scholarly journals Decolorization of Methylene Blue by Ag/SrSnO3 Composites under Ultraviolet Radiation

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
Patcharanan Junploy ◽  
Titipun Thongtem ◽  
Somchai Thongtem ◽  
Anukorn Phuruangrat
Keyword(s):  
Electron Microscopy ◽  
Methylene Blue ◽  
Uv Radiation ◽  
Photoelectron Spectroscopy ◽  
Separation Process ◽  
X Ray Diffraction ◽  
Electron Hole ◽  
X Ray ◽  
Negative Effect ◽  
Uv Visible

SrSn(OH)6 precursors synthesized by a cyclic microwave radiation (CMR) process were calcined at 900°C for 3 h to form rod-like SrSnO3. Further, the rod-like SrSnO3 and AgNO3 in ethylene glycol (EG) were ultrasonically vibrated to form rod-like Ag/SrSnO3 composites, characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), electron microscopy (EM), Fourier transform infrared (FTIR) spectroscopy, and UV-visible analysis. The photocatalyses of rod-like SrSnO3, 1 wt%, 5 wt%, and 10 wt% Ag/SrSnO3 composites were studied for degradation of methylene blue (MB, C16H18N3SCl) dye under ultraviolet (UV) radiation. In this research, the 5 wt% Ag/SrSnO3 composites showed the highest activity, enhanced by the electron-hole separation process. The photoactivity became lower by the excessive Ag nanoparticles due to the negative effect caused by reduction in the absorption of UV radiation.

TEMPLATE STRATEGY FOR THE SYNTHESIS OF Cu2O–Pt HIERARCHICAL HETEROSTRUCTURES FOR THE DEGRADATION OF METHYLENE BLUE

NANO ◽  
2013 ◽  
Vol 08 (06) ◽  
pp. 1350062 ◽  
Author(s):  
SHIYONG BAO ◽  
HAN ZHU ◽  
PAN WANG ◽  
MEILING ZOU ◽  
MINGLIANG DU ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Methylene Blue ◽  
Photoelectron Spectroscopy ◽  
Pt Nanoparticles ◽  
X Ray Diffraction ◽  
Electron Hole ◽  
X Ray ◽  
Transmission Electron ◽  
Green Route

A facile and green route was introduced to synthesize Pt nanoparticles (PtNPs) immobilized on Cu 2 O octahedrons to form Cu 2 O – Pt hierarchical heterostructure. Transmission electron microscopy (TEM), field emission scanning electron microscopy (FE-SEM), high resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) were employed to study their morphology, chemical and crystallographic properties of the Cu 2 O – Pt hierarchical heterostructure. These novel Cu 2 O – Pt hierarchical heterostructures show fascinating degradations of methylene blue (MB), due to the suppressed electron/hole recombination phenomena and the efficient ability to capture the light.

scholarly journals Facile Template In-Situ Fabrication of ZnCo2O4 Nanoparticles with Highly Photocatalytic Activities under Visible-Light Irradiation

2019 ◽  
Vol 14 (2) ◽  
pp. 404 ◽  
Author(s):  
Vu T. Tan ◽  
La The Vinh ◽  
Tran Ngoc Khiem ◽  
Huynh Dang Chinh
Keyword(s):  
Electron Microscopy ◽  
Methylene Blue ◽  
Surface Area ◽  
Photoelectron Spectroscopy ◽  
High Specific Surface Area ◽  
Bet Surface Area ◽  
X Ray Diffraction ◽  
X Ray ◽  
In Situ Fabrication ◽  
Transmission Electron

High specific surface area ZnCo2O4 nanoparticles were prepared via a sacrificial template accelerated hydrolysis by using nanoparticles of ZnO with highly polar properties as a template. The obtained ZnCo2O4 nanoparticles were characterized by the method of scanning electron microscopy (SEM), X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET) surface area measurements, Transmission electron microscopy (TEM), Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS). The obtained nanoparticles were performed as a photocatalyst for the degradation of methylene blue in aqueous solution under visible irradiation. The photocatalytic degradation rate of methylene blue onto the synthesized ZnCo2O4 was higher than that of commercial ZnO and synthesized ZnO template. Copyright © 2019 BCREC Group. All rights reserved. 

