scholarly journals Analytic Model for Conduction Current in AlGaN/GaN HFETs/HEMTs

2012 ◽  
Vol 2012 ◽  
pp. 1-11 ◽  
Author(s):  
Danqiong Hou ◽  
Griff L. Bilbro ◽  
Robert J. Trew
Keyword(s):  
Parameter Extraction ◽  
New Physics ◽  
Operating Conditions ◽  
Compact Modeling ◽  
Large Signal ◽  
New Model ◽  
Industry Standard ◽  
Rf Performance ◽  
Microwave Power Amplifier ◽  
Good Agreement

We have developed a new, zone-based compact physics-based AlGaN/GaN heterojunction field-effect transistor (HFET) model suitable for use in commercial harmonic-balance microwave circuit simulators. The new model is programmed in Verilog-A, an industry-standard compact modeling language. The new model permits the dc, small-signal, and large-signal RF performance for the transistor to be determined as a function of the device geometric structure and design features, material composition parameters, and dc and RF operating conditions. The new physics-based HFET model does not require extensive parameter extraction to determine model element values, as commonly employed for traditional equivalent-circuit-based transistor models. The new model has been calibrated and verified. We report very good agreement between simulated and measured dc and RF performance of an experimental C-band microwave power amplifier.

scholarly journals The Stationary Concentrated Vortex Model

Climate ◽  
2021 ◽  
Vol 9 (3) ◽  
pp. 39
Author(s):  
Oleg Onishchenko ◽  
Viktor Fedun ◽  
Wendell Horton ◽  
Oleg Pokhotelov ◽  
Natalia Astafieva ◽  
...  
Keyword(s):  
Vortex Structure ◽  
Radial Direction ◽  
Symmetry Axis ◽  
Outer Part ◽  
Vertical Direction ◽  
Axially Symmetric ◽  
New Model ◽  
Vortex Model ◽  
Axis Of Symmetry ◽  
Good Agreement

A new model of an axially-symmetric stationary concentrated vortex for an inviscid incompressible flow is presented as an exact solution of the Euler equations. In this new model, the vortex is exponentially localised, not only in the radial direction, but also in height. This new model of stationary concentrated vortex arises when the radial flow, which concentrates vorticity in a narrow column around the axis of symmetry, is balanced by vortex advection along the symmetry axis. Unlike previous models, vortex velocity, vorticity and pressure are characterised not only by a characteristic vortex radius, but also by a characteristic vortex height. The vortex structure in the radial direction has two distinct regions defined by the internal and external parts: in the inner part the vortex flow is directed upward, and in the outer part it is downward. The vortex structure in the vertical direction can be divided into the bottom and top regions. At the bottom of the vortex the flow is centripetal and at the top it is centrifugal. Furthermore, at the top of the vortex the previously ascending fluid starts to descend. It is shown that this new model of a vortex is in good agreement with the results of field observations of dust vortices in the Earth’s atmosphere.

scholarly journals Reliability-Aware SPICE Compatible Compact Modeling of IGZO Inverters on a Flexible Substrate

2021 ◽  
Vol 11 (11) ◽  
pp. 4838
Author(s):  
Je-Hyuk Kim ◽  
Youngjin Seo ◽  
Jun Tae Jang ◽  
Shinyoung Park ◽  
Dongyeon Kang ◽  
...  
Keyword(s):  
Flexible Electronics ◽  
Circuit Simulation ◽  
Flexible Substrate ◽  
Atomic Layer ◽  
Operating Conditions ◽  
Gate Insulator ◽  
Compact Modeling ◽  
Indium Gallium Zinc Oxide ◽  
Electrical Stress ◽  
Bending Radius

Accurate circuit simulation reflecting physical and electrical stress is of importance in indium gallium zinc oxide (IGZO)-based flexible electronics. In particular, appropriate modeling of threshold voltage (VT) changes in different bias and bending conditions is required for reliability-aware simulation in both device and circuit levels. Here, we present SPICE compatible compact modeling of IGZO transistors and inverters having an atomic layer deposition (ALD) Al2O3 gate insulator on a polyethylene terephthalate (PET) substrate. Specifically, the modeling was performed to predict the behavior of the circuit using stretched exponential function (SEF) in a bending radius of 10 mm and operating voltages ranging between 4 and 8 V. The simulation results of the IGZO circuits matched well with the measured values in various operating conditions. It is expected that the proposed method can be applied to process improvement or circuit design by predicting the direct current (DC) and alternating current (AC) responses of flexible IGZO circuits.

