scholarly journals A Mechanical Analysis of In Situ Polymerized Poly(butylene terephthalate) Flax Fiber Reinforced Composites Produced by RTM

2013 ◽  
Vol 2013 ◽  
pp. 1-5 ◽  
Author(s):  
C. Romão ◽  
C. M. C. Pereira ◽  
J. L. Esteves

This work addresses mechanical characterization in tension of woven flax fabric reinforced in situ polymerized poly(butylene terephthalate) composites, produced by the RTM technique. A brief description of the developed RTM set-up is made and the composite manufacturing details are presented. A morphological analysis of the mechanically characterized materials by Scanning Electronic Microscopy (SEM) is also made. The produced neat polymer (pCBT) showed a brittle behavior and mechanical properties lower than those found in the literature. Its reinforcement with woven flax fabric resulted in an enhancement of both tensile strength and stiffness. The obtained results can be significantly improved by the polymer modifying chemically , optimizing the control of the processing parameters, and subjecting flax fibers to a surface treatment compatible with the CBT 160 resin.

2014 ◽  
Vol 607 ◽  
pp. 286-289
Author(s):  
Hai Fei Qiu ◽  
Song Lin Wu ◽  
Hong Cai Yang

Trough roller is an important component part on belt conveyor, the carrying capacity of the roller is a basis of belt conveyor. The calculation principle and method of material’s cross section area is deduced in the thesis, and mechanical analysis of the trough roller is carried out based on that, in results, the static load of it is calculated. The finite element model of the trough roller is set up by Simulation /Works software, and then the stress and deformation results of it is clear through finite element statics calculation and analysis. Based on this thesis, some valuable basis and reference are offered to trough roller’s strength and stiffness design.


2017 ◽  
Vol 120 (3) ◽  
pp. 303-322
Author(s):  
D. Pienaar ◽  
B.M. Guy ◽  
C. Pienaar ◽  
K.S. Viljoen

Abstract Mineralogical and textural variability of ores from different sources commonly leads to processing inefficiencies, particularly when a processing plant is designed to treat ore from a single source (i.e. ore of a relatively uniform composition). The bulk of the Witwatersrand ore in the Klerksdorp goldfield, processed at the AngloGold Ashanti Great Noligwa treatment plant, is derived from the Vaal Reef (>90%), with a comparatively small contribution obtained from the Crystalkop Reef (or C-Reef). Despite the uneven contribution, it is of critical importance to ensure that the processing parameters are optimized for the treatment of both the Vaal and C-Reefs. This paper serves to document the results of a geometallurgical study of the C-Reef at the Great Noligwa gold mine in the Klerksdorp goldfield of South Africa, with the primary aim of assessing the suitability of the processing parameters that are in use at the Great Noligwa plant. The paper also draws comparisons between the C-Reef and the Vaal Reef A-facies (Vaal Reef) and attempts to explain minor differences in the recovery of gold and uranium from these two sources. Three samples of the C-Reef were collected in-situ from the underground operations at Great Noligwa mine for mineralogical analyses and metallurgical tests. Laboratory-scale leach tests for gold (cyanide) and uranium (sulphuric acid) were carried out using dissolution conditions similar to that in use at the Great Noligwa plant, followed by further diagnostic leaching in the case of gold. The gold in the ore was found to be readily leachable with recoveries ranging from 95% to 97% (as opposed to 89% to 93% for the Vaal Reef). Additional recoveries were achieved in the presence of excess cyanide (96% to 98%). The recovery of uranium varied between 72% and 76% (as opposed to 30% to 64% for the Vaal Reef), which is substantially higher than predicted, given the amount of brannerite in the ore, which is generally regarded as refractory. Thus, the higher uranium recoveries from the C-Reef imply that a proportion of the uranium was recovered by the partial dissolution of brannerite. As the Vaal Reef contain high amounts of chlorite (3% to 8%), which is an important acid consumer, it is considered likely that this could have reduced the effectiveness of the H2SO4 leach in the case of the ore of the Vaal Reef. Since the gold and uranium recoveries from the C-Reef were higher than the recoveries from the Vaal Reef, the results demonstrate that the processing parameters used for treatment of the Vaal Reef are equally suited to the treatment of the C-Reef. Moreover, small processing modifications, such as increased milling and leach retention times, may well increase the recovery of gold (particularly when e.g. coarse gold, or unexposed gold, is present).


Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2246
Author(s):  
Georgia Charalampous ◽  
Efsevia Fragkou ◽  
Konstantinos A. Kormas ◽  
Alexandre B. De Menezes ◽  
Paraskevi N. Polymenakou ◽  
...  

The diversity and degradation capacity of hydrocarbon-degrading consortia from surface and deep waters of the Eastern Mediterranean Sea were studied in time-series experiments. Microcosms were set up in ONR7a medium at in situ temperatures of 25 °C and 14 °C for the Surface and Deep consortia, respectively, and crude oil as the sole source of carbon. The Deep consortium was additionally investigated at 25 °C to allow the direct comparison of the degradation rates to the Surface consortium. In total, ~50% of the alkanes and ~15% of the polycyclic aromatic hydrocarbons were degraded in all treatments by Day 24. Approximately ~95% of the total biodegradation by the Deep consortium took place within 6 days regardless of temperature, whereas comparable levels of degradation were reached on Day 12 by the Surface consortium. Both consortia were dominated by well-known hydrocarbon-degrading taxa. Temperature played a significant role in shaping the Deep consortia communities with Pseudomonas and Pseudoalteromonas dominating at 25 °C and Alcanivorax at 14 °C. Overall, the Deep consortium showed a higher efficiency for hydrocarbon degradation within the first week following contamination, which is critical in the case of oil spills, and thus merits further investigation for its exploitation in bioremediation technologies tailored to the Eastern Mediterranean Sea.