Investigation of the Effect of Uv-Assisted Oxidation and Nitridation of Hafnium Metal Films

2003 ◽  
Vol 780 ◽  
Author(s):  
C. Essary ◽  
V. Craciun ◽  
J. M. Howard ◽  
R. K. Singh
Keyword(s):  
Uv Radiation ◽  
Photoelectron Spectroscopy ◽  
Grazing Angle ◽  
X Ray Diffraction ◽  
Metal Thin Films ◽  
X Ray ◽  
Force Microscopy ◽  
Si Substrates ◽  
Atomic Force ◽  
Silicon Interface

AbstractHf metal thin films were deposited on Si substrates using a pulsed laser deposition technique in vacuum and in ammonia ambients. The films were then oxidized at 400 °C in 300 Torr of O2. Half the samples were oxidized in the presence of ultraviolet (UV) radiation from a Hg lamp array. X-ray photoelectron spectroscopy, atomic force microscopy, and grazing angle X-ray diffraction were used to compare the crystallinity, roughness, and composition of the films. It has been found that UV radiation causes roughening of the films and also promotes crystallization at lower temperatures.Furthermore, increased silicon oxidation at the interface was noted with the UVirradiated samples and was shown to be in the form of a mixed layer using angle-resolved X-ray photoelectron spectroscopy. Incorporation of nitrogen into the film reduces the oxidation of the silicon interface.

scholarly journals Efficient Adsorption of Methylene Blue by Porous Biochar Derived from Soybean Dreg Using a One-Pot Synthesis Method

Molecules ◽  
2021 ◽  
Vol 26 (3) ◽  
pp. 661
Author(s):  
Zhiwei Ying ◽  
Xinwei Chen ◽  
He Li ◽  
Xinqi Liu ◽  
Chi Zhang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Methylene Blue ◽  
Photoelectron Spectroscopy ◽  
Synthesis Method ◽  
Urban Pollution ◽  
Maximum Adsorption Capacity ◽  
One Pot ◽  
Average Pore ◽  
X Ray ◽  
Isotherm Equation

Soybean dreg is a by-product of soybean products production, with a large consumption in China. Low utilization value leads to random discarding, which is one of the important sources of urban pollution. In this work, porous biochar was synthesized using a one-pot method and potassium bicarbonate (KHCO3) with low-cost soybean dreg (SD) powder as the carbon precursor to investigating the adsorption of methylene blue (MB). The prepared samples were characterized with scanning electron microscopy (SEM), transmission electron microscopy (TEM), elemental analyzer (EA), Brunauer-Emmett-Teller (BET), X-ray diffractometer (XRD), Raman spectroscopy (Raman), Fourier transform infrared spectrometer (FTIR), and X-ray photoelectron spectroscopy (XPS). The obtained SDB-K-3 showed a high specific surface area of 1620 m2 g−1, a large pore volume of 0.7509 cm3 g−1, and an average pore diameter of 1.859 nm. The results indicated that the maximum adsorption capacity of SDB-K-3 to MB could reach 1273.51 mg g−1 at 318 K. The kinetic data were most consistent with the pseudo-second-order model and the adsorption behavior was more suitable for the Langmuir isotherm equation. This study demonstrated that the porous biochar adsorbent can be prepared from soybean dreg by high value utilization, and it could hold significant potential for dye wastewater treatment in the future.

scholarly journals Synthesis of Magnetic Ferrocene-Containing Polymer with Photothermal Effects for Rapid Degradation of Methylene Blue

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 558
Author(s):  
Wenhui Zhu ◽  
Caiyun Zhang ◽  
Yali Chen ◽  
Qiliang Deng
Keyword(s):  
Methylene Blue ◽  
Photoelectron Spectroscopy ◽  
Room Temperature ◽  
Degradation Rate ◽  
Model Compound ◽  
Vibrating Sample Magnetometer ◽  
Simulated Sunlight ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ft Ir

