxed Si3N4 alloys.

Analytical and High-Resolution EM Study of Crystalline Phases formed at Metal-Ceramic Interface

1990 ◽  
Vol 48 (2) ◽  
pp. 426-427
Author(s):  
N. Merk ◽  
A. P. Tomsia ◽  
G. Thomas
Keyword(s):  
Cross Section ◽  
Dissimilar Materials ◽  
Ceramic Materials ◽  
Electron Micrograph ◽  
Scanning Electron Micrograph ◽  
Structural Applications ◽  
Metal Ceramic ◽  
The Subject ◽  
Ceramic Compounds ◽  
Scanning Electron

A recent development of new ceramic materials for structural applications involves the joining of ceramic compounds to metals. Due to the wetting problem, an interlayer material (brazing alloy) is generally used to achieve the bonding. The nature of the interfaces between such dissimilar materials is the subject of intensive studies and is of utmost importance to obtain a controlled microstructure at the discontinuities to satisfy the demanding properties for engineering applications . The brazing alloy is generally ductile and hence, does not readily fracture. It must also wett the ceramic with similar thermal expansion coefficient to avoid large stresses at joints. In the present work we study mullite-molybdenum composites using a brazing alloy for the weldment.A scanning electron micrograph from the cross section of the joining sequence studied here is presented in Fig. 1.

Sign in / Sign up

Export Citation Format

Share Document