4-port RF performance assessment and compact modeling of UTBB-FDSOI transistors

2015 ◽  
Author(s):  
Jean-Charles Barbe ◽  
Luca Lucci ◽  
Alexandre Siligaris ◽  
Pierre Vincent ◽  
Olivier Faynot
Keyword(s):  
Performance Assessment ◽  
Compact Modeling ◽  
Rf Performance

scholarly journals Thermal conductivity of unsaturated clay-rocks

2010 ◽  
Vol 14 (1) ◽  
pp. 91-98 ◽  
Author(s):  
D. Jougnot ◽  
A. Revil
Keyword(s):  
Thermal Conductivity ◽  
Porous Material ◽  
Solid Phase ◽  
Model Parameters ◽  
Electrical Parameters ◽  
New Model ◽  
Unsaturated Clay ◽  
Unsaturated Porous Material ◽  
Clay Rocks ◽  
Good Agreement

Abstract. The parameters used to describe the electrical conductivity of a porous material can be used to describe also its thermal conductivity. A new relationship is developed to connect the thermal conductivity of an unsaturated porous material to the thermal conductivity of the different phases of the composite, and two electrical parameters called the first and second Archie's exponents. A good agreement is obtained between the new model and thermal conductivity measurements performed using packs of glass beads and core samples of the Callovo-Oxfordian clay-rocks at different saturations of the water phase. We showed that the three model parameters optimised to fit the new model against experimental data (namely the thermal conductivity of the solid phase and the two Archie's exponents) are consistent with independent estimates. We also observed that the anisotropy of the effective thermal conductivity of the Callovo-Oxfordian clay-rock was mainly due to the anisotropy of the thermal conductivity of the solid phase.

A New Heat Transfer Correlation for Supercritical RP-3 Flowing in Vertical Tubes

2017 ◽  
Author(s):  
Longyun Wang ◽  
Zhi Tao ◽  
Jianqin Zhu ◽  
Haiwang Li ◽  
Zeyuan Cheng
Keyword(s):  
Heat Transfer ◽  
Influence Factors ◽  
Hydrocarbon Fuel ◽  
Operating Conditions ◽  
Major Influence ◽  
Absolute Deviation ◽  
New Correlation ◽  
Vertical Tubes ◽  
Correction Terms ◽  
Good Agreement

A new empirical correlation for upward flowing supercritical aviation kerosene RP-3 in the vertical tubes is proposed. In order to obtain the database, numerical simulation with a four-component surrogate model on RP-3 and LS low Reynolds turbulence model in vertical circular tube has been performed. Tubes of diameter 2mm to 10mm are studied and operating conditions cover pressure from 3MPa to 6MPa. Heat flux is 500KW/m2, mass flow rate is 700kg/(m2·s). The numerical results on wall temperature distribution under various conditions are compared with experimental data and a good agreement is achieved. The existing correlations are summarized and classified into three categories. Three representative correlations of each category are selected out to evaluate the applicability in heat transfer of supercritical RP-3. The result shows that correlations concluded from water and carbon-dioxide do not perform well in predicting heat transfer of hydrocarbon fuel. The mean absolute deviation of them is up to 20% and predict about 80% of the entire database within 30% error bands. So a new correlation which is applicable to different working conditions for supercritical RP-3 is put forward. Gnielinski type has been adapted as the basis of the new correlation for its higher accuracy. In consideration of major influence factors of supercritical heat transfer, correction terms of density and buoyancy effect are added in. The new correlation has a MAD of 9.26%, predicting 90.6% of the entire database within ±15% error bands. The comparisons validate the applicability of the new correlation.

scholarly journals Contact angle of water on iron ore fines: Measurement and analysis

2015 ◽  
Vol 51 (1) ◽  
pp. 33-40 ◽  
Author(s):  
X.B. Huang ◽  
X X.W. ◽  
J.J. Song ◽  
C.G. Bai ◽  
R.D. Zhang ◽  
...  
Keyword(s):  
Contact Angle ◽  
Iron Ore ◽  
Contact Angles ◽  
Physical Parameters ◽  
Iron Ores ◽  
New Model ◽  
Pressure Method ◽  
Measurement And Analysis ◽  
Iron Ore Fines ◽  
Good Agreement

The relative contact angle (?RCA) for seven iron ore fines was measured by using Washburn Osmotic Pressure method under laboratory conditions. By choosing cyclohexane as the reference that can perfectly wet iron ore particles, the relative contact angles were measured and varied from 57? to 73?. With the volume % of goethite (?G) as the variable, a new model for relative contact angle was developed. The expected relative contact angle for pure goethite is about 56?, while that for goethite free samples is about 77?. Physical properties, such as surface morphology (SMI) and pore volume (Vpore) can influence the relative contact angle. The ?G can be expressed as a function of SMI and VPore. Thus, we inferred that the relative contact angle is a function of ?G for the iron ores used. The measured relative contact angles were found to be in good agreement (Radj 2 >0.97) with the calculated ones based on the research from Iveson, et al. (2004). Comparing with the model developed by Iveson et al.(2004), the new model for contact angle proposed in this paper is similar, but more detailed with two meaningful physical parameters. The modification of physicochemical properties on iron ores would be another topic in the further study on granulation.

scholarly journals Mechanics of spontaneously formed nanoblisters trapped by transferred 2D crystals