Photothermal materials are attracting more and more attention. In this research, we synthesized a ferrocene-containing polymer with magnetism and photothermal properties. The resulting polymer was characterized by Fourier-transform infrared (FT-IR), vibrating sample magnetometer (VSM), scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and thermogravimetric analysis (TGA). Its photo-thermocatalytic activity was investigated by choosing methylene blue (MB) as a model compound. The degradation percent of MB under an irradiated 808 nm laser reaches 99.5% within 15 min, and the degradation rate is 0.5517 min−1, which is 145 times more than that of room temperature degradation. Under irradiation with simulated sunlight, the degradation rate is 0.0092 min−1, which is approximately 2.5 times more than that of room temperature degradation. The present study may open up a feasible route to degrade organic pollutants.

scholarly journals Synthesis of Ce1−xPdxO2−δ Solid Solution in Molten Nitrate

Catalysts ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 640
Author(s):  
Hideaki Sasaki ◽  
Keisuke Sakamoto ◽  
Masami Mori ◽  
Tatsuaki Sakamoto
Keyword(s):  
Electron Microscopy ◽  
Solid Solution ◽  
Solid Solutions ◽  
Photoelectron Spectroscopy ◽  
Synthesis Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Co Precipitation ◽  
Ionic States

CeO2-based solid solutions in which Pd partially substitutes for Ce attract considerable attention, owing to their high catalytic performances. In this study, the solid solution (Ce1−xPdxO2−δ) with a high Pd content (x ~ 0.2) was synthesized through co-precipitation under oxidative conditions using molten nitrate, and its structure and thermal decomposition were examined. The characteristics of the solid solution, such as the change in a lattice constant, inhibition of sintering, and ionic states, were examined using X-ray diffraction (XRD), scanning electron microscopy–energy-dispersive X-ray spectroscopy (SEM−EDS), transmission electron microscopy (TEM)−EDS, and X-ray photoelectron spectroscopy (XPS). The synthesis method proposed in this study appears suitable for the easy preparation of CeO2 solid solutions with a high Pd content.

ROOM TEMPERATURE PHOTOLUMINESCENCE OF POLYCRYSTALLINE SIC PREPARED FROM CARBON-SATURATED SI MELT

2002 ◽  
Vol 16 (06n07) ◽  
pp. 1047-1051
Author(s):  
JIANPING MA ◽  
ZHIMING CHEN ◽  
GANG LU ◽  
MINGBIN YU ◽  
LIANMAO HANG ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Room Temperature ◽  
Uv Light ◽  
X Ray Diffraction ◽  
X Ray ◽  
Room Temperature Photoluminescence ◽  
Composition And Structure ◽  
Light Excitation ◽  
Scanning Electron

Intense photoluminescence (PL) has been observed at room temperature from the polycrystalline SiC samples prepared from carbon-saturated Si melt at a temperature ranging from 1500 to 1650°C. Composition and structure of the samples have been confirmed by means of X-ray photoelectron spectroscopy, X-ray diffraction and scanning electron microscopy. PL measurements with 325 nm UV light excitation revealed that the room temperature PL spectrum of the samples consists of 3 luminescent bands, the peak energies of which are 2.38 eV, 2.77 eV and 3.06 eV, respectively. The 2.38 eV band is much stronger than the others. It is suggested that some extrinsic PL mechanisms associated with defect or interface states would be responsible to the intensive PL observed at room temperature.

scholarly journals Aluminum Nitride-Silicon Carbide Alloy Crystals Grown on SiC Substrates by Sublimation

2005 ◽  
Vol 10 ◽  
Author(s):  
Z. Gu ◽  
L. Du ◽  
J.H. Edgar ◽  
E.A. Payzant ◽  
L. Walker ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
X Ray Diffraction ◽  
Original Source ◽  
X Ray ◽  
Alloy Crystal ◽  
Transmission Electron ◽  
Crystal Substrate ◽  
Vapor Distribution ◽  
Uniform Composition