Polymers ◽  
2021 ◽  
Vol 13 (12) ◽  
pp. 1951
Author(s):  
Yi Di Boon ◽  
Sunil Chandrakant Joshi ◽  
Somen Kumar Bhudolia

Fiber reinforced thermoplastic composites are gaining popularity in many industries due to their short consolidation cycles, among other advantages over thermoset-based composites. Computer aided manufacturing processes, such as filament winding and automated fiber placement, have been used conventionally for thermoset-based composites. The automated processes can be adapted to include in situ consolidation for the fabrication of thermoplastic-based composites. In this paper, a detailed literature review on the factors affecting the in situ consolidation process is presented. The models used to study the various aspects of the in situ consolidation process are discussed. The processing parameters that gave good consolidation results in past studies are compiled and highlighted. The parameters can be used as reference points for future studies to further improve the automated manufacturing processes.


2000 ◽  
Vol 33 (2) ◽  
pp. 344-349 ◽  
Author(s):  
Christopher F. Snook ◽  
Michael D. Purdy ◽  
Michael C. Wiener

A commercial crystallization robot has been modified for use in setting up sitting-drop vapor-diffusion crystallization experiments, and for setting up protein crystallization screensin situ. The primary aim of this effort is the automated screening of crystallization of integral membrane proteins in detergent-containing solutions. However, the results of this work are of general utility to robotic liquid-handling systems. Sources of error that can prevent the accurate dispensing and mixing of solutions have been identified, and include local environmental, machine-specific and solution conditions. Solutions to each of these problems have been developed and implemented.


2006 ◽  
Vol 20 (25n27) ◽  
pp. 4613-4618 ◽  
Author(s):  
R. J. T. LIN ◽  
D. BHATTACHARYYA ◽  
S. FAKIROV

Being a fast growing plastic manufacturing industry, rotational molding has been using the linear polyethylenes extensively as the raw material. As these materials have shown insufficient mechanical properties for certain applications where strength and stiffness of the products are the main concerns, worldwide rotational molders have expressed a need for stronger and stiffer materials to be available for rotomolding. A possible attractive solution may be the recently developed microfibril reinforced composites (MFCs). Blends of linear medium density polyethylene/polyethylene terephthalate (LMDPE/PET) with an MFC structure are manufactured on a commercial-scale set-up and thereafter used in rotational molding. The samples are characterized morphologically and tested mechanically. The results obtained show that the MFC-concept has good application opportunities in the polymer processing including rotational molding.


2002 ◽  
Vol 30 (2) ◽  
pp. 78-82 ◽  
Author(s):  
M. Beier ◽  
M. Baum ◽  
H. Rebscher ◽  
R. Mauritz ◽  
A. Wixmerten ◽  
...  

Concepts and results are described for the use of a single, but extremely flexible, probing tool to address a wide variety of genomic questions. This is achieved by transforming genomic questions into a software file that is used as the design scheme for potentially any genomic assay in a microarray format. Microarray fabrication takes place in three-dimensional microchannel reaction carriers by in situ synthesis based on spatial light modulation. This set-up allows for maximum flexibility in design and realization of genomic assays. Flexibility is achieved at the molecular, genomic and assay levels. We have applied this technology to expression profiling and genotyping experiments.


Author(s):  
Zhe Gao ◽  
Haris Khan ◽  
Jingjing Li ◽  
Weihong Guo

Abstract This research focused on developing a hybrid quality monitoring model through combining the data driven and key engineering parameters to predict the friction stir blind riveting (FSBR) joint quality. The hybrid model was formulated through utilizing the in-situ processing and joint property data. The in-situ data involved sensor fusion (force and torque signals) and key processing parameters (spindle speed, feed rate and stacking sequence) for data-driven modeling. The quality of the FSBR joints was defined by the tensile strength. Further, the joint cross-sectional analysis and failure modes in lap-shear tests were employed to confirm the efficacy of the proposed model and development of the process-structure-property relationship.


2015 ◽  
Vol 15 (17) ◽  
pp. 10087-10092 ◽  
Author(s):  
L. Kattner ◽  
B. Mathieu-Üffing ◽  
J. P. Burrows ◽  
A. Richter ◽  
S. Schmolke ◽  
...  

Abstract. In 1997 the International Maritime Organisation (IMO) adopted MARPOL Annex VI to prevent air pollution by shipping emissions. It regulates, among other issues, the sulfur content in shipping fuels, which is transformed into the air pollutant sulfur dioxide (SO2) during combustion. Within designated Sulfur Emission Control Areas (SECA), the sulfur content was limited to 1 %, and on 1 January 2015, this limit was further reduced to 0.1 %. Here we present the set-up and measurement results of a permanent ship emission monitoring site near Hamburg harbour in the North Sea SECA. Trace gas measurements are conducted with in situ instruments and a data set from September 2014 to January 2015 is presented. By combining measurements of carbon dioxide (CO2) and SO2 with ship position data, it is possible to deduce the sulfur fuel content of individual ships passing the measurement station, thus facilitating the monitoring of compliance of ships with the IMO regulations. While compliance is almost 100 % for the 2014 data, it decreases only very little in 2015 to 95.4 % despite the much stricter limit. We analysed more than 1400 ship plumes in total and for months with favourable conditions, up to 40 % of all ships entering and leaving Hamburg harbour could be checked for their sulfur fuel content.


Sign in / Sign up

Export Citation Format

Share Document