2018 ◽  
Vol 115 (31) ◽  
pp. 7884-7889 ◽  
Author(s):  
Daniel A. Sanchez ◽  
Zhaohe Dai ◽  
Peng Wang ◽  
Arturo Cantu-Chavez ◽  
Christopher J. Brennan ◽  
...  
Keyword(s):  
Scaling Law ◽  
New Physics ◽  
Adhesion Energy ◽  
Work Of Adhesion ◽  
Fourth Power ◽  
Layered Systems ◽  
Simple Scaling ◽  
Dynamics Simulations ◽  
2D Crystals ◽  
Good Agreement

Layered systems of 2D crystals and heterostructures are widely explored for new physics and devices. In many cases, monolayer or few-layer 2D crystals are transferred to a target substrate including other 2D crystals, and nanometer-scale blisters form spontaneously between the 2D crystal and its substrate. Such nanoblisters are often recognized as an indicator of good adhesion, but there is no consensus on the contents inside the blisters. While gas-filled blisters have been modeled and measured by bulge tests, applying such models to spontaneously formed nanoblisters yielded unrealistically low adhesion energy values between the 2D crystal and its substrate. Typically, gas-filled blisters are fully deflated within hours or days. In contrast, we found that the height of the spontaneously formed nanoblisters dropped only by 20–30% after 3 mo, indicating that probably liquid instead of gas is trapped in them. We therefore developed a simple scaling law and a rigorous theoretical model for liquid-filled nanoblisters, which predicts that the interfacial work of adhesion is related to the fourth power of the aspect ratio of the nanoblister and depends on the surface tension of the liquid. Our model was verified by molecular dynamics simulations, and the adhesion energy values obtained for the measured nanoblisters are in good agreement with those reported in the literature. This model can be applied to estimate the pressure inside the nanoblisters and the work of adhesion for a variety of 2D interfaces, which provides important implications for the fabrication and deformability of 2D heterostructures and devices.

Numerical Analysis of the Flow Inside a Centrifugal Compressor’s Vaneless Diffuser and Volute

2001 ◽  
Author(s):  
Hooman Rezaei ◽  
Abraham Engeda ◽  
Paul Haley
Keyword(s):  
Experimental Data ◽  
Numerical Analysis ◽  
Mass Flow ◽  
Operating Conditions ◽  
Vaneless Diffuser ◽  
Flow Angle ◽  
Flow Rates ◽  
Mass Flow Rates ◽  
Minimum Medium ◽  
Good Agreement

Abstract The objective of this work was to perform numerical analysis of the flow inside a modified single stage CVHF 1280 Trane centrifugal compressor’s vaneless diffuser and volute. Gambit was utilized to read the casing geometry and generating the vaneless diffuser. An unstructured mesh was generated for the path from vaneless diffuser inlet to conic diffuser outlet. At the same time a meanline analysis was performed corresponding to speeds and mass flow rates of the experimental data in order to obtain the absolute velocity and flow angle leaving the impeller for those operating conditions. These values and experimental data were used as inlet and outlet boundary conditions for the simulations. Simulations were performed in Fluent 5.0 for three speeds of 2000, 3000 and 3497 RPM and mass flow rates of minimum, medium and maximum. Results are in good agreement with the experimental ones and present the flow structures inside the vaneless diffuser and volute.

A Confrontation of Lattice Boltzmann, Finite Difference and Taguchi Experimental Design Results for Optimizing Plasma Spraying Operating Conditions Toward Deposit Requirements

2017 ◽  
Vol 6 (4) ◽  
pp. 16-34 ◽  
Author(s):  
Ridha Djebali
Keyword(s):  
Experimental Design ◽  
Plasma Spraying ◽  
Lattice Boltzmann ◽  
Operating Conditions ◽  
Taguchi Experimental Design ◽  
Confirmation Test ◽  
Boltzmann Method ◽  
Impact Characteristics ◽  
Plasma Spraying Process ◽  
Good Agreement

The aim of the present work is the confrontation of three numerical techniques results to optimize the operating conditions of thermal plasma spraying process. The Lattice Boltzmann method (LBM) is used to scrutinize dispersion effects of injection parameters on droplet impact characteristics when impacting substrate. The validation of the developed model shows good agreement with former findings. The results of spraying Zirconia particles give the values Kmin=88.2, Kmax=367.4, Kmean=273.8 and a standard deviation of 48.0 for the Sommerfeld number. The Taguchi experimental design study is conducted for five operating parameters of two levels. The ensuing retained factors combination give Kmean=258.9. To assess drawn conclusions, confirmation test was performed using the Jets&Poudres software. The results show that the prior way is to coat and particles of dp< 40.3 µm have evaporated, particles 40.3 = dp = 49 µm are fully molten and all particles of dp = 71.9 µm arrive fully solid.

Sign in / Sign up

Export Citation Format

Share Document