AlN-SiC alloy crystals, with a thickness greater than 500 µm, were grown on 4H- and 6H-SiC substrates from a mixture of AlN and SiC powders by the sublimation-recondensation method at 1860-1990 °C. On-axis SiC substrates produced a rough surface covered with hexagonal grains, while 6H- and 4H- off-axis SiC substrates with different miscut angles (8° or 3.68°) formed a relatively smooth surface with terraces and steps. The substrate misorientation ensured that the AlN-SiC alloy crystals grew two dimensionally as identified by scanning electron microscopy (SEM). X-ray diffraction (XRD) and transmission electron microscopy (TEM) confirmed that the AlN-SiC alloys had the wurtzite structure. Electron probe microanalysis (EPMA) and x-ray photoelectron spectroscopy (XPS) demonstrated that the resultant alloy crystals had non-stoichiometric ratios of Al:N and Si:C and a uniform composition throughout the alloy crystal from the interface to the surface. The composition ratio of Al:Si of the alloy crystals changed with the growth temperature, and differed from the original source composition, which was consistent with the results predicted by thermodynamic calculation of the solid-vapor distribution of each element. XPS detected the bonding between Si-C, Si-N, Si-O for the Si 2p spectra. The dislocation density decreased with the growth, which was lower than 106 cm−2 at the alloy surface, more than two orders of magnitude lower compared to regions close to the crystal/substrate interface, as determined by TEM.

Optical properties of anatase TiO2 films modified by N ion implantation

2012 ◽  
Vol 90 (1) ◽  
pp. 39-43 ◽  
Author(s):  
X. Xiang ◽  
D. Chang ◽  
Y. Jiang ◽  
C.M. Liu ◽  
X.T. Zu
Keyword(s):  
Thin Films ◽  
Ion Implantation ◽  
Photoelectron Spectroscopy ◽  
Radio Frequency Magnetron Sputtering ◽  
X Ray Diffraction ◽  
X Ray ◽  
Atomic Force ◽  
Light Region ◽  
Uv Visible ◽  
Substrate Temperatures

Anatase TiO2 thin films are deposited on K9 glass samples at different substrate temperatures by radio frequency magnetron sputtering. N ion implantation is performed in the as-deposited TiO2 thin films at ion fluences of 5 × 1016, 1 × 1017, and 5 × 1017 ions/cm2. X-ray diffraction, atomic force microscope, X-ray photoelectron spectroscopy (XPS), and UV–visible spectrophotometer are used to characterize the films. With increasing N ion fluences, the absorption edges of anatase TiO2 films shift to longer wavelengths and the absorbance increases in the visible light region. XPS results show that the red shift of TiO2 films is due to the formation of N–Ti–O compounds. As a result, photoactivity is enhanced with increasing N ion fluence.

Few-Layered MoS2 Nanostructures for Highly Efficient Visible Light Photocatalysis

NANO ◽  
2016 ◽  
Vol 11 (10) ◽  
pp. 1650114 ◽  
Author(s):  
Dan Li ◽  
Jianwei Li ◽  
Caiqin Han ◽  
Xinsheng Zhao ◽  
Haipeng Chu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Visible Light ◽  
Electrochemical Impedance ◽  
X Ray Diffraction ◽  
Electron Hole ◽  
Electrochemical Impedance Spectra ◽  
X Ray ◽  
Transmission Electron ◽  
Electron Hole Pair

Few-layered MoS2 nanostructures were successfully synthesized by a simple hydrothermal method without the addition of any catalysts or surfactants. Their morphology, structure and photocatalytic activity were characterized by X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, transmission electron microscopy, electrochemical impedance spectra and UV-Vis absorption spectroscopy, respectively. These results show that the MoS2 nanostructures synthesized at 180[Formula: see text]C exhibit an optimal visible light photocatalytic activity (99%) in the degradation of Rhodamine B owing to the relatively easier adsorption of pollutants, higher visible light absorption and lower electron–hole pair recombination.

Sign in / Sign up

Export Citation Format

Share Document